|
|
skhan855
Jr. Member
 Offline
Activity: 53
Merit: 1
|
 |
May 27, 2018, 07:51:42 PM |
|
Same issue, did you solved it?
I replaced my hash board under warranty and after replacement got 15 degree
|
|
|
|
|
ces0712 (OP)
Newbie
Offline
Activity: 7
Merit: 0
|
|
May 28, 2018, 02:58:01 PM |
|
nothing yet  |
|
|
|
|
|
VRobb
|
|
May 28, 2018, 03:09:01 PM |
|
What PSU are you using?
|
I don't believe in superstition because it's bad luck: 13thF1oor6CAwyzyxXPNnRvu3nhhYeqZdc
These aren't the Droids you're looking for: S5 & S7 (Sold), R4B2, R4B4 (RIP), 2x S9 obsolete, 2xS15-28, S17-56, S17-70
Pushing a whopping 1/5 PH! Oh The SPEED!!!
|
|
|
ces0712 (OP)
Newbie
Offline
Activity: 7
Merit: 0
|
|
May 28, 2018, 03:18:30 PM |
|
APW3++ provided by the bitmain site in fact i purchased the PSU with the antminer
|
|
|
|
|
|
VRobb
|
|
May 28, 2018, 03:52:16 PM |
|
What input voltage to the PSU? If it's only 110V then that's your problem. The bitmain PSU is only rated for the full 1600W output with 220V input, less if you're on 110V...
|
I don't believe in superstition because it's bad luck: 13thF1oor6CAwyzyxXPNnRvu3nhhYeqZdc
These aren't the Droids you're looking for: S5 & S7 (Sold), R4B2, R4B4 (RIP), 2x S9 obsolete, 2xS15-28, S17-56, S17-70
Pushing a whopping 1/5 PH! Oh The SPEED!!!
|
|
|
ces0712 (OP)
Newbie
Offline
Activity: 7
Merit: 0
|
|
May 28, 2018, 04:39:26 PM |
|
it has double input
1.- input 110V - 14A
2.- input 220V - 10A
i assume i can connect either 110V or 220V of course i am consuming more power at 110V
|
|
|
|
|
|
VRobb
|
|
May 28, 2018, 04:44:58 PM |
|
What input voltage to the PSU? If it's only 110V then that's your problem. The bitmain PSU is only rated for the full 1600W output with 220V input, less if you're on 110V...
So I ask again, what input voltage are you using? |
I don't believe in superstition because it's bad luck: 13thF1oor6CAwyzyxXPNnRvu3nhhYeqZdc
These aren't the Droids you're looking for: S5 & S7 (Sold), R4B2, R4B4 (RIP), 2x S9 obsolete, 2xS15-28, S17-56, S17-70
Pushing a whopping 1/5 PH! Oh The SPEED!!!
|
|
|
ces0712 (OP)
Newbie
Offline
Activity: 7
Merit: 0
|
|
May 28, 2018, 04:55:52 PM |
|
Ok thanks for the answer i miss the point sorry 1200W for 110V, i am currently using 110V
|
|
|
|
|
ces0712 (OP)
Newbie
Offline
Activity: 7
Merit: 0
|
|
May 28, 2018, 05:10:20 PM |
|
The issue also is if i disconnect the other boards and leaving the one with the problem the behavior is the same keeps showing 0.0000
|
|
|
|
|
|
VRobb
|
|
May 28, 2018, 06:28:37 PM |
|
Ah, well that is another kind of failure, unfortunately not as uncommon on S9's as it should be. If you do see the board hashing for a bit before it drops out on a cold restart perhaps a cleaning would help. Otherwise repair starts to be the only solution, or just run it as a 2/3rds S9 (S6?).
|
I don't believe in superstition because it's bad luck: 13thF1oor6CAwyzyxXPNnRvu3nhhYeqZdc
These aren't the Droids you're looking for: S5 & S7 (Sold), R4B2, R4B4 (RIP), 2x S9 obsolete, 2xS15-28, S17-56, S17-70
Pushing a whopping 1/5 PH! Oh The SPEED!!!
|
|
|
ces0712 (OP)
Newbie
Offline
Activity: 7
Merit: 0
|
|
May 28, 2018, 06:38:18 PM |
|
Ok thanks, i will try a little of cleaning and also do some work with my electricity to put the input voltage 220V, i will cross my fingers, after all the hope is the last thing it dies if not repair as you said or work with 2/3 of the S9 i will keep you inform after i do that for anybody else that is presenting the same issues
|
|
|
|
|
|
