Hello,
I have interesting problem with T17e, connected is only 1 bad hashboard.
Where is a bring up temperature sensor located? is it one of 4 sensors on the board ?
Hash board sometimes booting up without hashing and after 5minutes reboot.
Problem with MOS, DC/DC ? Overcurrent ? or soft voltage ?
Control board find 78 asic chips.
And second question, what means "domain d0,d1,d2,d3 ?
2021-08-15 16:10:43 chain 0 domain 3: d0 0.334, d1 0.329, d2 0.333, d3 0.320, sum = 1.316162
Here is part of the log:
2021-08-15 16:10:43 chain 0 domain 0: d0 0.387, d1 0.390, d2 0.406, d3 0.316, sum = 1.499634
2021-08-15 16:10:43 chain 0 domain 1: d0 0.375, d1 0.382, d2 0.361, d3 0.374, sum = 1.492310
2021-08-15 16:10:43 chain 0 domain 2: d0 0.402, d1 0.397, d2 0.394, d3 0.307, sum = 1.499634
2021-08-15 16:10:43 chain 0 domain 3: d0 0.334, d1 0.329, d2 0.333, d3 0.320, sum = 1.316162
2021-08-15 16:10:43 chain 0 domain 4: d0 0.397, d1 0.380, d2 0.402, d3 0.321, sum = 1.499634
2021-08-15 16:10:43 chain 0 domain 5: d0 0.382, d1 0.374, d2 0.376, d3 0.361, sum = 1.493042
2021-08-15 16:10:43 chain 0 domain 6: d0 0.377, d1 0.382, d2 0.378, d3 0.363, sum = 1.499634
2021-08-15 16:10:43 chain 0 domain 7: d0 0.386, d1 0.376, d2 0.378, d3 0.359, sum = 1.498901
2021-08-15 16:10:43 chain 0 domain 8: d0 0.403, d1 0.387, d2 0.397, d3 0.312, sum = 1.499634
2021-08-15 16:10:43 chain 0 domain 9: d0 0.385, d1 0.383, d2 0.382, d3 0.350, sum = 1.499634
2021-08-15 16:10:43 chain 0 domain 10: d0 0.381, d1 0.381, d2 0.371, d3 0.367, sum = 1.499634
2021-08-15 16:10:43 chain 0 domain 11: d0 0.390, d1 0.391, d2 0.392, d3 0.326, sum = 1.499634
2021-08-15 16:10:44 chain 0 domain 12: d0 0.376, d1 0.375, d2 0.371, d3 0.367, sum = 1.490112
2021-08-15 16:10:44 driver/driver-hash-chip.c:119:set_ldo_ctrl: Set LDO to 0x2000203
2021-08-15 16:10:44 voltage[0] = 1850
2021-08-15 16:10:44 Highest voltage is 20.00
2021-08-15 16:10:44 driver/power_api.c:279:set_working_voltage: working_voltage = 18.500000
2021-08-15 16:10:45 driver/temperature.c:321:calibrate_temp_sensor_all_chains: chain 0 temp sensor NCT218, offset -8
2021-08-15 16:10:45 driver/uart.c:49:set_baud: set UART baud to 12000000
2021-08-15 16:11:11 driver/driver-btm-api.c:662:check_bringup_temp: Bring up temperature is -64
2021-08-15 16:11:11 driver/driver-btm-api.c:204:set_miner_status: ERROR_TEMP_TOO_LOW
2021-08-15 16:11:13 driver/driver-btm-api.c:717:killall_hashboard: ****power off hashboard****
2021-08-15 16:11:13 driver/driver-btm-api.c:157:stop_mining: stop mining: Environment temperature is too low!
2021-08-15 16:11:13 driver/thread.c:1732:cancel_read_nonce_reg_thread: cancel thread
Thank you.
M.