sfury (OP)
Newbie
Offline
Activity: 3
Merit: 0
|
|
December 29, 2021, 10:43:41 PM |
|
Any help or direction would be very much appreciated. Picked up a new s19 and upon starting it up, came across a few problems. Notably got an abnormal hash rate on the dashboard. Noticed that hash board 2 and 3 were not working and hash board 1 was mining very low (below 100Ghz). Did a few troubleshooting steps, rebooted several times, changed PDU (on 240v 30a), updated the firmware via web ui, reset to factory, reseated plugs/cables from control board to hash boards. Have a ticket opened with bitmain but they have not been much help. I do see in the log that “trace_printk()” was showing. Question is if this is the problem, how would I get around the debug kernel? Appreciate any help. thanks in advance! [ 0.000000@0] Booting Linux on physical CPU 0x0 [ 0.000000@0] Linux version 4.9.113 (jenkins@nomd-nomd-fwc-bj) (gcc version 6.3.1 20170109 (Linaro GCC 6.3-2017.02) ) #1 SMP PREEMPT Wed Oct 20 18:57:17 CST 2021 [ 0.000000@0] Boot CPU: AArch64 Processor [410fd034] [ 0.000000@0] earlycon: aml_uart0 at MMIO 0x00000000ff803000 (options '') [ 0.000000@0] bootconsole [aml_uart0] enabled [ 0.000000@0] efi: Getting EFI parameters from FDT: [ 0.000000@0] efi: UEFI not found. [ 0.000000@0] 07400000 - 07500000, 1024 KB, ramoops@0x07400000 [ 0.000000@0] __reserved_mem_alloc_size, start:0x0000000005000000, end:0x0000000005400000, len:4 MiB [ 0.000000@0] 05000000 - 05400000, 4096 KB, linux,secmon [ 0.000000@0] __reserved_mem_alloc_size, start:0x000000003e000000, end:0x0000000040000000, len:32 MiB [ 0.000000@0] failed to allocate memory for node linux,meson-fb, size:32 MB [ 0.000000@0] cma: Reserved 8 MiB at 0x000000000f800000 [ 0.000000@0] On node 0 totalpages: 65536 [ 0.000000@0] DMA zone: 1024 pages used for memmap [ 0.000000@0] DMA zone: 0 pages reserved [ 0.000000@0] DMA zone: 65536 pages, LIFO batch:15 [ 0.000000@0] psci: probing for conduit method from DT. [ 0.000000@0] psci: PSCIv1.0 detected in firmware. [ 0.000000@0] psci: Using standard PSCI v0.2 function IDs [ 0.000000@0] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000@0] psci: SMC Calling Convention v1.1 [ 0.000000@0] percpu: Embedded 25 pages/cpu @ffffffc00f753000 s64536 r8192 d29672 u102400 [ 0.000000@0] pcpu-alloc: s64536 r8192 d29672 u102400 alloc=25*4096 [ 0.000000@0] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000@0] Detected VIPT I-cache on CPU0 [ 0.000000@0] CPU features: enabling workaround for ARM erratum 845719 [ 0.000000@0] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 64512 [ 0.000000@0] Kernel command line: init=/init console=ttyS0,115200 no_console_suspend earlycon=aml_uart,0xff803000 ramoops.pstore_en=1 ramoops.record_size=0x8000 ramoops.console_size=0x4000 logo=,loaded,androidboot.selinux=enforcing androidboot.firstboot=1 jtag=disable androidboot.hardware=amlogic androidboot.bootloader=U-Boot 2015.01 androidboot.build.expect.baseband=N/A androidboot.serialno=1234567890 androidboot.rpmb_state=0 rootfstype=ramfs init=/sbin/init [ 0.000000@0] PID hash table entries: 1024 (order: 1, 8192 bytes) [ 0.000000@0] Dentry cache hash table entries: 32768 (order: 6, 262144 bytes) [ 0.000000@0] Inode-cache hash table entries: 16384 (order: 5, 131072 bytes) [ 0.000000@0] Memory: 219920K/262144K available (8764K kernel code, 1194K rwdata, 2428K rodata, 3648K init, 1018K bss, 29936K reserved, 12288K cma-reserved) [ 0.000000@0] Virtual kernel memory layout: [ 0.000000@0] modules : 0xffffff8000000000 - 0xffffff8008000000 ( 128 MB) [ 0.000000@0] vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000 ( 250 GB) [ 0.000000@0] .text : 0xffffff8009080000 - 0xffffff8009910000 ( 8768 KB) [ 0.000000@0] .rodata : 0xffffff8009910000 - 0xffffff8009b80000 ( 2496 KB) [ 0.000000@0] .init : 0xffffff8009b80000 - 0xffffff8009f10000 ( 3648 KB) [ 0.000000@0] .data : 0xffffff8009f10000 - 0xffffff800a03aa00 ( 1195 KB) [ 0.000000@0] .bss : 0xffffff800a03aa00 - 0xffffff800a139534 ( 1019 KB) [ 0.000000@0] fixed : 0xffffffbefe7fb000 - 0xffffffbefec00000 ( 4116 KB) [ 0.000000@0] PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000 ( 16 MB) [ 0.000000@0] vmemmap : 0xffffffbf00000000 - 0xffffffc000000000 ( 4 GB maximum) [ 0.000000@0] 0xffffffbf00000000 - 0xffffffbf00400000 ( 4 MB actual) [ 0.000000@0] memory : 0xffffffc000000000 - 0xffffffc010000000 ( 256 MB) [ 0.000000@0] can't find symbol:arm_dma_alloc [ 0.000000@0] can't find symbol:__alloc_from_contiguous [ 0.000000@0] can't find symbol:cma_allocator_alloc [ 0.000000@0] 0, addr:ffffff800971cff0 + 140, aml_cma_alloc_post_hook [ 0.000000@0] 1, addr:ffffff800951f258 + 78, dma_alloc_from_contiguous [ 0.000000@0] 2, addr:ffffff80091fdd50 + 388, cma_alloc [ 0.000000@0] 3, addr:ffffff80091f76c8 + 2d0, __kmalloc_track_caller [ 0.000000@0] 4, addr:ffffff80091f4a70 + 2d0, __kmalloc [ 0.000000@0] 5, addr:ffffff80091f4750 + 258, kmem_cache_alloc_trace [ 0.000000@0] 6, addr:ffffff80091f4500 + 250, kmem_cache_alloc [ 0.000000@0] 7, addr:ffffff80091f4490 + 70, __slab_alloc.isra.24.constprop.28 [ 0.000000@0] 8, addr:ffffff80091f4108 + 388, ___slab_alloc.constprop.29 [ 0.000000@0] 9, addr:ffffff80091f1e70 + 420, new_slab [ 0.000000@0] 10, addr:ffffff80091e52f8 + b0, vzalloc [ 0.000000@0] 11, addr:ffffff80091e5248 + b0, vmalloc [ 0.000000@0] 12, addr:ffffff80091e4b00 + 2e0, __vmalloc_node_range [ 0.000000@0] 13, addr:ffffff80091ca410 + 110, kmalloc_order_trace [ 0.000000@0] 14, addr:ffffff80091ca2a0 + 170, kmalloc_order [ 0.000000@0] 15, addr:ffffff80091ab5a8 + 168, __alloc_page_frag [ 0.000000@0] 16, addr:ffffff80091ab540 + 68, alloc_pages_exact [ 0.000000@0] 17, addr:ffffff80091ab510 + 30, get_zeroed_page [ 0.000000@0] 18, addr:ffffff80091ab4b8 + 58, __get_free_pages [ 0.000000@0] 19, addr:ffffff80091aa800 + cb8, __alloc_pages_nodemask [ 0.000000@0] 20, addr:ffffff800909c6e8 + 2a8, __dma_alloc [ 0.000000@0] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000@0] Preemptible hierarchical RCU implementation. [ 0.000000@0] Build-time adjustment of leaf fanout to 64. [ 0.000000@0] RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4. [ 0.000000@0] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4 [ 0.000000@0] [ 0.000000@0] ********************************************************** [ 0.000000@0] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE ** [ 0.000000@0] ** ** [ 0.000000@0] ** trace_printk() being used. Allocating extra memory. ** [ 0.000000@0] ** ** [ 0.000000@0] ** This means that this is a DEBUG kernel and it is ** [ 0.000000@0] ** unsafe for production use. ** [ 0.000000@0] ** ** [ 0.000000@0] ** If you see this message and you are not debugging ** [ 0.000000@0] ** the kernel, report this immediately to your vendor! ** [ 0.000000@0] ** ** [ 0.000000@0] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE ** [ 0.000000@0] ********************************************************** [ 0.000000@0] NR_IRQS:64 nr_irqs:64 0 [ 0.000000@0] irq_meson_gpio: 100 to 8 gpio interrupt mux initialized [ 0.000000@0] axg_aoclkc_init: register ao clk ok! [ 0.000000@0] axg_amlogic_init_sdemmc: register amlogic sdemmc clk [ 0.000000@0] axg_amlogic_init_sdemmc: register amlogic sdemmc clk [ 0.000000@0] axg_amlogic_init_media: register meson media clk [ 0.000000@0] axg_amlogic_init_misc: register amlogic axg misc clks [ 0.000000@0] axg_amlogic_init_misc: register amlogic sdemmc clk [ 0.000000@0] axg_clkc_init initialization complete [ 0.000000@0] arm_arch_timer: Architected cp15 timer(s) running at 24.00MHz (phys). [ 0.000000@0] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.000004@0] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.008253@0] meson_bc_timer: mclk->mux_reg =ffffff800800a190,mclk->reg =ffffff800800c194 [ 0.016912@0] Console: colour dummy device 80x25 [ 0.021110@0] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000) [ 0.031586@0] pid_max: default: 32768 minimum: 301 [ 0.036442@0] thread_stack_cache_init, vmap:ffffffc00edaf600, bitmap:ffffffc00eda3000, cache page:ede0 [ 0.045772@0] thread_stack_cache_init, allocation vm area:ffffffc00edd94c0, addr:ffffff8020000000, size:20001000 [ 0.056005@0] cpu 0, vmap_stack:[ffffffc00f75c960-ffffffc00f760950] [ 0.062304@0] cpu 0, irq_stack: [ffffffc00f753060-ffffffc00f757050] [ 0.068604@0] cpu 1, vmap_stack:[ffffffc00f775960-ffffffc00f779950] [ 0.074903@0] cpu 1, irq_stack: [ffffffc00f76c060-ffffffc00f770050] [ 0.081203@0] cpu 2, vmap_stack:[ffffffc00f78e960-ffffffc00f792950] [ 0.087503@0] cpu 2, irq_stack: [ffffffc00f785060-ffffffc00f789050] [ 0.093804@0] cpu 3, vmap_stack:[ffffffc00f7a7960-ffffffc00f7ab950] [ 0.100103@0] cpu 3, irq_stack: [ffffffc00f79e060-ffffffc00f7a2050] [ 0.106466@0] Security Framework initialized [ 0.110696@0] SELinux: Initializing. [ 0.114388@0] SELinux: Starting in permissive mode [ 0.114428@0] Mount-cache hash table entries: 512 (order: 0, 4096 bytes) [ 0.121108@0] Mountpoint-cache hash table entries: 512 (order: 0, 4096 bytes) [ 0.128870@0] ftrace: allocating 30089 entries in 118 pages [ 0.184563@0] sched-energy: CPU device node has no sched-energy-costs [ 0.185379@0] CPU0: update cpu_capacity 1024 [ 0.189706@0] ASID allocator initialised with 32768 entries [ 0.227690@0] secmon: can't fine clear_range [ 0.227901@0] EFI services will not be available. [ 0.231174@0] Meson chip version = RevC (25:C - 23:0) [ 0.265037@1] Detected VIPT I-cache on CPU1 [ 0.265097@1] CPU1: update cpu_capacity 1024 [ 0.265099@1] CPU1: Booted secondary processor [410fd034] [ 0.293112@2] Detected VIPT I-cache on CPU2 [ 0.293168@2] CPU2: update cpu_capacity 1024 [ 0.293170@2] CPU2: Booted secondary processor [410fd034] [ 0.321163@3] Detected VIPT I-cache on CPU3 [ 0.321215@3] CPU3: update cpu_capacity 1024 [ 0.321218@3] CPU3: Booted secondary processor [410fd034] [ 0.321308@0] Brought up 4 CPUs [ 0.360526@0] SMP: Total of 4 processors activated. [ 0.365435@0] CPU features: detected feature: 32-bit EL0 Support [ 0.371471@0] CPU features: detected feature: Kernel page table isolation (KPTI) [ 0.382038@0] CPU: All CPU(s) started at EL2 [ 0.383212@0] alternatives: patching kernel code [ 0.388532@1] addr:ffffff802007be10 is in kernel, size fix 4096->10, data:mode=0755 [ 0.395741@0] devtmpfs: initialized [ 0.411216@0] DMI not present or invalid. [ 0.411574@0] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.419597@0] futex hash table entries: 1024 (order: 4, 65536 bytes) [ 0.426159@0] pinctrl core: initialized pinctrl subsystem [ 0.432584@0] NET: Registered protocol family 16 [ 0.452104@0] cpuidle: using governor menu [ 0.452612@0] vdso: 2 pages (1 code @ ffffff8009917000, 1 data @ ffffff8009f14000) [ 0.458223@0] hw-breakpoint: found 6 breakpoint and 2 watchpoint registers. [ 0.465633@0] DMA: preallocated 256 KiB pool for atomic allocations [ 0.471798@0] clkmsr: clkmsr: driver init [ 0.475829@0] aml_watch_point_probe, in, wp:2 [ 0.481281@0] pstore: using zlib compression [ 0.484754@0] console [pstore-1] enabled [ 0.488093@0] pstore: Registered ramoops as persistent store backend [ 0.494506@0] ramoops: attached 0x100000@0x7400000, ecc: 0/0 [ 0.508880@0] aml_iomap: amlogic iomap probe done [ 0.515820@0] clkmsr: msr_clk_reg0=ffffff800817e004,msr_clk_reg2=ffffff80081d100c [ 0.517753@0] clkmsr ffd18004.meson_clk_msr: failed to get msr ring reg0 [ 0.614386@0] usbcore: registered new interface driver usbfs [ 0.614550@0] usbcore: registered new interface driver hub [ 0.620184@0] usbcore: registered new device driver usb [ 0.625504@0] pps_core: LinuxPPS API ver. 1 registered [ 0.630403@0] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 0.639802@0] PTP clock support registered [ 0.644159@0] dmi: Firmware registration failed. [ 0.652935@0] secmon: reserve_mem_size:0x300000 [ 0.653108@0] secmon secmon: assigned reserved memory node linux,secmon [ 0.660120@0] secmon: get page:ffffffbf00140000, 5000 [ 0.664768@0] secmon: share in base: 0xffffffc0050fe000, share out base: 0xffffffc0050ff000 [ 0.673152@0] secmon: phy_in_base: 0x50fe000, phy_out_base: 0x50ff000 [ 0.681073@0] NetLabel: Initializing [ 0.683202@0] NetLabel: domain hash size = 128 [ 0.687789@0] NetLabel: protocols = UNLABELED CIPSOv4 [ 0.693039@0] NetLabel: unlabeled traffic allowed by default [ 0.699656@0] clocksource: Switched to clocksource arch_sys_counter [ 0.829002@0] VFS: Disk quotas dquot_6.6.0 [ 0.829150@0] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.856106@0] NET: Registered protocol family 2 [ 0.857174@0] TCP established hash table entries: 2048 (order: 2, 16384 bytes) [ 0.862383@0] TCP bind hash table entries: 2048 (order: 3, 32768 bytes) [ 0.869018@0] TCP: Hash tables configured (established 2048 bind 2048) [ 0.875620@0] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.881568@0] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.888324@0] NET: Registered protocol family 1 [ 0.893283@0] RPC: Registered named UNIX socket transport module. [ 0.898701@0] RPC: Registered udp transport module. [ 0.903579@0] RPC: Registered tcp transport module. [ 0.908478@0] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.917707@0] Unpacking initramfs... [ 1.418126@2] Initramfs unpacking failed: junk in compressed archive [ 1.424970@2] Freeing initrd memory: 6536K [ 1.425882@2] hw perfevents: clusterb_enabled = 0 [ 1.428198@2] hw perfevents: cpumasks 0xf, 0x0 [ 1.432679@2] hw perfevents: cluster A irq = 7 [ 1.437243@2] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available [ 1.447449@2] audit: initializing netlink subsys (disabled) [ 1.450808@2] audit: type=2000 audit(1.264:1): initialized [ 1.458093@2] workingset: timestamp_bits=62 max_order=16 bucket_order=0 [ 1.482954@2] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 1.486036@2] NFS: Registering the id_resolver key type [ 1.488693@2] Key type id_resolver registered [ 1.492996@2] Key type id_legacy registered [ 1.497656@2] fuse init (API version 7.26) [ 1.503076@2] SELinux: Registering netfilter hooks [ 1.509365@2] NET: Registered protocol family 38 [ 1.509427@2] Key type asymmetric registered [ 1.512666@2] Asymmetric key parser 'x509' registered [ 1.518177@2] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248) [ 1.525364@2] io scheduler noop registered (default) [ 1.530340@2] io scheduler deadline registered [ 1.535211@2] io scheduler cfq registered [ 1.556498@3] random: fast init done [ 1.556598@3] random: crng init done [ 1.557069@2] Unable to detect cache hierarchy for CPU 0 [ 1.589925@2] loop: module loaded [ 1.595511@2] zram: Added device: zram0 [ 1.595957@2] mtdoops: mtd device (mtddev=name/number) must be supplied [ 1.600979@2] libphy: Fixed MDIO Bus: probed [ 1.605460@2] tun: Universal TUN/TAP device driver, 1.6 [ 1.609931@2] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> [ 1.618105@2] ee eth reset:Addr = ffffff80081fd008 [ 1.625647@2] meson6-dwmac ff3f0000.ethernet: no reset control found [ 1.627575@2] stmmac - user ID: 0x11, Synopsys ID: 0x37 [ 1.632849@2] Ring mode enabled [ 1.636082@2] DMA HW capability register supported [ 1.640795@2] Normal descriptors [ 1.644128@2] RX Checksum Offload Engine supported [ 1.649019@2] COE Type 2 [ 1.651627@2] TX Checksum insertion supported [ 1.656109@2] Wake-Up On Lan supported [ 1.660059@2] Enable RX Mitigation via HW Watchdog Timer [ 1.673725@2] libphy: stmmac: probed [ 1.673777@2] eth%d: PHY ID 0007c0f1 at 0 IRQ POLL (stmmac-0:00) active [ 1.680309@2] PPP generic driver version 2.4.2 [ 1.683187@2] PPP BSD Compression module registered [ 1.687714@2] PPP Deflate Compression module registered [ 1.692972@2] PPP MPPE Compression module registered [ 1.697928@2] NET: Registered protocol family 24 [ 1.703426@2] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.709324@2] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.716380@2] usbcore: registered new interface driver cdc_acm [ 1.721569@2] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters [ 1.730022@2] usbcore: registered new interface driver usbserial [ 1.736734@3] mousedev: PS/2 mouse device common for all mice [ 1.742157@3] usbcore: registered new interface driver xpad [ 1.747555@2] i2c /dev entries driver [ 1.752356@2] cpu cpu0: bL_cpufreq_init: CPU 0 initialized [ 1.756557@2] arm_big_little: bL_cpufreq_register: Registered platform driver: scpi [ 1.767473@2] ff803000.serial: clock gate not found [ 1.769099@2] meson_uart ff803000.serial: ==uart0 reg addr = ffffff800830d000 [ 1.776254@2] ff803000.serial: ttyS0 at MMIO 0xff803000 (irq = 13, base_baud = 1500000) is a meson_uart [ 1.791186@2] meson_uart ff803000.serial: ttyS0 use xtal(24M) 24000000 change 0 to 115200 [ 1.793896@2] console [ttyS0] enabled [ 1.801106@2] bootconsole [aml_uart0] disabled [ 1.810829@1] ff804000.serial: clock gate not found [ 1.814909@1] meson_uart ff804000.serial: ==uart3 reg addr = ffffff8008321000 [ 1.822014@1] ff804000.serial: ttyS3 at MMIO 0xff804000 (irq = 14, base_baud = 1500000) is a meson_uart [ 1.832384@0] meson_uart ffd24000.serial: ==uart1 reg addr = ffffff8008323000 [ 1.838510@0] ffd24000.serial: ttyS1 at MMIO 0xffd24000 (irq = 25, base_baud = 1500000) is a meson_uart [ 1.848715@2] meson_uart ffd23000.serial: ==uart2 reg addr = ffffff8008325000 [ 1.854980@2] ffd23000.serial: ttyS2 at MMIO 0xffd23000 (irq = 26, base_baud = 1500000) is a meson_uart [ 1.865967@1] amlogic-new-usb2 ffe09000.usb2phy: USB2 phy probe:phy_mem:0xffe09000, iomap phy_base:0xffffff8008348000 [ 1.875249@1] amlogic-new-usb3 ffe09080.usb3phy: This phy has no usb port [ 1.881721@1] amlogic-new-usb3 ffe09080.usb3phy: USB3 phy probe:phy_mem:0xffe09080, iomap phy_base:0xffffff800834c080 [ 1.896816@0] i2c i2c-1: of_i2c: modalias failure on /soc/aobus@ff800000/i2c@5000/mcu6350@40 [ 1.900557@0] i2c i2c-1: Failed to create I2C device for /soc/aobus@ff800000/i2c@5000/mcu6350@40 [ 1.912974@0] aml_dma ff63e000.aml_dma: Aml dma [ 1.916070@0] aml_aes_dma ff63e000.aml_dma:aml_aes: Aml AES_dma [ 1.921038@0] aml_sha_dma ff63e000.aml_dma:aml_sha: Aml SHA1/SHA224/SHA256 dma [ 1.927438@0] efusekeynum: 4 [ 1.929772@0] efusekeyname: mac offset: 0 size: 6 [ 1.936168@0] efusekeyname: mac_bt offset: 6 size: 6 [ 1.942571@0] efusekeyname: mac_wifi offset: 12 size: 6 [ 1.948987@0] efusekeyname: usid offset: 18 size: 16 [ 1.955895@3] efuse efuse: probe OK! [ 1.961771@3] meson-mmc: mmc driver version: 3.02, 2017-05-15: New Emmc Host Controller [ 1.968546@0] meson-mmc: >>>>>>>>hostbase ffffff8008358000, dmode [ 1.973621@0] meson-mmc: actual_clock :400000, HHI_nand: 0x80 [ 1.978803@0] meson-mmc: [meson_mmc_clk_set_rate_v3] after clock: 0x1000033c [ 2.023699@0] meson-mmc: meson_mmc_probe() : success! [ 2.023980@0] amlogic mtd driver init [ 2.028024@0] prase_get_dtb_nand_parameter:128,parse dts start [ 2.032766@0] bl mode descrete [ 2.035625@0] fip_copies 4 [ 2.038332@0] fip_size 0x200000 [ 2.041450@0] nand_clk_ctrl 0xffe07000 [ 2.045173@0] prase_get_dtb_nand_parameter:234,parse dts end [ 2.050841@0] nand_clk_ctrl 0xffe07000 [ 2.054564@0] nand register base ffffff80083df800, nand clock register ffffff80083e1000 [ 2.063309@0] plat->aml_nand_device ffffff800a005a90 [ 2.067470@0] m3_nand_probe() aml_nand_device ffffff800a005a90 [ 2.073587@0] NAND device id: 2c da 90 95 6 0 [ 2.077613@0] NAND device: Manufacturer ID: [ 2.081668@0] 0x2c, Chip ID: 0x2c (Micron A revision NAND 2Gib MT29F2G08-A) [ 2.088709@0] oob_fill_cnt =32 oob_size =64, bch_bytes =14 [ 2.094142@0] ecc mode:6 ecc_page_num=2 eep_need_oobsize=16 [ 2.099690@0] plane_num=1 writesize=0x800 ecc.size=0x200 bch_mode=1 [ 2.105935@0] mtd->oobavail: 0x8 [ 2.109365@0] aml_nand_init 2119: plat-name:bootloader [ 2.114257@0] Creating 1 MTD partitions on "bootloader": [ 2.119542@0] 0x000000000000-0x000000200000 : "bootloader" [ 2.128311@1] bootloader initialized ok [ 2.128802@1] plat->aml_nand_device ffffff800a005a90 [ 2.133795@1] m3_nand_probe() aml_nand_device ffffff800a005a90 [ 2.139960@1] NAND device id: 2c da 90 95 6 0 [ 2.143900@1] NAND device: Manufacturer ID: [ 2.147967@1] 0x2c, Chip ID: 0x2c (Micron A revision NAND 2Gib MT29F2G08-A) [ 2.155009@1] oob_fill_cnt =32 oob_size =64, bch_bytes =14 [ 2.160446@1] ecc mode:6 ecc_page_num=2 eep_need_oobsize=16 [ 2.166003@1] plane_num=1 writesize=0x800 ecc.size=0x200 bch_mode=1 [ 2.172235@1] mtd->oobavail: 0x8 [ 2.175748@1] aml_nand_init 2119: plat-name:nandnormal [ 2.180589@1] bbt_start=20 [ 2.183216@1] env_start=24 [ 2.185924@1] key_start=32 [ 2.188606@1] dtb_start=40 [ 2.191276@1] ddr_start=44 [ 2.193983@1] nbbt: info size=0x800 max_scan_blk=24, start_blk=20 [ 2.200475@1] get_free_node 43: bitmap=0 [ 2.203951@1] get_free_node 55: bitmap=1 [ 2.208042@1] get_free_node 43: bitmap=1 [ 2.211749@1] get_free_node 55: bitmap=3 [ 2.215841@1] get_free_node 43: bitmap=3 [ 2.219531@1] get_free_node 55: bitmap=7 [ 2.223450@1] nbbt : phy_blk_addr=20, ec=0, phy_page_addr=0, timestamp=1 [ 2.230120@1] nbbt free list: [ 2.233067@1] blockN=21, ec=-1, dirty_flag=0 [ 2.237313@1] blockN=22, ec=-1, dirty_flag=0 [ 2.241558@1] blockN=23, ec=-1, dirty_flag=0 [ 2.245808@1] aml_nand_scan_rsv_info 1141: page_num=1 [ 2.251219@1] nbbt valid addr: 280000 [ 2.254477@1] aml_nand_bbt_check 1306 bbt is valid, reading. [ 2.260109@1] aml_nand_read_rsv_info:423,read nbbt info at 280000 [ 2.266370@1] nenv: info size=0x10000 max_scan_blk=32, start_blk=24 [ 2.272799@1] get_free_node 43: bitmap=7 [ 2.276315@1] get_free_node 55: bitmap=f [ 2.280407@1] get_free_node 43: bitmap=f [ 2.284115@1] get_free_node 55: bitmap=1f [ 2.288294@1] get_free_node 43: bitmap=1f [ 2.292089@1] get_free_node 55: bitmap=3f [ 2.296268@1] get_free_node 43: bitmap=3f [ 2.300062@1] get_free_node 55: bitmap=7f [ 2.304241@1] get_free_node 43: bitmap=7f [ 2.308035@1] get_free_node 55: bitmap=ff [ 2.312214@1] get_free_node 43: bitmap=ff [ 2.316008@1] get_free_node 55: bitmap=1ff [ 2.320274@1] get_free_node 43: bitmap=1ff [ 2.324155@1] get_free_node 55: bitmap=3ff [ 2.328228@1] nenv : phy_blk_addr=24, ec=0, phy_page_addr=0, timestamp=1 [ 2.334899@1] nenv free list: [ 2.337847@1] blockN=25, ec=-1, dirty_flag=0 [ 2.342093@1] blockN=26, ec=-1, dirty_flag=0 [ 2.346340@1] blockN=27, ec=-1, dirty_flag=0 [ 2.350587@1] blockN=28, ec=-1, dirty_flag=0 [ 2.354833@1] blockN=29, ec=-1, dirty_flag=0 [ 2.359080@1] blockN=30, ec=-1, dirty_flag=0 [ 2.363326@1] blockN=31, ec=-1, dirty_flag=0 [ 2.367573@1] aml_nand_scan_rsv_info 1141: page_num=32 [ 2.384905@1] nenv valid addr: 310000 [ 2.384940@1] nkey: info size=0x8000 max_scan_blk=40, start_blk=32 [ 2.389297@1] get_free_node 43: bitmap=3ff [ 2.393177@1] get_free_node 55: bitmap=7ff [ 2.397442@1] get_free_node 43: bitmap=7ff [ 2.401323@1] get_free_node 55: bitmap=fff [ 2.405589@1] get_free_node 43: bitmap=fff [ 2.409470@1] get_free_node 55: bitmap=1fff [ 2.413822@1] get_free_node 43: bitmap=1fff [ 2.417790@1] get_free_node 55: bitmap=3fff [ 2.422142@1] get_free_node 43: bitmap=3fff [ 2.426110@1] get_free_node 55: bitmap=7fff [ 2.430462@1] get_free_node 43: bitmap=7fff [ 2.434430@1] get_free_node 55: bitmap=ffff [ 2.438780@1] get_free_node 43: bitmap=ffff [ 2.442750@1] get_free_node 55: bitmap=1ffff [ 2.447189@1] get_free_node 43: bitmap=1ffff [ 2.451243@1] get_free_node 55: bitmap=3ffff [ 2.455490@1] nkey : phy_blk_addr=-1, ec=0, phy_page_addr=0, timestamp=0 [ 2.462160@1] nkey free list: [ 2.465107@1] blockN=32, ec=-1, dirty_flag=0 [ 2.469354@1] blockN=33, ec=-1, dirty_flag=0 [ 2.473601@1] blockN=34, ec=-1, dirty_flag=0 [ 2.477848@1] blockN=35, ec=-1, dirty_flag=0 [ 2.482094@1] blockN=36, ec=-1, dirty_flag=0 [ 2.486341@1] blockN=37, ec=-1, dirty_flag=0 [ 2.490587@1] blockN=38, ec=-1, dirty_flag=0 [ 2.494834@1] blockN=39, ec=-1, dirty_flag=0 [ 2.499082@1] aml_nand_scan_rsv_info 1141: page_num=16 [ 2.504193@1] nkey valid addr: fffffffffffe0000 [ 2.508702@1] aml_nand_key_check 1251 NO key exist [ 2.513470@1] ndtb: info size=0x20000 max_scan_blk=44, start_blk=40 [ 2.520094@1] get_free_node 43: bitmap=3ffff [ 2.523956@1] get_free_node 55: bitmap=7ffff [ 2.528395@1] get_free_node 43: bitmap=7ffff [ 2.532450@1] get_free_node 55: bitmap=fffff [ 2.536888@1] get_free_node 43: bitmap=fffff [ 2.540943@1] get_free_node 55: bitmap=1fffff [ 2.545276@1] ndtb : phy_blk_addr=40, ec=0, phy_page_addr=0, timestamp=1 [ 2.551947@1] ndtb free list: [ 2.554878@1] blockN=41, ec=-1, dirty_flag=0 [ 2.559141@1] blockN=42, ec=-1, dirty_flag=0 [ 2.563388@1] blockN=43, ec=-1, dirty_flag=0 [ 2.567649@1] aml_nand_scan_rsv_info 1141: page_num=64 [ 2.584985@1] ndtb valid addr: 500000 [ 2.585018@1] nddr: info size=0x20000 max_scan_blk=46, start_blk=44 [ 2.589470@1] get_free_node 43: bitmap=1fffff [ 2.593611@1] get_free_node 55: bitmap=3fffff [ 2.598137@1] get_free_node 43: bitmap=3fffff [ 2.602277@1] get_free_node 55: bitmap=7fffff [ 2.606610@1] nddr : phy_blk_addr=-1, ec=0, phy_page_addr=0, timestamp=0 [ 2.613281@1] nddr free list: [ 2.616228@1] blockN=44, ec=-1, dirty_flag=0 [ 2.620475@1] blockN=45, ec=-1, dirty_flag=0 [ 2.624722@1] aml_nand_scan_rsv_info 1141: page_num=64 [ 2.629835@1] nddr valid addr: fffffffffffe0000 [ 2.634342@1] aml_nand_ddr_check 1281 NO ddr exist [ 2.639112@1] tpl: off 8388608, size 8388608 [ 2.704123@1] NAND bbt detect factory Bad block at 7fe0000 [ 2.704173@1] aml_nand_add_partition:394 factory bad addr=3ff [ 2.779283@1] Creating 6 MTD partitions on "nandnormal": [ 2.779331@1] 0x000000800000-0x000001000000 : "tpl" [ 2.790939@3] 0x000001000000-0x000001200000 : "misc" [ 2.794194@1] 0x000001200000-0x000002200000 : "recovery" [ 2.806344@0] 0x000002200000-0x000004200000 : "boot" [ 2.825858@0] 0x000004200000-0x000004700000 : "config" [ 2.830635@0] 0x000004700000-0x000010000000 : "nvdata" [ 2.861714@0] NAND bbt detect factory Bad block at 7fe0000 [ 2.933309@0] nandnormal initialized ok [ 2.933419@0] aml_ubootenv_init: register env chardev [ 2.936940@0] aml_ubootenv_init: register env chardev OK [ 2.941989@0] amlnf_dtb_init: register dtb cdev [ 2.946724@0] amlnf_dtb_init: register dtd cdev OK [ 2.951161@0] mtd_nand_probe 267 , err = 0 [ 2.956343@0] aml_vrtc rtc: rtc core: registered aml_vrtc as rtc0 [ 2.961728@0] input: aml_vkeypad as /devices/platform/rtc/input/input0 [ 2.968719@2] unifykey: storage in base: 0xffffffc005000000 [ 2.973350@2] unifykey: storage out base: 0xffffffc005040000 [ 2.978951@2] unifykey: storage block base: 0xffffffc005080000 [ 2.984755@2] unifykey: probe done! [ 2.988961@2] unifykey: no efuse-version set, use default value: -1 [ 2.994485@2] unifykey: key unify config unifykey-num is 6 [ 3.000096@2] unifykey: key unify fact unifykey-num is 6 [ 3.005218@2] unifykey: unifykey_devno: f200000 [ 3.010222@3] unifykey: device unifykeys created ok [ 3.014715@3] unifykey: aml_unifykeys_init done! [ 3.019608@3] sysled: module init [ 3.023110@3] meson_wdt ffd0f0d0.watchdog: start watchdog [ 3.027864@3] meson_wdt ffd0f0d0.watchdog: creat work queue for watch dog [ 3.035272@1] meson_wdt ffd0f0d0.watchdog: AML Watchdog Timer probed done [ 3.043980@2] dmc_monitor_probe [ 3.044875@2] page_trace_module_init, create sysfs failed [ 3.050693@2] defendkey defendkey: Reserved memory is not enough! [ 3.055952@2] defendkey: probe of defendkey failed with error -22 [ 3.062309@2] GACT probability NOT on [ 3.065679@2] Mirror/redirect action on [ 3.069453@2] u32 classifier [ 3.072287@2] Actions configured [ 3.075865@2] Netfilter messages via NETLINK v0.30. [ 3.081131@2] nf_conntrack version 0.5.0 (2048 buckets, 8192 max) [ 3.087337@2] ctnetlink v0.93: registering with nfnetlink. [ 3.093174@2] xt_time: kernel timezone is -0000 [ 3.096918@2] ipip: IPv4 and MPLS over IPv4 tunneling driver [ 3.103590@2] ip_tables: (C) 2000-2006 Netfilter Core Team [ 3.108291@2] arp_tables: arp_tables: (C) 2002 David S. Miller [ 3.113728@2] Initializing XFRM netlink socket [ 3.119288@2] NET: Registered protocol family 10 [ 3.125239@2] mip6: Mobile IPv6 [ 3.125793@2] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 3.131811@2] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 3.139887@2] NET: Registered protocol family 17 [ 3.142002@2] NET: Registered protocol family 15 [ 3.146642@2] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 3.159814@2] l2tp_core: L2TP core driver, V2.0 [ 3.164176@2] l2tp_ppp: PPPoL2TP kernel driver, V2.0 [ 3.169102@2] l2tp_ip: L2TP IP encapsulation support (L2TPv3) [ 3.174847@2] l2tp_netlink: L2TP netlink interface [ 3.179681@2] l2tp_eth: L2TP ethernet pseudowire support (L2TPv3) [ 3.185722@2] l2tp_debugfs: L2TP debugfs support [ 3.190245@2] l2tp_ip6: L2TP IP encapsulation support for IPv6 (L2TPv3) [ 3.196913@2] NET: Registered protocol family 35 [ 3.201840@2] Key type dns_resolver registered [ 3.206417@2] Registered swp emulation handler [ 3.210372@2] Registered cp15_barrier emulation handler [ 3.215543@2] Registered setend emulation handler [ 3.220223@2] disable EAS feature [ 3.224917@3] registered taskstats version 1 [ 3.241918@2] dwc3 ff500000.dwc3: Configuration mismatch. dr_mode forced to host [ 3.748448@2] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 3.748536@2] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 [ 3.756870@2] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f664 hci version 0x100 quirks 0x02010010 [ 3.765262@2] xhci-hcd xhci-hcd.0.auto: irq 22, io mem 0xff500000 [ 3.772785@1] hub 1-0:1.0: USB hub found [ 3.775150@1] hub 1-0:1.0: 1 port detected [ 3.779888@1] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 3.784834@1] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 [ 3.792746@1] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 3.802248@2] hub 2-0:1.0: USB hub found [ 3.804827@2] hub 2-0:1.0: config failed, hub doesn't have any ports! (err -19) [ 3.812115@2] usb usb2: Unsupported the hub [ 3.816882@2] aml_vrtc rtc: setting system clock to 2021-12-29 20:02:24 UTC (1640808144) [ 3.824957@2] dwc_otg ff400000.dwc2_a: dwc_otg_driver_probe(ffffffc00e1a3000) [ 3.825033@2] dwc_otg: usb0: type: 2 speed: 0, config: 0, dma: 0, id: 0, phy: ffe09000, ctrl: 0 [ 3.832939@2] dwc_otg ff400000.dwc2_a: base=0xffffff8008580000 [ 3.832952@2] dwc_otg ff400000.dwc2_a: dwc_otg_device=0xffffffc00c3ab600 [ 3.933393@1] dwc_otg: Core Release: 3.10a [ 3.933451@1] dwc_otg: Setting default values for core params [ 3.937639@1] dwc_otg: curmode: 0, host_only: 0 [ 3.942148@1] dwc_otg ff400000.dwc2_a: DMA config: BURST_DEFAULT [ 3.954691@1] dwc_otg: Using Buffer DMA mode [ 3.954729@1] dwc_otg: OTG VER PARAM: 1, OTG VER FLAG: 1 [ 3.958637@1] dwc_otg: Working on port type = SLAVE [ 3.963494@1] dwc_otg: Dedicated Tx FIFOs mode [ 3.970590@0] thermal thermal_zone0: binding zone soc_thermal with cdev thermal-cpufreq-0 failed:-22 [ 3.977212@0] cpucore_cooling_register, max_cpu_core_num:4 [ 3.989813@0] gxbb_pm: enter meson_pm_probe! [ 3.989869@0] no vddio3v3_en pin [ 3.991517@0] pm-meson aml_pm: Can't get switch_clk81 [ 3.996648@0] gxbb_pm: meson_pm_probe done [ 4.001559@0] meson_uart ff803000.serial: ttyS0 use xtal(24M) 24000000 change 115200 to 115200 [ 4.007938@0] Freeing unused kernel memory: 3648K [ 4.023097@0] meson_uart ff803000.serial: ttyS0 use xtal(24M) 24000000 change 115200 to 115200 [ 4.281826@2] ubi0: attaching mtd5 [ 4.300725@2] ubi0: scanning is finished [ 4.305349@2] ubi0: attached mtd5 (name "config", size 5 MiB) [ 4.305477@2] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 4.312537@2] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 4.319454@2] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 4.326550@2] ubi0: good PEBs: 40, bad PEBs: 0, corrupted PEBs: 0 [ 4.332622@2] ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128 [ 4.339981@2] ubi0: max/mean erase counter: 4/2, WL threshold: 4096, image sequence number: 1929412561 [ 4.349261@2] ubi0: available PEBs: 0, total reserved PEBs: 40, PEBs reserved for bad PEB handling: 4 [ 4.358461@3] ubi0: background thread "ubi_bgt0d" started, PID 1076 [ 4.371725@2] UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 1080 [ 4.409658@1] UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "config_data" [ 4.412088@1] UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 4.422116@1] UBIFS (ubi0:0): FS size: 2793472 bytes (2 MiB, 22 LEBs), journal size 1015809 bytes (0 MiB, 6 LEBs) [ 4.432334@1] UBIFS (ubi0:0): reserved for root: 131942 bytes (128 KiB) [ 4.438922@1] UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID 6FC5229C-4866-4B92-B42B-5491106989DF, small LPT model [ 4.463729@2] ubi2: attaching mtd6 [ 4.673091@2] NAND bbt detect factory Bad block at 7fe0000 [ 5.143234@2] ubi2: scanning is finished [ 5.150453@2] ubi2: attached mtd6 (name "nvdata", size 185 MiB) [ 5.150754@2] ubi2: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 5.157808@2] ubi2: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 5.164729@2] ubi2: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 5.171824@2] ubi2: good PEBs: 1479, bad PEBs: 1, corrupted PEBs: 0 [ 5.178071@2] ubi2: user volume: 1, internal volumes: 1, max. volumes count: 128 [ 5.185432@2] ubi2: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 2603558039 [ 5.194712@2] ubi2: available PEBs: 0, total reserved PEBs: 1479, PEBs reserved for bad PEB handling: 3 [ 5.204089@3] ubi2: background thread "ubi_bgt2d" started, PID 1088 [ 5.217419@1] UBIFS (ubi2:0): background thread "ubifs_bgt2_0" started, PID 1092 [ 5.249967@0] UBIFS (ubi2:0): UBIFS: mounted UBI device 2, volume 0, name "nvdata_data" [ 5.252414@0] UBIFS (ubi2:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 5.262424@0] UBIFS (ubi2:0): FS size: 185384960 bytes (176 MiB, 1460 LEBs), journal size 9269248 bytes (8 MiB, 73 LEBs) [ 5.273259@0] UBIFS (ubi2:0): reserved for root: 4952683 bytes (4836 KiB) [ 5.280014@0] UBIFS (ubi2:0): media format: w4/r0 (latest is w4/r0), UUID E385CDEE-0F47-4349-B466-78F7D3A5F35B, small LPT model [ 5.501093@0] eth0: device MAC address 02:15:f5:c6:77:f0 [ 5.584569@2] meson6-dwmac ff3f0000.ethernet eth0: fail to init PTP. [ 5.585861@2] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 5.804022@1] uart_trans: loading out-of-tree module taints kernel. [ 5.806304@1] register uart_trans chrdev success. [ 5.809951@1] meson_uart ff804000.serial: ttyS3 use xtal(24M) 24000000 change 0 to 9600 [ 5.817503@1] tty port open success [/dev/ttyS3]! [ 5.822045@1] meson_uart ff804000.serial: ttyS3 use xtal(24M) 24000000 change 9600 to 115200 [ 5.830453@1] init sucess for tty struct (246:3) [/dev/ttyS3] [ 5.836582@1] meson_uart ffd23000.serial: ttyS2 use xtal(24M) 24000000 change 0 to 9600 [ 5.844232@1] tty port open success [/dev/ttyS2]! [ 5.848898@1] meson_uart ffd23000.serial: ttyS2 use xtal(24M) 24000000 change 9600 to 115200 [ 5.857311@1] init sucess for tty struct (246:2) [/dev/ttyS2] [ 5.863404@1] meson_uart ffd24000.serial: ttyS1 use xtal(24M) 24000000 change 0 to 9600 [ 5.871101@1] tty port open success [/dev/ttyS1]! [ 5.875765@1] meson_uart ffd24000.serial: ttyS1 use xtal(24M) 24000000 change 9600 to 115200 [ 5.884171@1] init sucess for tty struct (246:1) [/dev/ttyS1] [ 5.890514@2] create workqueue success! [ 7.635974@2] meson6-dwmac ff3f0000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx [ 7.639265@2] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 19.016235@0] uart trans dev open. [ 19.016346@0] uart_buf virt addr = 0xffffffc00bd00000 [ 19.019128@0] uart_buf phys addr = 0x0bd00000 [ 19.023483@0] uart_buf pfn = 0x0000bd00 [ 19.028151@0] uart trans stop send work timer. [ 19.032435@0] uart trans set chain exist bits:0x7. [ 19.037012@0] uart trans set work queue count 768. [ 59.082195@0] nf_conntrack: default automatic helper assignment has been turned off for security reasons and CT-based firewall rule not found. Use the iptables CT target to attach helpers instead. [ 69.058524@2] uart set baud to: 4098 [ 69.058584@2] uart set baud to: 4098 [ 69.060185@1] uart set baud to: 4098 [ 109.436314@1] meson_uart ff804000.serial: ttyS3 use xtal(24M) 24000000 change 115200 to 3000000 [ 109.439395@1] uart set baud to: 4109 [ 109.503288@1] meson_uart ffd23000.serial: ttyS2 use xtal(24M) 24000000 change 115200 to 3000000 [ 109.506416@1] uart set baud to: 4109 [ 109.570471@2] meson_uart ffd24000.serial: ttyS1 use xtal(24M) 24000000 change 115200 to 3000000 [ 109.573612@2] uart set baud to: 4109 [ 147.441360@1] uart trans start send work timer. [ 177.187688@1] hrtimer: interrupt took 49542 ns
===========================================Miner log=========================================== 2021-12-29 20:02:31 Miner compile time: Wed Oct 20 17:50:59 CST 2021 type: Antminer S19 2021-12-29 20:02:32 This is fix-freq version 2021-12-29 20:02:32 Miner compile time: Wed Oct 20 17:50:59 CST 2021 type: Antminer S19 2021-12-29 20:02:32 commit version: ce69be1 2021-10-19 19:57:55, build by: jenkins 2021-10-20 18:33:58 2021-12-29 20:02:32 opt_multi_version = 1 2021-12-29 20:02:32 opt_bitmain_ab = 1 2021-12-29 20:02:32 mid_auto_gen = 1 2021-12-29 20:02:32 opt_bitmain_work_mode = 0 2021-12-29 20:02:32 port 439 already exported 2021-12-29 20:02:32 port 454 already exported 2021-12-29 20:02:32 port 440 already exported 2021-12-29 20:02:32 port 455 already exported 2021-12-29 20:02:32 port 441 already exported 2021-12-29 20:02:32 port 456 already exported 2021-12-29 20:02:32 port 438 already exported 2021-12-29 20:02:32 port 453 already exported 2021-12-29 20:02:32 port 446 already exported 2021-12-29 20:02:32 port 445 already exported 2021-12-29 20:02:32 Note: front fan is power on! 2021-12-29 20:02:32 Note: rear fan is power on! 2021-12-29 20:02:32 start the http log. 2021-12-29 20:02:32 httpListenThread start ret=0 2021-12-29 20:02:32 start listen on 6060 ... 2021-12-29 20:02:32 load machine BHB42801 conf 2021-12-29 20:02:32 machine : BHB42801 2021-12-29 20:02:32 chain_num 4, chain_domain_num 44, chain_asic_num 88, domain_asic_num 2 2021-12-29 20:02:32 bad chain id = 3 2021-12-29 20:02:35 bad chain id = 3 2021-12-29 20:02:37 ==========================capability start========================== 2021-12-29 20:02:37 board num = 3 2021-12-29 20:02:37 board id = 0, chain num = 1 2021-12-29 20:02:37 chain id = 0 2021-12-29 20:02:37 board id = 1, chain num = 1 2021-12-29 20:02:37 chain id = 1 2021-12-29 20:02:37 board id = 2, chain num = 1 2021-12-29 20:02:37 chain id = 2 2021-12-29 20:02:37 ==========================capability end============================ 2021-12-29 20:02:37 chain num = 3 2021-12-29 20:02:38 load chain 0 eeprom data 2021-12-29 20:02:39 load chain 1 eeprom data 2021-12-29 20:02:40 load chain 2 eeprom data 2021-12-29 20:02:40 fan_eft : 0 fan_pwm : 100 2021-12-29 20:02:40 create thread get_nonce_and_register_thread 2021-12-29 20:02:40 fixed working voltage = 1580 2021-12-29 20:02:40 Chain [0] PCB Version: 0x0110 2021-12-29 20:02:40 Chain [0] BOM Version: 0x0010 2021-12-29 20:02:40 Chain [1] PCB Version: 0x0110 2021-12-29 20:02:40 Chain [1] BOM Version: 0x0010 2021-12-29 20:02:40 Chain [2] PCB Version: 0x0110 2021-12-29 20:02:40 Chain [2] BOM Version: 0x0010 2021-12-29 20:02:40 bad chain id = 3 2021-12-29 20:02:40 Fan check passed. 2021-12-29 20:02:40 uart_trans addr:0xf6e0b000. 2021-12-29 20:02:41 chain[0] PIC jump to app 2021-12-29 20:02:43 Check chain[0] PIC fw version=0x89 2021-12-29 20:02:44 chain[1] PIC jump to app 2021-12-29 20:02:45 Check chain[1] PIC fw version=0x89 2021-12-29 20:02:46 chain[2] PIC jump to app 2021-12-29 20:02:48 Check chain[2] PIC fw version=0x89 2021-12-29 20:02:48 create thread pic_heart_beat_thread 2021-12-29 20:02:48 max sensor num = 4 2021-12-29 20:02:48 STATUS_INITED: soc init done! 2021-12-29 20:02:48 temperature_monitor_thread start... 2021-12-29 20:02:50 start to init... 2021-12-29 20:02:50 i2c_sim_init start 2021-12-29 20:02:50 init gpio477 2021-12-29 20:02:50 init gpio476 2021-12-29 20:02:50 i2c_sim_init end 2021-12-29 20:02:52 power open power_version = 0x73 2021-12-29 20:02:53 power type version: 0x0073 2021-12-29 20:02:53 Enter sleep to make sure power release finish. 2021-12-29 20:03:24 Slept 30 seconds, diff = 0. 2021-12-29 20:03:25 set_voltage_by_steps to 1700. 2021-12-29 20:03:28 chain avg vol rise to 16.80 2021-12-29 20:03:30 start up min temp by 75a = 26 2021-12-29 20:03:41 Chain[0]: find 88 asic, times 0 2021-12-29 20:03:51 Chain[1]: find 88 asic, times 0 2021-12-29 20:04:01 Chain[2]: find 88 asic, times 0 2021-12-29 20:04:06 pulse_mode = 1, ccdly_sel = 0, pwth_sel = 1 2021-12-29 20:04:11 min freq in eeprom = 675 2021-12-29 20:04:11 fixed frequency is 675 2021-12-29 20:04:11 Bring up temperature is 26 2021-12-29 20:04:11 set UART baud to 3000000 2021-12-29 20:04:11 create thread check_miner_status_thread 2021-12-29 20:04:11 create thread check_system_work_thread 2021-12-29 20:04:11 set_voltage_by_steps to 1650. 2021-12-29 20:04:13 fixed step freq_start = 50, freq_end = 675, freq_step = 6.25 2021-12-29 20:04:13 chain = 0 set freq to 56.25 2021-12-29 20:04:13 chain = 1 set freq to 56.25 2021-12-29 20:04:13 chain = 2 set freq to 56.25 2021-12-29 20:04:13 chain = 0 set freq to 62.50 2021-12-29 20:04:13 chain = 1 set freq to 62.50 2021-12-29 20:04:13 chain = 2 set freq to 62.50 2021-12-29 20:04:14 chain = 0 set freq to 68.75 2021-12-29 20:04:14 chain = 1 set freq to 68.75 2021-12-29 20:04:14 chain = 2 set freq to 68.75 2021-12-29 20:04:14 chain = 0 set freq to 75.00 2021-12-29 20:04:14 chain = 1 set freq to 75.00 2021-12-29 20:04:14 chain = 2 set freq to 75.00 2021-12-29 20:04:14 chain = 0 set freq to 81.25 2021-12-29 20:04:14 chain = 1 set freq to 81.25 2021-12-29 20:04:14 chain = 2 set freq to 81.25 2021-12-29 20:04:14 chain = 0 set freq to 87.50 2021-12-29 20:04:14 chain = 1 set freq to 87.50 2021-12-29 20:04:14 chain = 2 set freq to 87.50 2021-12-29 20:04:14 chain = 0 set freq to 93.75 2021-12-29 20:04:14 chain = 1 set freq to 93.75 2021-12-29 20:04:14 chain = 2 set freq to 93.75 2021-12-29 20:04:14 chain = 0 set freq to 100.00 2021-12-29 20:04:14 chain = 1 set freq to 100.00 2021-12-29 20:04:14 chain = 2 set freq to 100.00 2021-12-29 20:04:14 chain = 0 set freq to 106.25 2021-12-29 20:04:14 chain = 1 set freq to 106.25 2021-12-29 20:04:14 chain = 2 set freq to 106.25 2021-12-29 20:04:14 chain = 0 set freq to 112.50 2021-12-29 20:04:14 chain = 1 set freq to 112.50 2021-12-29 20:04:14 chain = 2 set freq to 112.50 2021-12-29 20:04:14 chain = 0 set freq to 118.75 2021-12-29 20:04:14 chain = 1 set freq to 118.75 2021-12-29 20:04:14 chain = 2 set freq to 118.75 2021-12-29 20:04:14 chain = 0 set freq to 125.00 2021-12-29 20:04:14 chain = 1 set freq to 125.00 2021-12-29 20:04:14 chain = 2 set freq to 125.00 2021-12-29 20:04:15 chain = 0 set freq to 131.25 2021-12-29 20:04:15 chain = 1 set freq to 131.25 2021-12-29 20:04:15 chain = 2 set freq to 131.25 2021-12-29 20:04:15 chain = 0 set freq to 137.50 2021-12-29 20:04:15 chain = 1 set freq to 137.50 2021-12-29 20:04:15 chain = 2 set freq to 137.50 2021-12-29 20:04:15 chain = 0 set freq to 143.75 2021-12-29 20:04:15 chain = 1 set freq to 143.75 2021-12-29 20:04:15 chain = 2 set freq to 143.75 2021-12-29 20:04:15 chain = 0 set freq to 150.00 2021-12-29 20:04:15 chain = 1 set freq to 150.00 2021-12-29 20:04:15 chain = 2 set freq to 150.00 2021-12-29 20:04:15 chain = 0 set freq to 156.25 2021-12-29 20:04:15 chain = 1 set freq to 156.25 2021-12-29 20:04:15 chain = 2 set freq to 156.25 2021-12-29 20:04:15 chain = 0 set freq to 162.50 2021-12-29 20:04:15 chain = 1 set freq to 162.50 2021-12-29 20:04:15 chain = 2 set freq to 162.50 2021-12-29 20:04:15 chain = 0 set freq to 168.75 2021-12-29 20:04:15 chain = 1 set freq to 168.75 2021-12-29 20:04:15 chain = 2 set freq to 168.75 2021-12-29 20:04:15 chain = 0 set freq to 175.00 2021-12-29 20:04:15 chain = 1 set freq to 175.00 2021-12-29 20:04:15 chain = 2 set freq to 175.00 2021-12-29 20:04:15 chain = 0 set freq to 181.25 2021-12-29 20:04:15 chain = 1 set freq to 181.25 2021-12-29 20:04:15 chain = 2 set freq to 181.25 2021-12-29 20:04:15 chain = 0 set freq to 187.50 2021-12-29 20:04:15 chain = 1 set freq to 187.50 2021-12-29 20:04:15 chain = 2 set freq to 187.50 2021-12-29 20:04:16 chain = 0 set freq to 193.75 2021-12-29 20:04:16 chain = 1 set freq to 193.75 2021-12-29 20:04:16 chain = 2 set freq to 193.75 2021-12-29 20:04:16 chain = 0 set freq to 200.00 2021-12-29 20:04:16 chain = 1 set freq to 200.00 2021-12-29 20:04:16 chain = 2 set freq to 200.00 2021-12-29 20:04:16 chain = 0 set freq to 206.25 2021-12-29 20:04:16 chain = 1 set freq to 206.25 2021-12-29 20:04:16 chain = 2 set freq to 206.25 2021-12-29 20:04:16 chain = 0 set freq to 212.50 2021-12-29 20:04:16 chain = 1 set freq to 212.50 2021-12-29 20:04:16 chain = 2 set freq to 212.50 2021-12-29 20:04:16 chain = 0 set freq to 218.75 2021-12-29 20:04:16 chain = 1 set freq to 218.75 2021-12-29 20:04:16 chain = 2 set freq to 218.75 2021-12-29 20:04:16 chain = 0 set freq to 225.00 2021-12-29 20:04:16 chain = 1 set freq to 225.00 2021-12-29 20:04:16 chain = 2 set freq to 225.00 2021-12-29 20:04:16 chain = 0 set freq to 231.25 2021-12-29 20:04:16 chain = 1 set freq to 231.25 2021-12-29 20:04:16 chain = 2 set freq to 231.25 2021-12-29 20:04:16 chain = 0 set freq to 237.50 2021-12-29 20:04:16 chain = 1 set freq to 237.50 2021-12-29 20:04:16 chain = 2 set freq to 237.50 2021-12-29 20:04:16 chain = 0 set freq to 243.75 2021-12-29 20:04:16 chain = 1 set freq to 243.75 2021-12-29 20:04:16 chain = 2 set freq to 243.75 2021-12-29 20:04:17 chain = 0 set freq to 250.00 2021-12-29 20:04:17 chain = 1 set freq to 250.00 2021-12-29 20:04:17 chain = 2 set freq to 250.00 2021-12-29 20:04:17 chain = 0 set freq to 256.25 2021-12-29 20:04:17 chain = 1 set freq to 256.25 2021-12-29 20:04:17 chain = 2 set freq to 256.25 2021-12-29 20:04:17 chain = 0 set freq to 262.50 2021-12-29 20:04:17 chain = 1 set freq to 262.50 2021-12-29 20:04:17 chain = 2 set freq to 262.50 2021-12-29 20:04:17 chain = 0 set freq to 268.75 2021-12-29 20:04:17 chain = 1 set freq to 268.75 2021-12-29 20:04:17 chain = 2 set freq to 268.75 2021-12-29 20:04:17 chain = 0 set freq to 275.00 2021-12-29 20:04:17 chain = 1 set freq to 275.00 2021-12-29 20:04:17 chain = 2 set freq to 275.00 2021-12-29 20:04:17 chain = 0 set freq to 281.25 2021-12-29 20:04:17 chain = 1 set freq to 281.25 2021-12-29 20:04:17 chain = 2 set freq to 281.25 2021-12-29 20:04:17 chain = 0 set freq to 287.50 2021-12-29 20:04:17 chain = 1 set freq to 287.50 2021-12-29 20:04:17 chain = 2 set freq to 287.50 2021-12-29 20:04:17 chain = 0 set freq to 293.75 2021-12-29 20:04:17 chain = 1 set freq to 293.75 2021-12-29 20:04:17 chain = 2 set freq to 293.75 2021-12-29 20:04:17 chain = 0 set freq to 300.00 2021-12-29 20:04:17 chain = 1 set freq to 300.00 2021-12-29 20:04:17 chain = 2 set freq to 300.00 2021-12-29 20:04:17 chain = 0 set freq to 306.25 2021-12-29 20:04:17 chain = 1 set freq to 306.25 2021-12-29 20:04:17 chain = 2 set freq to 306.25 2021-12-29 20:04:18 chain = 0 set freq to 312.50 2021-12-29 20:04:18 chain = 1 set freq to 312.50 2021-12-29 20:04:18 chain = 2 set freq to 312.50 2021-12-29 20:04:18 chain = 0 set freq to 318.75 2021-12-29 20:04:18 chain = 1 set freq to 318.75 2021-12-29 20:04:18 chain = 2 set freq to 318.75 2021-12-29 20:04:18 chain = 0 set freq to 325.00 2021-12-29 20:04:18 chain = 1 set freq to 325.00 2021-12-29 20:04:18 chain = 2 set freq to 325.00 2021-12-29 20:04:18 chain = 0 set freq to 331.25 2021-12-29 20:04:18 chain = 1 set freq to 331.25 2021-12-29 20:04:18 chain = 2 set freq to 331.25 2021-12-29 20:04:18 chain = 0 set freq to 337.50 2021-12-29 20:04:18 chain = 1 set freq to 337.50 2021-12-29 20:04:18 chain = 2 set freq to 337.50 2021-12-29 20:04:18 chain = 0 set freq to 343.75 2021-12-29 20:04:18 chain = 1 set freq to 343.75 2021-12-29 20:04:18 chain = 2 set freq to 343.75 2021-12-29 20:04:18 chain = 0 set freq to 350.00 2021-12-29 20:04:18 chain = 1 set freq to 350.00 2021-12-29 20:04:18 chain = 2 set freq to 350.00 2021-12-29 20:04:18 chain = 0 set freq to 356.25 2021-12-29 20:04:18 chain = 1 set freq to 356.25 2021-12-29 20:04:18 chain = 2 set freq to 356.25 2021-12-29 20:04:18 chain = 0 set freq to 362.50 2021-12-29 20:04:18 chain = 1 set freq to 362.50 2021-12-29 20:04:18 chain = 2 set freq to 362.50 2021-12-29 20:04:18 chain = 0 set freq to 368.75 2021-12-29 20:04:18 chain = 1 set freq to 368.75 2021-12-29 20:04:18 chain = 2 set freq to 368.75 2021-12-29 20:04:19 chain = 0 set freq to 375.00 2021-12-29 20:04:19 chain = 1 set freq to 375.00 2021-12-29 20:04:19 chain = 2 set freq to 375.00 2021-12-29 20:04:19 chain = 0 set freq to 381.25 2021-12-29 20:04:19 chain = 1 set freq to 381.25 2021-12-29 20:04:19 chain = 2 set freq to 381.25 2021-12-29 20:04:19 chain = 0 set freq to 387.50 2021-12-29 20:04:19 chain = 1 set freq to 387.50 2021-12-29 20:04:19 chain = 2 set freq to 387.50 2021-12-29 20:04:19 chain = 0 set freq to 393.75 2021-12-29 20:04:19 chain = 1 set freq to 393.75 2021-12-29 20:04:19 chain = 2 set freq to 393.75 2021-12-29 20:04:19 chain = 0 set freq to 400.00 2021-12-29 20:04:19 chain = 1 set freq to 400.00 2021-12-29 20:04:19 chain = 2 set freq to 400.00 2021-12-29 20:04:19 chain = 0 set freq to 406.25 2021-12-29 20:04:19 chain = 1 set freq to 406.25 2021-12-29 20:04:19 chain = 2 set freq to 406.25 2021-12-29 20:04:19 chain = 0 set freq to 412.50 2021-12-29 20:04:19 chain = 1 set freq to 412.50 2021-12-29 20:04:19 chain = 2 set freq to 412.50 2021-12-29 20:04:19 chain = 0 set freq to 418.75 2021-12-29 20:04:19 chain = 1 set freq to 418.75 2021-12-29 20:04:19 chain = 2 set freq to 418.75 2021-12-29 20:04:19 chain = 0 set freq to 425.00 2021-12-29 20:04:19 chain = 1 set freq to 425.00 2021-12-29 20:04:19 chain = 2 set freq to 425.00 2021-12-29 20:04:19 chain = 0 set freq to 431.25 2021-12-29 20:04:19 chain = 1 set freq to 431.25 2021-12-29 20:04:19 chain = 2 set freq to 431.25 2021-12-29 20:04:20 chain = 0 set freq to 437.50 2021-12-29 20:04:20 chain = 1 set freq to 437.50 2021-12-29 20:04:20 chain = 2 set freq to 437.50 2021-12-29 20:04:20 chain = 0 set freq to 443.75 2021-12-29 20:04:20 chain = 1 set freq to 443.75 2021-12-29 20:04:20 chain = 2 set freq to 443.75 2021-12-29 20:04:20 chain = 0 set freq to 450.00 2021-12-29 20:04:20 chain = 1 set freq to 450.00 2021-12-29 20:04:20 chain = 2 set freq to 450.00 2021-12-29 20:04:20 chain = 0 set freq to 456.25 2021-12-29 20:04:20 chain = 1 set freq to 456.25 2021-12-29 20:04:20 chain = 2 set freq to 456.25 2021-12-29 20:04:20 chain = 0 set freq to 462.50 2021-12-29 20:04:20 chain = 1 set freq to 462.50 2021-12-29 20:04:20 chain = 2 set freq to 462.50 2021-12-29 20:04:20 chain = 0 set freq to 468.75 2021-12-29 20:04:20 chain = 1 set freq to 468.75
|