Need help with syntax of CGMINER

[inachu]

I did ask in CGMINER but it was removed and since I am new here I guess this is the next best place to
pst the help I need:

Reading up on solo mining and I am just curious about the syntax

cgminer   put in arguments then username password

If I am doing this on a windows box then does any username and password work?
Or do I have to go into user account and create a account example  BOB and give BOB account a password or
does cgminer not look at that and uses its own http authentication and just use any username and password on the fly?

I did glance over the proper syntax but no idea at all on username and password.


cgminer -o http://localhost:8332 -u username -p password --btc-address 15qSxP1SQcUX3o4nhkfdbgyoWEFMomJ4rZ

So can I keep it as localhost or change it to 192.168.1.1:8332  (in the windows world it should be the same no?

Does CGMINER use windows authentication?   If so then I must create a new account

So far I think the following is correct:
cgminer -o http://localhost:8332 -u default -p password1 --btc-address 33-put my address here-ozSsU

[nc50lc]

Since you've specified "localhost:8332" you must have a local Bitcoin node (Bitcoin Core) in your PC?
This wasn't mentioned but it also needs to be fully synced to work;
then do this:

SOLO MINING
-snip-
To enable solo mining, one must be running a local
bitcoind/bitcoin-qt or have one they have rpc access to. To do this, edit your
bitcoind configuration file (bitcoin.conf) with the following extra lines,
using your choice of username and password:

rpcuser=username
rpcpassword=password

Restart bitcoind

Based from that quote, the "username" and "password" are your "rpcuser" and "rpcpassword" (after the =).
I haven't tried solo mining since it's not recommended, so you have to figure out the rest.

[unsoindovo]

I did ask in CGMINER but it was removed and since I am new here I guess this is the next best place to
pst the help I need:

Reading up on solo mining and I am just curious about the syntax

cgminer   put in arguments then username password

If I am doing this on a windows box then does any username and password work?
Or do I have to go into user account and create a account example  BOB and give BOB account a password or
does cgminer not look at that and uses its own http authentication and just use any username and password on the fly?

I did glance over the proper syntax but no idea at all on username and password.


cgminer -o http://localhost:8332 -u username -p password --btc-address 15qSxP1SQcUX3o4nhkfdbgyoWEFMomJ4rZ

So can I keep it as localhost or change it to 192.168.1.1:8332  (in the windows world it should be the same no?

Does CGMINER use windows authentication?   If so then I must create a new account

So far I think the following is correct:
cgminer -o http://localhost:8332 -u default -p password1 --btc-address 33-put my address here-ozSsU

hi mate!
i hope you have already resolved your issue.
anyway, i think you were removed from there because your question was already answered.
Yout post was just considered a duplicate and removed for that.
try to search better ;-)

[MATHReX]

The local bitcoin core wallet doesn't support solo mining anymore.
So even if your syntax is correct for cgminer, it will never work.

Check this message out: https://bitcointalk.org/index.php?topic=1013986.msg11902675#msg11902675

[nc50lc]

Right, the post in your link said:

-snip-
Cgminer can, but it is only designed to support ASIC mining hardware.
-snip-

Means it can (but the post was from 2015)
The 1st part means that the node cannot do the mining anymore since usually, full nodes have a built-in feature for solo mining.
But since Bitcoin became non-CPU/GPU friendly, they've taken out the feature.

@inachu Care to tell us your goal and available hardware(s)?
I'm sure it's not for profit unless you have a Big ASIC farm.