Antminer S1: No devices detected!

[xref]

Hello

am unable to have my newly recieved antminer running

Cant find Cgminer on the processes, so i went to ssh and did enter the following
cgminer -o stratum+tcp://stratum.mining.eligius.st:3334 -u 1DiBRqnfKV7eSekycQ7VHVoZSzxG1nGSRW -p x

i got 2 errors
first one, No devices detected
second one, No servers could be used!

how the hell am gonna fix this

the other thing, isn't the board should be lighting with green, both boards got 0 light, only the ethernet board i see its light
i also do not hear any beeping at all like others dose.

dunno how the hell am gonna fix this shit

here is my kernel:

Code:

[    0.000000] Linux version 3.10.12 (xxl@ubuntu) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2013.05 r38031) ) #2 Fri Feb 7 18:50:12 CST 2014
[    0.000000] MyLoader: sysp=1bec2fee, boardp=fdd6ef6f, parts=fc031564
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 00019374 (MIPS 24Kc)
[    0.000000] SoC: Atheros AR9330 rev 1
[    0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x03ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x03ffffff]
[    0.000000] On node 0 totalpages: 16384
[    0.000000] free_area_init_node: node 0, pgdat 803005b0, node_mem_map 81000000
[    0.000000]   Normal zone: 128 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 16384 pages, LIFO batch:3
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0 
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line:  board=TL-WR741ND-v4 console=ttyATH0,115200 rootfstype=squashfs,jffs2 noinitrd
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 61336k/65536k available (2187k kernel code, 4200k reserved, 588k data, 232k init, 0k highmem)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:51
[    0.080000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
[    0.080000] pid_max: default: 32768 minimum: 301
[    0.080000] Mount-cache hash table entries: 512
[    0.090000] NET: Registered protocol family 16
[    0.100000] MIPS: machine is TP-LINK TL-WR741ND v4
[    0.550000] bio: create slab <bio-0> at 0
[    0.560000] Switching to clocksource MIPS
[    0.560000] NET: Registered protocol family 2
[    0.570000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[    0.570000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[    0.570000] TCP: Hash tables configured (established 512 bind 512)
[    0.580000] TCP: reno registered
[    0.580000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.590000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.600000] NET: Registered protocol family 1
[    0.600000] PCI: CLS 0 bytes, default 32
[    0.620000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.620000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.630000] msgmni has been set to 119
[    0.630000] io scheduler noop registered
[    0.640000] io scheduler deadline registered (default)
[    0.640000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[    0.650000] ar933x-uart: ttyATH0 at MMIO 0x18020000 (irq = 11) is a AR933X UART
[    0.660000] console [ttyATH0] enabled, bootconsole disabled
[    0.670000] ath79-spi ath79-spi: master is unqueued, this is deprecated
[    0.680000] m25p80 spi0.0: found s25fl064k, expected m25p80
[    0.680000] m25p80 spi0.0: s25fl064k (8192 Kbytes)
[    0.690000] 5 tp-link partitions found on MTD device spi0.0
[    0.690000] Creating 5 MTD partitions on "spi0.0":
[    0.700000] 0x000000000000-0x000000020000 : "u-boot"
[    0.700000] 0x000000020000-0x000000117d84 : "kernel"
[    0.710000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.720000] 0x000000117d84-0x0000007f0000 : "rootfs"
[    0.720000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.740000] mtd: partition "rootfs" set to be root filesystem
[    0.740000] mtd: partition "rootfs_data" created automatically, ofs=0x370000, len=0x480000
[    0.750000] 0x000000370000-0x0000007f0000 : "rootfs_data"
[    0.760000] 0x000000020000-0x0000007f0000 : "firmware"
[    0.760000] 0x0000007f0000-0x000000800000 : "art"
[    0.780000] libphy: ag71xx_mdio: probed
[    0.790000] eth0: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
[    1.340000] eth0: Found an AR7240/AR9330 built-in switch
[    2.380000] eth1: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
[    2.930000] ag71xx ag71xx.0 eth1: connected to PHY at ag71xx-mdio.1:04 [uid=004dd041, driver=Generic PHY]
[    2.940000] TCP: cubic registered
[    2.940000] NET: Registered protocol family 17
[    2.950000] 8021q: 802.1Q VLAN Support v1.8
[    2.960000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    2.970000] Freeing unused kernel memory: 232K (80316000 - 80350000)
[    5.800000] usbcore: registered new interface driver usbfs
[    5.800000] usbcore: registered new interface driver hub
[    5.810000] usbcore: registered new device driver usb
[    5.810000] usbcore: registered new interface driver bitmain
[    5.820000] hash ok
[    5.820000] hashtest OK
[    5.820000] bitmain-asic: success to register device
[    5.830000] usbcore: registered new interface driver bitmainbl
[    5.840000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    5.850000] ehci-platform: EHCI generic platform driver
[    5.850000] ehci-platform ehci-platform: EHCI Host Controller
[    5.860000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[    5.860000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[    5.890000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[    5.890000] hub 1-0:1.0: USB hub found
[    5.890000] hub 1-0:1.0: 1 port detected
[    6.230000] usb 1-1: new high-speed USB device number 2 using ehci-platform
[    6.380000] hub 1-1:1.0: USB hub found
[    6.380000] hub 1-1:1.0: 2 ports detected
[    6.670000] usb 1-1.1: new full-speed USB device number 3 using ehci-platform
[    6.800000] bitmain 1-1.1:1.0: USB Bitmain asic device now attached to USB Bitmain asic-0
[    6.810000] PIC microchip usb OK
[   10.560000] jffs2: notice: (328) jffs2_build_xattr_subsystem: complete building xattr subsystem, 25 of xdatum (0 unchecked, 24 orphan) and 40 of xref (0 dead, 24 orphan) found.
[   12.820000] hidraw: raw HID events driver (C) Jiri Kosina
[   12.830000] Loading modules backported from Linux version master-2013-06-27-0-gdcfa6d5
[   12.830000] Backport generated by backports.git backports-20130617-4-ge3220f5
[   12.850000] nf_conntrack version 0.5.0 (962 buckets, 3848 max)
[   12.870000] usbcore: registered new interface driver usbhid
[   12.880000] usbhid: USB HID core driver
[   12.890000] usbcore: registered new interface driver usbserial
[   12.890000] usbcore: registered new interface driver usbserial_generic
[   12.900000] usbserial: USB Serial support registered for generic
[   12.930000] xt_time: kernel timezone is -0000
[   12.960000] cfg80211: Calling CRDA to update world regulatory domain
[   12.960000] cfg80211: World regulatory domain updated:
[   12.970000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   12.970000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   12.980000] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   12.990000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   13.000000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   13.000000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   13.020000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   13.160000] ath: EEPROM regdomain: 0x0
[   13.160000] ath: EEPROM indicates default country code should be used
[   13.160000] ath: doing EEPROM country->regdmn map search
[   13.160000] ath: country maps to regdmn code: 0x3a
[   13.160000] ath: Country alpha2 being used: US
[   13.160000] ath: Regpair used: 0x3a
[   13.160000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[   13.180000] cfg80211: Calling CRDA for country: US
[   13.180000] cfg80211: Regulatory domain changed to country: US
[   13.190000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   13.200000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
[   13.210000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
[   13.210000] cfg80211:   (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   13.220000] cfg80211:   (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   13.230000] cfg80211:   (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   13.240000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
[   13.250000] ieee80211 phy0: Atheros AR9330 Rev:1 mem=0xb8100000, irq=2
[   18.030000] device eth0 entered promiscuous mode
[   20.300000] eth1: link up (100Mbps/Full duplex)
[   24.300000] usb 1-1.1: USB disconnect, device number 3
[   24.310000] bitmain 1-1.1:1.0: USB Bitmain asic #0 now disconnected
[   24.570000] usb 1-1.1: new full-speed USB device number 4 using ehci-platform
[   24.710000] bitmainbl 1-1.1:1.0: USB Bitmain bootloader device now attached to USB Bitmain bootloader-0
[   24.720000] PIC microchip bootloader usb OK
[   34.110000] no int in filled
[   35.570000] usb 1-1.1: USB disconnect, device number 4
[   35.580000] bitmainbl 1-1.1:1.0: USB Bitmain asic #0 now disconnected
[   36.000000] usb 1-1.1: new full-speed USB device number 5 using ehci-platform
[   36.140000] bitmain 1-1.1:1.0: USB Bitmain asic device now attached to USB Bitmain asic-0
[   36.150000] PIC microchip usb OK
[  135.440000] bitmain 1-1.1:1.0: USB Bitmain asic #0 now disconnected

Code:

Thu Jan  1 08:00:11 1970 kern.info kernel: [    0.080000] pid_max: default: 32768 minimum: 301
Thu Jan  1 08:00:11 1970 kern.info kernel: [    0.080000] Mount-cache hash table entries: 512
Thu Jan  1 08:00:11 1970 kern.info kernel: [    0.090000] NET: Registered protocol family 16
Thu Jan  1 08:00:11 1970 kern.info kernel: [    0.100000] MIPS: machine is TP-LINK TL-WR741ND v4
Thu Jan  1 08:00:11 1970 kern.info kernel: [    0.550000] bio: create slab <bio-0> at 0
Thu Jan  1 08:00:11 1970 kern.info kernel: [    0.560000] Switching to clocksource MIPS
Thu Jan  1 08:00:11 1970 kern.info kernel: [    0.560000] NET: Registered protocol family 2
Thu Jan  1 08:00:11 1970 kern.info kernel: [    0.570000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
Thu Jan  1 08:00:11 1970 kern.info kernel: [    0.570000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
Thu Jan  1 08:00:11 1970 kern.info kernel: [    0.570000] TCP: Hash tables configured (established 512 bind 512)
Thu Jan  1 08:00:11 1970 kern.info kernel: [    0.580000] TCP: reno registered
Thu Jan  1 08:00:11 1970 kern.info kernel: [    0.580000] UDP hash table entries: 256 (order: 0, 4096 bytes)
Thu Jan  1 08:00:11 1970 kern.info kernel: [    0.590000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
Thu Jan  1 08:00:11 1970 kern.info kernel: [    0.600000] NET: Registered protocol family 1
Thu Jan  1 08:00:11 1970 kern.debug kernel: [    0.600000] PCI: CLS 0 bytes, default 32
Thu Jan  1 08:00:11 1970 kern.info kernel: [    0.620000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
Thu Jan  1 08:00:11 1970 kern.info kernel: [    0.620000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
Thu Jan  1 08:00:11 1970 kern.info kernel: [    0.630000] msgmni has been set to 119
Thu Jan  1 08:00:11 1970 kern.info kernel: [    0.630000] io scheduler noop registered
Thu Jan  1 08:00:11 1970 kern.info kernel: [    0.640000] io scheduler deadline registered (default)
Thu Jan  1 08:00:11 1970 kern.info kernel: [    0.640000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
Thu Jan  1 08:00:11 1970 kern.info kernel: [    0.650000] ar933x-uart: ttyATH0 at MMIO 0x18020000 (irq = 11) is a AR933X UART
Thu Jan  1 08:00:11 1970 kern.info kernel: [    0.660000] console [ttyATH0] enabled, bootconsole disabled
Thu Jan  1 08:00:11 1970 kern.info kernel: [    0.670000] ath79-spi ath79-spi: master is unqueued, this is deprecated
Thu Jan  1 08:00:11 1970 kern.warn kernel: [    0.680000] m25p80 spi0.0: found s25fl064k, expected m25p80
Thu Jan  1 08:00:11 1970 kern.info kernel: [    0.680000] m25p80 spi0.0: s25fl064k (8192 Kbytes)
Thu Jan  1 08:00:11 1970 kern.notice kernel: [    0.690000] 5 tp-link partitions found on MTD device spi0.0
Thu Jan  1 08:00:11 1970 kern.notice kernel: [    0.690000] Creating 5 MTD partitions on "spi0.0":
Thu Jan  1 08:00:11 1970 kern.notice kernel: [    0.700000] 0x000000000000-0x000000020000 : "u-boot"
Thu Jan  1 08:00:11 1970 kern.notice kernel: [    0.700000] 0x000000020000-0x000000117d84 : "kernel"
Thu Jan  1 08:00:11 1970 kern.warn kernel: [    0.710000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
Thu Jan  1 08:00:11 1970 kern.notice kernel: [    0.720000] 0x000000117d84-0x0000007f0000 : "rootfs"
Thu Jan  1 08:00:11 1970 kern.warn kernel: [    0.720000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
Thu Jan  1 08:00:11 1970 kern.notice kernel: [    0.740000] mtd: partition "rootfs" set to be root filesystem
Thu Jan  1 08:00:11 1970 kern.info kernel: [    0.740000] mtd: partition "rootfs_data" created automatically, ofs=0x370000, len=0x480000
Thu Jan  1 08:00:11 1970 kern.notice kernel: [    0.750000] 0x000000370000-0x0000007f0000 : "rootfs_data"
Thu Jan  1 08:00:11 1970 kern.notice kernel: [    0.760000] 0x000000020000-0x0000007f0000 : "firmware"
Thu Jan  1 08:00:11 1970 kern.notice kernel: [    0.760000] 0x0000007f0000-0x000000800000 : "art"
Thu Jan  1 08:00:11 1970 kern.info kernel: [    0.780000] libphy: ag71xx_mdio: probed
Thu Jan  1 08:00:11 1970 kern.info kernel: [    0.790000] eth0: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
Thu Jan  1 08:00:11 1970 kern.info kernel: [    1.340000] eth0: Found an AR7240/AR9330 built-in switch
Thu Jan  1 08:00:11 1970 kern.info kernel: [    2.380000] eth1: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
Thu Jan  1 08:00:11 1970 kern.info kernel: [    2.930000] ag71xx ag71xx.0 eth1: connected to PHY at ag71xx-mdio.1:04 [uid=004dd041, driver=Generic PHY]
Thu Jan  1 08:00:11 1970 kern.info kernel: [    2.940000] TCP: cubic registered
Thu Jan  1 08:00:11 1970 kern.info kernel: [    2.940000] NET: Registered protocol family 17
Thu Jan  1 08:00:11 1970 kern.info kernel: [    2.950000] 8021q: 802.1Q VLAN Support v1.8
Thu Jan  1 08:00:11 1970 kern.info kernel: [    2.960000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Thu Jan  1 08:00:11 1970 kern.info kernel: [    2.970000] Freeing unused kernel memory: 232K (80316000 - 80350000)
Thu Jan  1 08:00:11 1970 kern.info kernel: [    5.800000] usbcore: registered new interface driver usbfs
Thu Jan  1 08:00:11 1970 kern.info kernel: [    5.800000] usbcore: registered new interface driver hub
Thu Jan  1 08:00:11 1970 kern.info kernel: [    5.810000] usbcore: registered new device driver usb
Thu Jan  1 08:00:11 1970 kern.info kernel: [    5.810000] usbcore: registered new interface driver bitmain
Thu Jan  1 08:00:11 1970 kern.warn kernel: [    5.820000] hash ok
Thu Jan  1 08:00:11 1970 kern.warn kernel: [    5.820000] hashtest OK
Thu Jan  1 08:00:11 1970 kern.err kernel: [    5.820000] bitmain-asic: success to register device
Thu Jan  1 08:00:11 1970 kern.info kernel: [    5.830000] usbcore: registered new interface driver bitmainbl
Thu Jan  1 08:00:11 1970 kern.info kernel: [    5.840000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Thu Jan  1 08:00:11 1970 kern.info kernel: [    5.850000] ehci-platform: EHCI generic platform driver
Thu Jan  1 08:00:11 1970 kern.info kernel: [    5.850000] ehci-platform ehci-platform: EHCI Host Controller
Thu Jan  1 08:00:11 1970 kern.info kernel: [    5.860000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
Thu Jan  1 08:00:11 1970 kern.info kernel: [    5.860000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
Thu Jan  1 08:00:11 1970 kern.info kernel: [    5.890000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
Thu Jan  1 08:00:11 1970 kern.info kernel: [    5.890000] hub 1-0:1.0: USB hub found
Thu Jan  1 08:00:11 1970 kern.info kernel: [    5.890000] hub 1-0:1.0: 1 port detected
Thu Jan  1 08:00:11 1970 kern.info kernel: [    6.230000] usb 1-1: new high-speed USB device number 2 using ehci-platform
Thu Jan  1 08:00:11 1970 kern.info kernel: [    6.380000] hub 1-1:1.0: USB hub found
Thu Jan  1 08:00:11 1970 kern.info kernel: [    6.380000] hub 1-1:1.0: 2 ports detected
Thu Jan  1 08:00:11 1970 kern.info kernel: [    6.670000] usb 1-1.1: new full-speed USB device number 3 using ehci-platform
Thu Jan  1 08:00:11 1970 kern.info kernel: [    6.800000] bitmain 1-1.1:1.0: USB Bitmain asic device now attached to USB Bitmain asic-0
Thu Jan  1 08:00:11 1970 kern.warn kernel: [    6.810000] PIC microchip usb OK
Thu Jan  1 08:00:11 1970 kern.notice kernel: [   10.560000] jffs2: notice: (328) jffs2_build_xattr_subsystem: complete building xattr subsystem, 25 of xdatum (0 unchecked, 24 orphan) and 40 of xref (0 dead, 24 orphan) found.
Mon Dec  2 11:58:00 2013 daemon.info sysinit: Mon Dec  2 03:58:00 UTC 2013
Mon Dec  2 11:58:00 2013 user.emerg syslog: kmodloader: loading kernel modules from /etc/modules.d/**
Mon Dec  2 11:58:00 2013 kern.info kernel: [   12.820000] hidraw: raw HID events driver (C) Jiri Kosina
Mon Dec  2 11:58:00 2013 kern.info kernel: [   12.830000] Loading modules backported from Linux version master-2013-06-27-0-gdcfa6d5
Mon Dec  2 11:58:00 2013 kern.info kernel: [   12.830000] Backport generated by backports.git backports-20130617-4-ge3220f5
Mon Dec  2 11:58:00 2013 kern.info kernel: [   12.850000] nf_conntrack version 0.5.0 (962 buckets, 3848 max)
Mon Dec  2 11:58:00 2013 kern.info kernel: [   12.870000] usbcore: registered new interface driver usbhid
Mon Dec  2 11:58:00 2013 kern.info kernel: [   12.880000] usbhid: USB HID core driver
Mon Dec  2 11:58:00 2013 kern.info kernel: [   12.890000] usbcore: registered new interface driver usbserial
Mon Dec  2 11:58:00 2013 kern.info kernel: [   12.890000] usbcore: registered new interface driver usbserial_generic
Mon Dec  2 11:58:00 2013 kern.info kernel: [   12.900000] usbserial: USB Serial support registered for generic
Mon Dec  2 11:58:00 2013 kern.info kernel: [   12.930000] xt_time: kernel timezone is -0000
Mon Dec  2 11:58:00 2013 kern.info kernel: [   12.960000] cfg80211: Calling CRDA to update world regulatory domain
Mon Dec  2 11:58:00 2013 kern.info kernel: [   12.960000] cfg80211: World regulatory domain updated:
Mon Dec  2 11:58:00 2013 kern.info kernel: [   12.970000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
Mon Dec  2 11:58:00 2013 kern.info kernel: [   12.970000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
Mon Dec  2 11:58:00 2013 kern.info kernel: [   12.980000] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
Mon Dec  2 11:58:00 2013 kern.info kernel: [   12.990000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
Mon Dec  2 11:58:00 2013 kern.info kernel: [   13.000000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
Mon Dec  2 11:58:00 2013 kern.info kernel: [   13.000000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
Mon Dec  2 11:58:00 2013 kern.info kernel: [   13.020000] ip_tables: (C) 2000-2006 Netfilter Core Team
Mon Dec  2 11:58:00 2013 kern.debug kernel: [   13.160000] ath: EEPROM regdomain: 0x0
Mon Dec  2 11:58:00 2013 kern.debug kernel: [   13.160000] ath: EEPROM indicates default country code should be used
Mon Dec  2 11:58:00 2013 kern.debug kernel: [   13.160000] ath: doing EEPROM country->regdmn map search
Mon Dec  2 11:58:00 2013 kern.debug kernel: [   13.160000] ath: country maps to regdmn code: 0x3a
Mon Dec  2 11:58:00 2013 kern.debug kernel: [   13.160000] ath: Country alpha2 being used: US
Mon Dec  2 11:58:00 2013 kern.debug kernel: [   13.160000] ath: Regpair used: 0x3a
Mon Dec  2 11:58:00 2013 kern.debug kernel: [   13.160000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
Mon Dec  2 11:58:00 2013 kern.info kernel: [   13.180000] cfg80211: Calling CRDA for country: US
Mon Dec  2 11:58:00 2013 kern.info kernel: [   13.180000] cfg80211: Regulatory domain changed to country: US
Mon Dec  2 11:58:00 2013 kern.info kernel: [   13.190000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
Mon Dec  2 11:58:00 2013 kern.info kernel: [   13.200000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
Mon Dec  2 11:58:00 2013 kern.info kernel: [   13.210000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
Mon Dec  2 11:58:00 2013 kern.info kernel: [   13.210000] cfg80211:   (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
Mon Dec  2 11:58:00 2013 kern.info kernel: [   13.220000] cfg80211:   (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
Mon Dec  2 11:58:00 2013 kern.info kernel: [   13.230000] cfg80211:   (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
Mon Dec  2 11:58:00 2013 kern.info kernel: [   13.240000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
Mon Dec  2 11:58:00 2013 kern.info kernel: [   13.250000] ieee80211 phy0: Atheros AR9330 Rev:1 mem=0xb8100000, irq=2
Mon Dec  2 11:58:00 2013 user.info syslog: ran 16 iterations
Mon Dec  2 11:58:00 2013 daemon.info sysinit: kmod: ran 16 iterations
Mon Dec  2 11:58:04 2013 cron.info crond[566]: crond: crond (busybox 1.19.4) started, log level 5
Mon Dec  2 11:58:05 2013 authpriv.info dropbear[586]: Not backgrounding
Mon Dec  2 11:58:05 2013 kern.info kernel: [   18.030000] device eth0 entered promiscuous mode
Mon Dec  2 11:58:05 2013 daemon.notice netifd: Interface 'loopback' is now up
Mon Dec  2 11:58:05 2013 daemon.notice netifd: Interface 'wan' is now up
Mon Dec  2 11:58:05 2013 daemon.notice netifd: lan (632): udhcpc (v1.19.4) started
Mon Dec  2 11:58:06 2013 daemon.notice netifd: lan (632): Sending discover...
Mon Dec  2 11:58:06 2013 user.notice firewall: Reloading firewall due to ifup of wan (eth1)
Mon Dec  2 11:58:07 2013 kern.info kernel: [   20.300000] eth1: link up (100Mbps/Full duplex)
Mon Dec  2 11:58:07 2013 user.notice dnsmasq: DNS rebinding protection is active, will discard upstream RFC1918 responses!
Mon Dec  2 11:58:07 2013 user.notice dnsmasq: Allowing 127.0.0.0/8 responses
Mon Dec  2 11:58:09 2013 daemon.notice netifd: lan (632): Sending discover...
Mon Dec  2 11:58:11 2013 daemon.info sysinit: /etc/config/miner_pic.hex
Mon Dec  2 11:58:11 2013 daemon.info dnsmasq[785]: started, version 2.66 cachesize 150
Mon Dec  2 11:58:11 2013 daemon.info dnsmasq[785]: compile time options: IPv6 GNU-getopt no-DBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-auth
Mon Dec  2 11:58:11 2013 daemon.info dnsmasq-dhcp[785]: DHCP, IP range 192.168.1.100 -- 192.168.1.249, lease time 12h
Mon Dec  2 11:58:11 2013 daemon.info dnsmasq[785]: using local addresses only for domain lan
Mon Dec  2 11:58:11 2013 daemon.info dnsmasq[785]: reading /tmp/resolv.conf.auto
Mon Dec  2 11:58:11 2013 daemon.info dnsmasq[785]: using nameserver 192.168.1.1#53
Mon Dec  2 11:58:11 2013 daemon.info dnsmasq[785]: using local addresses only for domain lan
Mon Dec  2 11:58:11 2013 daemon.info dnsmasq[785]: read /etc/hosts - 1 addresses
Mon Dec  2 11:58:11 2013 daemon.info dnsmasq-dhcp[785]: read /etc/ethers - 0 addresses
Mon Dec  2 11:58:11 2013 kern.info kernel: [   24.300000] usb 1-1.1: USB disconnect, device number 3
Mon Dec  2 11:58:11 2013 kern.info kernel: [   24.310000] bitmain 1-1.1:1.0: USB Bitmain asic #0 now disconnected
Mon Dec  2 11:58:11 2013 kern.info kernel: [   24.570000] usb 1-1.1: new full-speed USB device number 4 using ehci-platform
Mon Dec  2 11:58:12 2013 kern.info kernel: [   24.710000] bitmainbl 1-1.1:1.0: USB Bitmain bootloader device now attached to USB Bitmain bootloader-0
Mon Dec  2 11:58:12 2013 kern.warn kernel: [   24.720000] PIC microchip bootloader usb OK
Mon Dec  2 11:58:12 2013 daemon.notice netifd: lan (632): Sending discover...
Mon Dec  2 11:58:21 2013 kern.warn kernel: [   34.110000] no int in filled
Mon Dec  2 11:58:21 2013 daemon.info sysinit: pic update
Mon Dec  2 11:58:21 2013 daemon.info sysinit: open /dev/bitmain0 to restart pic
Mon Dec  2 11:58:21 2013 daemon.info sysinit: open /dev/bitmainbl0 ok fd = 0x4
Mon Dec  2 11:58:21 2013 daemon.info sysinit: read data
Mon Dec  2 11:58:21 2013 daemon.info sysinit: [0]{0x1}, [1]{0x10}, [2]{0x1}, [3]{0x10}, [4]{0x1}, [5]{0}, [6]{0x10}, [7]{0x1}, [8]{0x10}, [9]{0x4}, [10]{0x4}, 
Mon Dec  2 11:58:21 2013 daemon.info sysinit: Version 1.0
Mon Dec  2 11:58:21 2013 daemon.info sysinit: open pic update file fail 
Mon Dec  2 11:58:21 2013 daemon.info sysinit: Control bootloader to app
Mon Dec  2 11:58:21 2013 daemon.info sysinit: setting up led WAN
Mon Dec  2 11:58:21 2013 daemon.info sysinit: setting up led WANL
Mon Dec  2 11:58:21 2013 daemon.info sysinit: setting up led LAN1
Mon Dec  2 11:58:21 2013 daemon.info sysinit: setting up led LAN2
Mon Dec  2 11:58:21 2013 daemon.info sysinit: setting up led LAN3
Mon Dec  2 11:58:21 2013 daemon.info sysinit: setting up led LAN4
Mon Dec  2 11:58:21 2013 daemon.info sysinit: setting up led WLAN
Mon Dec  2 11:58:22 2013 kern.info kernel: [   35.570000] usb 1-1.1: USB disconnect, device number 4
Mon Dec  2 11:58:23 2013 kern.info kernel: [   35.580000] bitmainbl 1-1.1:1.0: USB Bitmain asic #0 now disconnected
Mon Dec  2 11:58:23 2013 kern.info kernel: [   36.000000] usb 1-1.1: new full-speed USB device number 5 using ehci-platform
Mon Dec  2 11:58:23 2013 kern.info kernel: [   36.140000] bitmain 1-1.1:1.0: USB Bitmain asic device now attached to USB Bitmain asic-0
Mon Dec  2 11:58:23 2013 kern.warn kernel: [   36.150000] PIC microchip usb OK
Mon Dec  2 11:58:56 2013 daemon.info sysinit: ntpd: bad address '3.openwrt.pool.ntp.org'
Mon Dec  2 11:58:56 2013 daemon.info sysinit: ntpd: could not resolve peer 3.openwrt.pool.ntp.org, skipping
Mon Dec  2 11:59:26 2013 daemon.info sysinit: ntpd: bad address '2.openwrt.pool.ntp.org'
Mon Dec  2 11:59:26 2013 daemon.info sysinit: ntpd: could not resolve peer 2.openwrt.pool.ntp.org, skipping
Mon Dec  2 11:59:56 2013 daemon.info sysinit: ntpd: bad address '1.openwrt.pool.ntp.org'
Mon Dec  2 11:59:56 2013 daemon.info sysinit: ntpd: could not resolve peer 1.openwrt.pool.ntp.org, skipping
Mon Dec  2 12:00:01 2013 cron.info crond[566]: crond: USER root pid 854 cmd /usr/bin/cgminer-monitor
Mon Dec  2 12:00:02 2013 kern.info kernel: [  135.440000] bitmain 1-1.1:1.0: USB Bitmain asic #0 now disconnected
Mon Dec  2 12:00:26 2013 daemon.info sysinit: ntpd: bad address '0.openwrt.pool.ntp.org'
Mon Dec  2 12:00:26 2013 daemon.info sysinit: ntpd: could not resolve peer 0.openwrt.pool.ntp.org, skipping
Mon Dec  2 12:00:32 2013 daemon.info sysinit: Alarm clock
Mon Dec  2 12:00:32 2013 daemon.info sysinit: --bitmain-options 115200:32:8::: -o stratum.mining.eligius.st:3334 -O 1DiBRqnfKV7eSekycQ7VHVoZSzxG1nGSRW:123 --api-listen --api-network
Mon Dec  2 12:00:32 2013 daemon.info sysinit: - init complete -
Mon Dec  2 12:03:01 2013 cron.info crond[566]: crond: USER root pid 910 cmd /usr/bin/cgminer-monitor
Mon Dec  2 12:06:01 2013 cron.info crond[566]: crond: USER root pid 2374 cmd /usr/bin/cgminer-monitor
Mon Dec  2 12:07:48 2013 authpriv.info dropbear[2399]: Child connection from 192.168.1.69:57963
Mon Dec  2 12:07:57 2013 authpriv.notice dropbear[2399]: Password auth succeeded for 'root' from 192.168.1.69:57963
Mon Dec  2 12:09:01 2013 cron.info crond[566]: crond: USER root pid 2410 cmd /usr/bin/cgminer-monitor
Mon Dec  2 12:12:01 2013 cron.info crond[566]: crond: USER root pid 2439 cmd /usr/bin/cgminer-monitor
Mon Dec  2 12:15:01 2013 cron.info crond[566]: crond: USER root pid 2461 cmd /usr/bin/cgminer-monitor
Mon Dec  2 12:18:01 2013 cron.info crond[566]: crond: USER root pid 2483 cmd /usr/bin/cgminer-monitor
Mon Dec  2 12:21:01 2013 cron.info crond[566]: crond: USER root pid 2505 cmd /usr/bin/cgminer-monitor
Mon Dec  2 12:24:01 2013 cron.info crond[566]: crond: USER root pid 2532 cmd /usr/bin/cgminer-monitor
Mon Dec  2 12:27:01 2013 cron.info crond[566]: crond: USER root pid 2554 cmd /usr/bin/cgminer-monitor

here is the processes on going

Code:

1
root
/sbin/procd
0%
2%



2
root
[kthreadd]
0%
0%



3
root
[ksoftirqd/0]
0%
0%



5
root
[kworker/0:0H]
0%
0%



6
root
[kworker/u2:0]
0%
0%



7
root
[khelper]
0%
0%



60
root
[writeback]
0%
0%



62
root
[bioset]
0%
0%



64
root
[kblockd]
0%
0%



89
root
[kworker/0:1]
0%
0%



94
root
[kswapd0]
0%
0%



139
root
[fsnotify_mark]
0%
0%



152
root
[ath79-spi]
0%
0%



230
root
[deferwq]
0%
0%



231
root
[kworker/0:2]
0%
0%



241
root
[khubd]
0%
0%



268
root
[kworker/u2:2]
0%
0%



329
root
[jffs2_gcd_mtd3]
0%
0%



383
root
ubusd
0%
1%



384
root
/sbin/askfirst ttyATH0 /bin/ash --login
0%
1%



458
root
[cfg80211]
0%
0%



531
root
/sbin/netifd
0%
2%



566
root
/usr/sbin/crond -f -c /etc/crontabs -l 5
0%
2%



586
root
/usr/sbin/dropbear -F -P /var/run/dropbear.1.pid -p 22
0%
2%



632
root
udhcpc -p /var/run/udhcpc-br-lan.pid -s /lib/netifd/dhcp.script -f -t 0 -i br-lan -C
0%
2%



667
root
/usr/sbin/uhttpd -f -h /www -r antMiner -x /cgi-bin -t 60 -T 30 -k 20 -A 1 -n 3 -N 100 -R -p 0.0.0.0 80
0%
2%



785
nobody
/usr/sbin/dnsmasq -C /var/etc/dnsmasq.conf -k
0%
2%



830
root
/usr/sbin/ntpd -n -p 0.openwrt.pool.ntp.org -p 1.openwrt.pool.ntp.org -p 2.openwrt.pool.ntp.org -p 3.openwrt.pool.ntp.org
0%
2%



2399
root
/usr/sbin/dropbear -F -P /var/run/dropbear.1.pid -p 22
0%
2%



2400
root
-ash
0%
2%



2582
root
{luci} /usr/bin/lua /www/cgi-bin/luci
0%
5%



2583
root
sh -c /bin/busybox top -bn1
0%
2%



2584
root
/bin/busybox top -bn1
9%
2%

[kabopar]

Why don't you simply use the web gui (follow one of the guides either https://bitcointalk.org/index.php?topic=344970.0 or https://bitcointalk.org/index.php?topic=355387.0)

You can't find any devices because the built-in TP-link WRT thing is already using them, and sending your coins to Bitmain test pools...

That would get you going.  You can explore deeper later...

Cheers

[xref]

alright, am using the GUI, the miner status shows me that its not mining, and i dont see cgminer running under processes.
this why i used ssh to run the cgminer, because i want to see what kind of error its encountering, its says no devices, no servers were found, wrong URL. dont know what the fuck is wrong with this.

[alfabitcoin]

alright, am using the GUI, the miner status shows me that its not mining, and i dont see cgminer running under processes.
this why i used ssh to run the cgminer, because i want to see what kind of error its encountering, its says no devices, no servers were found, wrong URL. dont know what the fuck is wrong with this.

Check ntp, try to set custom dns to 8.8.8.8.
Read sushi thread.
Here is ntp servers

198.58.100.237
209.118.204.201
199.195.193.200
189.211.62.210

[kabopar]

alright, am using the GUI, the miner status shows me that its not mining, and i dont see cgminer running under processes.
this why i used ssh to run the cgminer, because i want to see what kind of error its encountering, its says no devices, no servers were found, wrong URL. dont know what the fuck is wrong with this.

Did you enter your pool parameters correctly?  (I had a typo when entering my pool info, and it wouldn't mine, was in a mild state of panic as it is my first S1... double check that you entered it correctly)
You enter/modify your pool settings in Status, miner configuration (enter, then click 'save and apply', wait until the 'turning wheel' stops, then go to the miner status tab, and wait for the mining to start, it takes a while (usually the pool sees it before the WRT gui does).
On the System, software tab you should see that cgminer is installed (ver 3.12.0-1 on my one)
also on the System, startup tab you should see cgminer (at the bottom of my list).
On Status, processes you should see a line with cgminer, some options and your pool settings.
Do you see cgminer in all of these?
Perhaps you should try a system reset, or shut it down, remove power for a while, then start it from scratch.

Good luck

[alfabitcoin]

From syslog is clear that ntp server problems. Your isp may have dns resolve restrictions, so try different ntp servers as mentioned in above problems ( read sushi setup thread under troubleshoot)

[xref]

Done
did add the ntp servers, and did set custom dns to 8.8.8.8
actualy i did read his thread twice, not sure what exactly is wrong, the green lights that suppose to light while mining aren't lighting up at all

[kabopar]

From syslog is clear that ntp server problems. Your isp may have dns resolve restrictions, so try different ntp servers as mentioned in above problems ( read sushi setup thread under troubleshoot)

You are probably correct
"Mon Dec  2 12:00:26 2013 daemon.info sysinit: ntpd: bad address '0.openwrt.pool.ntp.org'
Mon Dec  2 12:00:26 2013 daemon.info sysinit: ntpd: could not resolve peer 0.openwrt.pool.ntp.org, skipping"

[kabopar]

Done
did add the ntp servers, and did set custom dns to 8.8.8.8
actualy i did read his thread twice, not sure what exactly is wrong, the green lights that suppose to light while mining aren't lighting up at all

It's not just the lights, the fan increases speed, it is a big 'change'.  Is your PSU capable to support this?  I'm using a 650W PSU, with the PCI-e 6 pin connectors used from separate rails to drive each of the blades.
In my case only the WAN connection is used.  Are you using the IP address from the sticker on your unit?  (noticed that yours differs from the 'nominal' 192.168.1.99).  Is your router configured to cope with your fixed IP address?  (probably is, as you can see the Gui and can SSH).  Are you connected through the wired ethernet interface or wifi?  Are there any restrictions on your internet connection?

Good luck

[xref]

no there any kind of restriction, and using ethernet

here is an updated system log after i added the new adresses
still the miner refuse to work

Code:

Thu Jan  1 08:00:11 1970 kern.notice kernel: [    0.760000] 0x000000020000-0x0000007f0000 : "firmware"
Thu Jan  1 08:00:11 1970 kern.notice kernel: [    0.760000] 0x0000007f0000-0x000000800000 : "art"
Thu Jan  1 08:00:11 1970 kern.info kernel: [    0.780000] libphy: ag71xx_mdio: probed
Thu Jan  1 08:00:11 1970 kern.info kernel: [    0.790000] eth0: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
Thu Jan  1 08:00:11 1970 kern.info kernel: [    1.340000] eth0: Found an AR7240/AR9330 built-in switch
Thu Jan  1 08:00:11 1970 kern.info kernel: [    2.380000] eth1: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
Thu Jan  1 08:00:11 1970 kern.info kernel: [    2.930000] ag71xx ag71xx.0 eth1: connected to PHY at ag71xx-mdio.1:04 [uid=004dd041, driver=Generic PHY]
Thu Jan  1 08:00:11 1970 kern.info kernel: [    2.940000] TCP: cubic registered
Thu Jan  1 08:00:11 1970 kern.info kernel: [    2.940000] NET: Registered protocol family 17
Thu Jan  1 08:00:11 1970 kern.info kernel: [    2.950000] 8021q: 802.1Q VLAN Support v1.8
Thu Jan  1 08:00:11 1970 kern.info kernel: [    2.960000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Thu Jan  1 08:00:11 1970 kern.info kernel: [    2.970000] Freeing unused kernel memory: 232K (80316000 - 80350000)
Thu Jan  1 08:00:11 1970 kern.info kernel: [    5.800000] usbcore: registered new interface driver usbfs
Thu Jan  1 08:00:11 1970 kern.info kernel: [    5.800000] usbcore: registered new interface driver hub
Thu Jan  1 08:00:11 1970 kern.info kernel: [    5.810000] usbcore: registered new device driver usb
Thu Jan  1 08:00:11 1970 kern.info kernel: [    5.810000] usbcore: registered new interface driver bitmain
Thu Jan  1 08:00:11 1970 kern.warn kernel: [    5.820000] hash ok
Thu Jan  1 08:00:11 1970 kern.warn kernel: [    5.820000] hashtest OK
Thu Jan  1 08:00:11 1970 kern.err kernel: [    5.820000] bitmain-asic: success to register device
Thu Jan  1 08:00:11 1970 kern.info kernel: [    5.830000] usbcore: registered new interface driver bitmainbl
Thu Jan  1 08:00:11 1970 kern.info kernel: [    5.840000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Thu Jan  1 08:00:11 1970 kern.info kernel: [    5.850000] ehci-platform: EHCI generic platform driver
Thu Jan  1 08:00:11 1970 kern.info kernel: [    5.850000] ehci-platform ehci-platform: EHCI Host Controller
Thu Jan  1 08:00:11 1970 kern.info kernel: [    5.860000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
Thu Jan  1 08:00:11 1970 kern.info kernel: [    5.860000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
Thu Jan  1 08:00:11 1970 kern.info kernel: [    5.890000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
Thu Jan  1 08:00:11 1970 kern.info kernel: [    5.890000] hub 1-0:1.0: USB hub found
Thu Jan  1 08:00:11 1970 kern.info kernel: [    5.890000] hub 1-0:1.0: 1 port detected
Thu Jan  1 08:00:11 1970 kern.info kernel: [    6.230000] usb 1-1: new high-speed USB device number 2 using ehci-platform
Thu Jan  1 08:00:11 1970 kern.info kernel: [    6.380000] hub 1-1:1.0: USB hub found
Thu Jan  1 08:00:11 1970 kern.info kernel: [    6.380000] hub 1-1:1.0: 2 ports detected
Thu Jan  1 08:00:11 1970 kern.info kernel: [    6.670000] usb 1-1.1: new full-speed USB device number 3 using ehci-platform
Thu Jan  1 08:00:11 1970 kern.info kernel: [    6.800000] bitmain 1-1.1:1.0: USB Bitmain asic device now attached to USB Bitmain asic-0
Thu Jan  1 08:00:11 1970 kern.warn kernel: [    6.810000] PIC microchip usb OK
Thu Jan  1 08:00:11 1970 kern.notice kernel: [   10.560000] jffs2: notice: (328) jffs2_build_xattr_subsystem: complete building xattr subsystem, 25 of xdatum (0 unchecked, 24 orphan) and 44 of xref (0 dead, 28 orphan) found.
Fri Mar 28 22:47:00 2014 daemon.info sysinit: Fri Mar 28 14:47:00 UTC 2014
Fri Mar 28 22:47:00 2014 user.emerg syslog: kmodloader: loading kernel modules from /etc/modules.d/**
Fri Mar 28 22:47:00 2014 kern.info kernel: [   12.820000] hidraw: raw HID events driver (C) Jiri Kosina
Fri Mar 28 22:47:00 2014 kern.info kernel: [   12.830000] Loading modules backported from Linux version master-2013-06-27-0-gdcfa6d5
Fri Mar 28 22:47:00 2014 kern.info kernel: [   12.830000] Backport generated by backports.git backports-20130617-4-ge3220f5
Fri Mar 28 22:47:00 2014 kern.info kernel: [   12.850000] nf_conntrack version 0.5.0 (962 buckets, 3848 max)
Fri Mar 28 22:47:00 2014 kern.info kernel: [   12.870000] usbcore: registered new interface driver usbhid
Fri Mar 28 22:47:00 2014 kern.info kernel: [   12.880000] usbhid: USB HID core driver
Fri Mar 28 22:47:00 2014 kern.info kernel: [   12.890000] usbcore: registered new interface driver usbserial
Fri Mar 28 22:47:00 2014 kern.info kernel: [   12.890000] usbcore: registered new interface driver usbserial_generic
Fri Mar 28 22:47:00 2014 kern.info kernel: [   12.900000] usbserial: USB Serial support registered for generic
Fri Mar 28 22:47:00 2014 kern.info kernel: [   12.930000] xt_time: kernel timezone is -0000
Fri Mar 28 22:47:00 2014 kern.info kernel: [   12.960000] cfg80211: Calling CRDA to update world regulatory domain
Fri Mar 28 22:47:00 2014 kern.info kernel: [   12.960000] cfg80211: World regulatory domain updated:
Fri Mar 28 22:47:00 2014 kern.info kernel: [   12.970000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
Fri Mar 28 22:47:00 2014 kern.info kernel: [   12.970000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
Fri Mar 28 22:47:00 2014 kern.info kernel: [   12.980000] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
Fri Mar 28 22:47:00 2014 kern.info kernel: [   12.990000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
Fri Mar 28 22:47:00 2014 kern.info kernel: [   13.000000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
Fri Mar 28 22:47:00 2014 kern.info kernel: [   13.000000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
Fri Mar 28 22:47:00 2014 kern.info kernel: [   13.020000] ip_tables: (C) 2000-2006 Netfilter Core Team
Fri Mar 28 22:47:00 2014 kern.debug kernel: [   13.170000] ath: EEPROM regdomain: 0x0
Fri Mar 28 22:47:00 2014 kern.debug kernel: [   13.170000] ath: EEPROM indicates default country code should be used
Fri Mar 28 22:47:00 2014 kern.debug kernel: [   13.170000] ath: doing EEPROM country->regdmn map search
Fri Mar 28 22:47:00 2014 kern.debug kernel: [   13.170000] ath: country maps to regdmn code: 0x3a
Fri Mar 28 22:47:00 2014 kern.debug kernel: [   13.170000] ath: Country alpha2 being used: US
Fri Mar 28 22:47:00 2014 kern.debug kernel: [   13.170000] ath: Regpair used: 0x3a
Fri Mar 28 22:47:00 2014 kern.debug kernel: [   13.170000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
Fri Mar 28 22:47:00 2014 kern.info kernel: [   13.180000] cfg80211: Calling CRDA for country: US
Fri Mar 28 22:47:00 2014 kern.info kernel: [   13.180000] cfg80211: Regulatory domain changed to country: US
Fri Mar 28 22:47:00 2014 kern.info kernel: [   13.190000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
Fri Mar 28 22:47:00 2014 kern.info kernel: [   13.200000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
Fri Mar 28 22:47:00 2014 kern.info kernel: [   13.200000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
Fri Mar 28 22:47:00 2014 kern.info kernel: [   13.210000] cfg80211:   (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
Fri Mar 28 22:47:00 2014 kern.info kernel: [   13.220000] cfg80211:   (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
Fri Mar 28 22:47:00 2014 kern.info kernel: [   13.230000] cfg80211:   (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
Fri Mar 28 22:47:00 2014 kern.info kernel: [   13.240000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
Fri Mar 28 22:47:00 2014 kern.info kernel: [   13.240000] ieee80211 phy0: Atheros AR9330 Rev:1 mem=0xb8100000, irq=2
Fri Mar 28 22:47:00 2014 user.info syslog: ran 16 iterations
Fri Mar 28 22:47:00 2014 daemon.info sysinit: kmod: ran 16 iterations
Fri Mar 28 22:47:04 2014 cron.info crond[576]: crond: crond (busybox 1.19.4) started, log level 8
Fri Mar 28 22:47:05 2014 authpriv.info dropbear[587]: Not backgrounding
Fri Mar 28 22:47:05 2014 daemon.notice netifd: Interface 'loopback' is now up
Fri Mar 28 22:47:05 2014 kern.info kernel: [   17.980000] device eth0 entered promiscuous mode
Fri Mar 28 22:47:05 2014 daemon.notice netifd: Interface 'wan' is now up
Fri Mar 28 22:47:05 2014 daemon.notice netifd: lan (632): udhcpc (v1.19.4) started
Fri Mar 28 22:47:06 2014 daemon.notice netifd: lan (632): Sending discover...
Fri Mar 28 22:47:06 2014 user.notice firewall: Reloading firewall due to ifup of wan (eth1)
Fri Mar 28 22:47:07 2014 kern.info kernel: [   20.120000] eth1: link up (100Mbps/Full duplex)
Fri Mar 28 22:47:07 2014 user.notice dnsmasq: DNS rebinding protection is active, will discard upstream RFC1918 responses!
Fri Mar 28 22:47:07 2014 user.notice dnsmasq: Allowing 127.0.0.0/8 responses
Fri Mar 28 22:47:08 2014 daemon.info dnsmasq[694]: started, version 2.66 cachesize 150
Fri Mar 28 22:47:08 2014 daemon.info dnsmasq[694]: compile time options: IPv6 GNU-getopt no-DBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-auth
Fri Mar 28 22:47:08 2014 daemon.info dnsmasq[694]: using local addresses only for domain lan
Fri Mar 28 22:47:08 2014 daemon.info dnsmasq[694]: reading /tmp/resolv.conf.auto
Fri Mar 28 22:47:08 2014 daemon.info dnsmasq[694]: using nameserver 8.8.8.8#53
Fri Mar 28 22:47:08 2014 daemon.info dnsmasq[694]: using local addresses only for domain lan
Fri Mar 28 22:47:08 2014 daemon.info dnsmasq[694]: read /etc/hosts - 1 addresses
Fri Mar 28 22:47:08 2014 daemon.info sysinit: /etc/config/miner_pic.hex
Fri Mar 28 22:47:08 2014 kern.info kernel: [   20.980000] usb 1-1.1: USB disconnect, device number 3
Fri Mar 28 22:47:08 2014 kern.info kernel: [   20.980000] bitmain 1-1.1:1.0: USB Bitmain asic #0 now disconnected
Fri Mar 28 22:47:08 2014 kern.info kernel: [   21.240000] usb 1-1.1: new full-speed USB device number 4 using ehci-platform
Fri Mar 28 22:47:08 2014 kern.info kernel: [   21.380000] bitmainbl 1-1.1:1.0: USB Bitmain bootloader device now attached to USB Bitmain bootloader-0
Fri Mar 28 22:47:08 2014 kern.warn kernel: [   21.390000] PIC microchip bootloader usb OK
Fri Mar 28 22:47:09 2014 daemon.notice netifd: lan (632): Sending discover...
Fri Mar 28 22:47:12 2014 daemon.notice netifd: lan (632): Sending discover...
Fri Mar 28 22:47:18 2014 kern.warn kernel: [   30.860000] no int in filled
Fri Mar 28 22:47:18 2014 daemon.info sysinit: pic update
Fri Mar 28 22:47:18 2014 daemon.info sysinit: open /dev/bitmain0 to restart pic
Fri Mar 28 22:47:18 2014 daemon.info sysinit: open /dev/bitmainbl0 ok fd = 0x4
Fri Mar 28 22:47:18 2014 daemon.info sysinit: read data
Fri Mar 28 22:47:18 2014 daemon.info sysinit: [0]{0x1}, [1]{0x10}, [2]{0x1}, [3]{0x10}, [4]{0x1}, [5]{0}, [6]{0x10}, [7]{0x1}, [8]{0x10}, [9]{0x4}, [10]{0x4}, 
Fri Mar 28 22:47:18 2014 daemon.info sysinit: Version 1.0
Fri Mar 28 22:47:18 2014 daemon.info sysinit: open pic update file fail 
Fri Mar 28 22:47:18 2014 daemon.info sysinit: Control bootloader to app
Fri Mar 28 22:47:18 2014 daemon.info sysinit: setting up led WAN
Fri Mar 28 22:47:18 2014 daemon.info sysinit: setting up led WANL
Fri Mar 28 22:47:18 2014 daemon.info sysinit: setting up led LAN1
Fri Mar 28 22:47:18 2014 daemon.info sysinit: setting up led LAN2
Fri Mar 28 22:47:18 2014 daemon.info sysinit: setting up led LAN3
Fri Mar 28 22:47:18 2014 daemon.info sysinit: setting up led LAN4
Fri Mar 28 22:47:18 2014 daemon.info sysinit: setting up led WLAN
Fri Mar 28 22:47:19 2014 kern.info kernel: [   32.540000] usb 1-1.1: USB disconnect, device number 4
Fri Mar 28 22:47:19 2014 kern.info kernel: [   32.550000] bitmainbl 1-1.1:1.0: USB Bitmain asic #0 now disconnected
Fri Mar 28 22:47:20 2014 kern.info kernel: [   32.810000] usb 1-1.1: new full-speed USB device number 5 using ehci-platform
Fri Mar 28 22:47:20 2014 kern.info kernel: [   32.950000] bitmain 1-1.1:1.0: USB Bitmain asic device now attached to USB Bitmain asic-0
Fri Mar 28 22:47:20 2014 kern.warn kernel: [   32.960000] PIC microchip usb OK
Fri Mar 28 22:47:23 2014 daemon.info sysinit: ntpd: resolved peer 3.openwrt.pool.ntp.org to 212.26.18.43
Fri Mar 28 22:47:23 2014 daemon.info sysinit: ntpd: sent query to 212.26.18.43
Fri Mar 28 22:47:23 2014 daemon.info sysinit: ntpd: resolved peer 2.openwrt.pool.ntp.org to 212.26.18.43
Fri Mar 28 22:47:23 2014 daemon.info sysinit: ntpd: sent query to 212.26.18.43
Fri Mar 28 22:47:23 2014 daemon.info sysinit: ntpd: resolved peer 1.openwrt.pool.ntp.org to 108.61.56.35
Fri Mar 28 22:47:23 2014 daemon.info sysinit: ntpd: sent query to 108.61.56.35
Fri Mar 28 22:47:23 2014 daemon.info sysinit: ntpd: resolved peer 0.openwrt.pool.ntp.org to 212.26.18.41
Fri Mar 28 22:47:23 2014 daemon.info sysinit: ntpd: sent query to 212.26.18.41
Fri Mar 28 22:47:23 2014 daemon.info sysinit: ntpd: reply from 212.26.18.43: reach 0x01 offset 31.392257 delay 0.024711 status 0x24 strat 1 refid 0x47505300 rootdelay 0.000000
Fri Mar 28 22:47:23 2014 daemon.info sysinit: ntpd: reply from 212.26.18.43: reach 0x01 offset 31.392024 delay 0.024208 status 0x24 strat 1 refid 0x47505300 rootdelay 0.000000
Fri Mar 28 22:47:23 2014 daemon.info sysinit: ntpd: reply from 212.26.18.41: reach 0x01 offset 31.392283 delay 0.025412 status 0x24 strat 1 refid 0x47505300 rootdelay 0.000000
Fri Mar 28 22:47:23 2014 daemon.info sysinit: ntpd: reply from 108.61.56.35: reach 0x01 offset 31.386353 delay 0.189714 status 0x24 strat 2 refid 0x80040101 rootdelay 0.005249
Fri Mar 28 22:47:24 2014 daemon.info sysinit: ntpd: sent query to 212.26.18.43
Fri Mar 28 22:47:24 2014 daemon.info sysinit: ntpd: sent query to 108.61.56.35
Fri Mar 28 22:47:24 2014 daemon.info sysinit: ntpd: sent query to 212.26.18.41
Fri Mar 28 22:47:24 2014 daemon.info sysinit: ntpd: reply from 212.26.18.43: reach 0x03 offset 31.392005 delay 0.024258 status 0x24 strat 1 refid 0x47505300 rootdelay 0.000000
Fri Mar 28 22:47:24 2014 daemon.info sysinit: ntpd: reply from 212.26.18.41: reach 0x03 offset 31.394781 delay 0.029932 status 0x24 strat 1 refid 0x47505300 rootdelay 0.000000
Fri Mar 28 22:47:24 2014 daemon.info sysinit: ntpd: reply from 108.61.56.35: reach 0x03 offset 31.385279 delay 0.183138 status 0x24 strat 2 refid 0x80040101 rootdelay 0.005249
Fri Mar 28 22:47:25 2014 daemon.info sysinit: ntpd: sent query to 212.26.18.43
Fri Mar 28 22:47:25 2014 daemon.info sysinit: ntpd: sent query to 212.26.18.43
Fri Mar 28 22:47:25 2014 daemon.info sysinit: ntpd: sent query to 108.61.56.35
Fri Mar 28 22:47:25 2014 daemon.info sysinit: ntpd: reply from 212.26.18.43: reach 0x07 offset 31.390903 delay 0.023590 status 0x24 strat 1 refid 0x47505300 rootdelay 0.000000
Fri Mar 28 22:47:25 2014 daemon.info sysinit: ntpd: reply from 212.26.18.43: reach 0x03 offset 31.393261 delay 0.027357 status 0x24 strat 1 refid 0x47505300 rootdelay 0.000000
Fri Mar 28 22:47:25 2014 daemon.info sysinit: ntpd: reply from 108.61.56.35: reach 0x07 offset 31.392590 delay 0.199319 status 0x24 strat 2 refid 0x80040101 rootdelay 0.005249
Fri Mar 28 22:47:26 2014 daemon.info sysinit: ntpd: sent query to 212.26.18.41
Fri Mar 28 22:47:26 2014 daemon.info sysinit: ntpd: reply from 212.26.18.41: reach 0x07 offset 31.391484 delay 0.025133 status 0x24 strat 1 refid 0x47505300 rootdelay 0.000000
Fri Mar 28 22:47:27 2014 daemon.info sysinit: ntpd: sent query to 212.26.18.43
Fri Mar 28 22:47:27 2014 daemon.info sysinit: ntpd: sent query to 212.26.18.43
Fri Mar 28 22:47:27 2014 daemon.info sysinit: ntpd: sent query to 108.61.56.35
Fri Mar 28 22:47:27 2014 daemon.info sysinit: ntpd: reply from 212.26.18.43: reach 0x0f offset 31.392073 delay 0.024426 status 0x24 strat 1 refid 0x47505300 rootdelay 0.000000
Fri Mar 28 22:47:27 2014 daemon.info sysinit: ntpd: reply from 212.26.18.43: reach 0x07 offset 31.393002 delay 0.026659 status 0x24 strat 1 refid 0x47505300 rootdelay 0.000000
Fri Mar 28 22:47:27 2014 daemon.info sysinit: ntpd: reply from 108.61.56.35: reach 0x0f offset 31.388971 delay 0.191429 status 0x24 strat 2 refid 0x80040101 rootdelay 0.005249
Fri Mar 28 22:47:28 2014 daemon.info sysinit: ntpd: sent query to 212.26.18.43
Fri Mar 28 22:47:28 2014 daemon.info sysinit: ntpd: sent query to 212.26.18.41
Fri Mar 28 22:47:28 2014 daemon.info sysinit: ntpd: reply from 212.26.18.43: reach 0x0f offset 31.392697 delay 0.025398 status 0x24 strat 1 refid 0x47505300 rootdelay 0.000000
Fri Mar 28 22:47:28 2014 daemon.info sysinit: ntpd: reply from 212.26.18.41: reach 0x0f offset 31.393126 delay 0.026344 status 0x24 strat 1 refid 0x47505300 rootdelay 0.000000
Fri Mar 28 22:47:29 2014 daemon.info sysinit: ntpd: sent query to 212.26.18.43
Fri Mar 28 22:47:29 2014 daemon.info sysinit: ntpd: sent query to 108.61.56.35
Fri Mar 28 22:47:29 2014 daemon.info sysinit: ntpd: reply from 212.26.18.43: reach 0x1f offset 31.392298 delay 0.025096 status 0x24 strat 1 refid 0x47505300 rootdelay 0.000000
Fri Mar 28 22:47:30 2014 daemon.info sysinit: ntpd: reply from 108.61.56.35: reach 0x1f offset 31.388256 delay 0.191045 status 0x24 strat 2 refid 0x80040101 rootdelay 0.005249
Fri Mar 28 22:47:31 2014 daemon.info sysinit: ntpd: sent query to 212.26.18.43
Fri Mar 28 22:47:31 2014 daemon.info sysinit: ntpd: sent query to 212.26.18.41
Fri Mar 28 22:48:02 2014 daemon.info sysinit: ntpd: reply from 212.26.18.41: reach 0x1f offset 31.393134 delay 0.026418 status 0x24 strat 1 refid 0x47505300 rootdelay 0.000000
Fri Mar 28 22:48:02 2014 daemon.info sysinit: ntpd: setting clock to Fri Mar 28 22:48:02 CST 2014 (offset 31.392014s)
Fri Mar 28 22:48:02 2014 daemon.info sysinit: --bitmain-options 115200:32:8::: -o stratum.mining.eligius.st:3334 -O 1DiBRqnfKV7eSekycQ7VHVoZSzxG1nGSRW:123 -o eu-stratum.btcguild.com:3333 -O xref_1:123 -o stratum.btcguild.com:3333 -O xref_1:123 --api-listen --api-network
Fri Mar 28 22:48:02 2014 daemon.info sysinit: - init complete -
Fri Mar 28 22:48:02 2014 kern.info kernel: [   43.960000] bitmain 1-1.1:1.0: USB Bitmain asic #0 now disconnected
Fri Mar 28 22:49:04 2014 cron.info crond[576]: crond: USER root pid 859 cmd /usr/bin/cgminer-monitor
Fri Mar 28 22:51:01 2014 cron.info crond[576]: crond: USER root pid 881 cmd /usr/bin/cgminer-monitor
Fri Mar 28 22:54:01 2014 cron.info crond[576]: crond: USER root pid 903 cmd /usr/bin/cgminer-monitor

[xref]

UPDATE:

 -----------------------------------------------------
alias: -l not found
root@antMiner:~# cgminer -o stratum+tcp://stratum.mining.eligius.st:3334 -u 1DiB
RqnfKV7eSekycQ7VHVoZSzxG1nGSRW -p x
 [2014-03-28 22:59:13] Started cgminer 3.12.0
 [2014-03-28 22:59:13] No devices detected!
 [2014-03-28 22:59:13] Waiting for USB hotplug devices or press q to quit      
 [2014-03-28 22:59:13] Probing for an alive pool
[2014-03-28 22:59:14] Pool 0 difficulty changed to 15.999756                  
 [2014-03-28 22:59:14] Network diff set to 5.01G
(5s):0.000 (avg):0.000h/s | A:0  R:0  HW:0  WU:0.0/m


the bold part is new, never reached this part, so now no more connection problem, the only problem is device not found
this make me feel better, a problem solved, 1 more problem left

[kabopar]

UPDATE:

 -----------------------------------------------------
alias: -l not found
root@antMiner:~# cgminer -o stratum+tcp://stratum.mining.eligius.st:3334 -u 1DiB
RqnfKV7eSekycQ7VHVoZSzxG1nGSRW -p x
 [2014-03-28 22:59:13] Started cgminer 3.12.0
 [2014-03-28 22:59:13] No devices detected!
 [2014-03-28 22:59:13] Waiting for USB hotplug devices or press q to quit       
 [2014-03-28 22:59:13] Probing for an alive pool
[2014-03-28 22:59:14] Pool 0 difficulty changed to 15.999756                   
 [2014-03-28 22:59:14] Network diff set to 5.01G
(5s):0.000 (avg):0.000h/s | A:0  R:0  HW:0  WU:0.0/m


the bold part is new, never reached this part, so now no more connection problem, the only problem is device not found
this make me feel better, a problem solved, 1 more problem left

Looks like your mining software and network connections are running now, but there is no connection to the blades
"Fri Mar 28 22:48:02 2014 kern.info kernel: [   43.960000] bitmain 1-1.1:1.0: USB Bitmain asic #0 now disconnected"

What does it show at the lower part of your Status, Miner status screen?  Do you see something like

Chain#   ASIC#   Frequency   Fan   Temp
1        32      350
2       32      350

If not, then this is another potential sign that your blades are not 'seen' by the controller.

Perhaps there is a wiring/connection problem between the controller board and the blades - Turn the system off, disconnect from power - check that the cables between the controller and the blades are ok.  You could unplug the multi-wire connectors one at a time and inspect the contacts to make sure that none is pushed back inside the shell, then reconnect.  Another thing that you could try is to disconnect power to one blade at a time and run it with just one blade.
My impression is that all S1's are tested in the factory before shipping, so the problem occurred later or external to the Antminer itself.  What sort of power supply are you using?  Is each blade connected to a separate 12V rail or are you using a 'daisy chained' single rail with 2 PCI-e 6 pin connectors (the latter may not work, as a single rail might go into over-current protection).

Good luck

[alfabitcoin]

That line of disconect usb device is normal. I am more concrenred about pic update fail, i do not have it on my miner.
Also, no forwading state in kernal. Check network, and provide more data, what kind of connection you using ( wireless etc)
Also see firewall notice. Try with only one pool, use btcguild if you are in eu. We need more info to help you, syslog are not enough.
Do not wotty about bitmain device is now disconnected - its normal. Bitmain asic is registered, you can not detect device using cigminer comline. Cigminer hang out because there is network problems, or pool setings you use. Hashtest are fine. Imo you have network problems. Make hard restart on rooter as well miner, that often help.
Some member with teamviewer can help you.

Here is my kernal log if that help

[    0.000000] Linux version 3.10.12 (xll@ubuntu) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2013.05 r38031) ) #16 Fri Nov 29 10:51:49 CST 2013
[    0.000000] MyLoader: sysp=1bec2fee, boardp=fdd6ef6f, parts=fc031564
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 00019374 (MIPS 24Kc)
[    0.000000] SoC: Atheros AR9330 rev 1
[    0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x03ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x03ffffff]
[    0.000000] On node 0 totalpages: 16384
[    0.000000] free_area_init_node: node 0, pgdat 803005b0, node_mem_map 81000000
[    0.000000]   Normal zone: 128 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 16384 pages, LIFO batch:3
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc:

• 0

[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line:  board=TL-WR741ND-v4 console=ttyATH0,115200 rootfstype=squashfs,jffs2 noinitrd
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 61336k/65536k available (2187k kernel code, 4200k reserved, 588k data, 232k init, 0k highmem)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:51
[    0.080000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
[    0.080000] pid_max: default: 32768 minimum: 301
[    0.080000] Mount-cache hash table entries: 512
[    0.090000] NET: Registered protocol family 16
[    0.100000] MIPS: machine is TP-LINK TL-WR741ND v4
[    0.100000] MAC FF:FF:FF:FF:FF:FF
[    0.100000] MAC c8:ee:a6:00:35:55
[    0.560000] bio: create slab <bio-0> at 0
[    0.560000] Switching to clocksource MIPS
[    0.570000] NET: Registered protocol family 2
[    0.570000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[    0.580000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[    0.580000] TCP: Hash tables configured (established 512 bind 512)
[    0.590000] TCP: reno registered
[    0.590000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.600000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.610000] NET: Registered protocol family 1
[    0.610000] PCI: CLS 0 bytes, default 32
[    0.630000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.630000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.640000] msgmni has been set to 119
[    0.650000] io scheduler noop registered
[    0.650000] io scheduler deadline registered (default)
[    0.650000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[    0.660000] ar933x-uart: ttyATH0 at MMIO 0x18020000 (irq = 11) is a AR933X UART
[    0.670000] console [ttyATH0] enabled, bootconsole disabled
[    0.680000] ath79-spi ath79-spi: master is unqueued, this is deprecated
[    0.690000] m25p80 spi0.0: found s25fl064k, expected m25p80
[    0.690000] m25p80 spi0.0: s25fl064k (8192 Kbytes)
[    0.700000] 5 tp-link partitions found on MTD device spi0.0
[    0.700000] Creating 5 MTD partitions on "spi0.0":
[    0.710000] 0x000000000000-0x000000020000 : "u-boot"
[    0.710000] 0x000000020000-0x000000117d44 : "kernel"
[    0.720000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.730000] 0x000000117d44-0x0000007f0000 : "rootfs"
[    0.740000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.750000] mtd: partition "rootfs" set to be root filesystem
[    0.750000] mtd: partition "rootfs_data" created automatically, ofs=0x370000, len=0x480000
[    0.760000] 0x000000370000-0x0000007f0000 : "rootfs_data"
[    0.770000] 0x000000020000-0x0000007f0000 : "firmware"
[    0.770000] 0x0000007f0000-0x000000800000 : "art"
[    0.790000] libphy: ag71xx_mdio: probed
[    0.800000] eth0: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
[    1.350000] eth0: Found an AR7240/AR9330 built-in switch
[    2.390000] eth1: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
[    2.940000] ag71xx ag71xx.0 eth1: connected to PHY at ag71xx-mdio.1:04 [uid=004dd041, driver=Generic PHY]
[    2.950000] TCP: cubic registered
[    2.950000] NET: Registered protocol family 17
[    2.960000] 8021q: 802.1Q VLAN Support v1.8
[    2.970000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    2.980000] Freeing unused kernel memory: 232K (80316000 - 80350000)
[    5.810000] usbcore: registered new interface driver usbfs
[    5.810000] usbcore: registered new interface driver hub
[    5.820000] usbcore: registered new device driver usb
[    5.820000] usbcore: registered new interface driver bitmain
[    5.830000] hash ok
[    5.830000] hashtest OK
[    5.830000] bitmain-asic: success to register device
[    5.840000] usbcore: registered new interface driver bitmainbl
[    5.850000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    5.860000] ehci-platform: EHCI generic platform driver
[    5.860000] ehci-platform ehci-platform: EHCI Host Controller
[    5.870000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[    5.870000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[    5.900000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[    5.900000] hub 1-0:1.0: USB hub found
[    5.900000] hub 1-0:1.0: 1 port detected
[    6.230000] usb 1-1: new high-speed USB device number 2 using ehci-platform
[    6.380000] hub 1-1:1.0: USB hub found
[    6.380000] hub 1-1:1.0: 2 ports detected
[    6.670000] usb 1-1.1: new full-speed USB device number 3 using ehci-platform
[    6.800000] bitmain 1-1.1:1.0: USB Bitmain asic device now attached to USB Bitmain asic-0
[    6.810000] PIC microchip usb OK
[   10.570000] jffs2: notice: (327) jffs2_build_xattr_subsystem: complete building xattr subsystem, 26 of xdatum (0 unchecked, 25 orphan) and 39 of xref (0 dead, 25 orphan) found.
[   12.930000] hidraw: raw HID events driver (C) Jiri Kosina
[   12.950000] Loading modules backported from Linux version master-2013-06-27-0-gdcfa6d5
[   12.950000] Backport generated by backports.git backports-20130617-4-ge3220f5
[   12.970000] nf_conntrack version 0.5.0 (962 buckets, 3848 max)
[   13.010000] usbcore: registered new interface driver usbhid
[   13.020000] usbhid: USB HID core driver
[   13.020000] usbcore: registered new interface driver usbserial
[   13.030000] usbcore: registered new interface driver usbserial_generic
[   13.040000] usbserial: USB Serial support registered for generic
[   13.070000] xt_time: kernel timezone is -0000
[   13.090000] cfg80211: Calling CRDA to update world regulatory domain
[   13.090000] cfg80211: World regulatory domain updated:
[   13.100000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   13.110000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   13.110000] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   13.120000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   13.130000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   13.140000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   13.160000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   13.290000] ath: EEPROM regdomain: 0x0
[   13.290000] ath: EEPROM indicates default country code should be used
[   13.290000] ath: doing EEPROM country->regdmn map search
[   13.290000] ath: country maps to regdmn code: 0x3a
[   13.290000] ath: Country alpha2 being used: US
[   13.290000] ath: Regpair used: 0x3a
[   13.300000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[   13.310000] cfg80211: Calling CRDA for country: US
[   13.310000] cfg80211: Regulatory domain changed to country: US
[   13.320000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   13.330000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
[   13.330000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
[   13.340000] cfg80211:   (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   13.350000] cfg80211:   (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   13.360000] cfg80211:   (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   13.370000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
[   13.370000] ieee80211 phy0: Atheros AR9330 Rev:1 mem=0xb8100000, irq=2
[   18.240000] device eth0 entered promiscuous mode
[   18.270000] device eth1 entered promiscuous mode
[   18.270000] br-wan: port 1(eth1) entered forwarding state
[   18.280000] br-wan: port 1(eth1) entered forwarding state
[   18.280000] br-wan: port 1(eth1) entered disabled state
[   20.290000] eth1: link up (100Mbps/Full duplex)
[   20.290000] br-wan: port 1(eth1) entered forwarding state
[   20.300000] br-wan: port 1(eth1) entered forwarding state
[   22.300000] br-wan: port 1(eth1) entered forwarding state
[   39.090000] bitmain 1-1.1:1.0: USB Bitmain asic #0 now disconnected

[AngusCanine]

Done
did add the ntp servers, and did set custom dns to 8.8.8.8
actualy i did read his thread twice, not sure what exactly is wrong, the green lights that suppose to light while mining aren't lighting up at all

got mine to light up by switching pcie cables but it still wont mine hash rate is zero but pool info says alive? no antminer stats at all?

[kabopar]

Done
did add the ntp servers, and did set custom dns to 8.8.8.8
actualy i did read his thread twice, not sure what exactly is wrong, the green lights that suppose to light while mining aren't lighting up at all

got mine to light up by switching pcie cables but it still wont mine hash rate is zero but pool info says alive? no antminer stats at all?

What sort of power supply are you using?

[kabopar]

UPDATE:

 -----------------------------------------------------
alias: -l not found
root@antMiner:~# cgminer -o stratum+tcp://stratum.mining.eligius.st:3334 -u 1DiB
RqnfKV7eSekycQ7VHVoZSzxG1nGSRW -p x
 [2014-03-28 22:59:13] Started cgminer 3.12.0
 [2014-03-28 22:59:13] No devices detected!
 [2014-03-28 22:59:13] Waiting for USB hotplug devices or press q to quit      
 [2014-03-28 22:59:13] Probing for an alive pool
[2014-03-28 22:59:14] Pool 0 difficulty changed to 15.999756                  
 [2014-03-28 22:59:14] Network diff set to 5.01G
(5s):0.000 (avg):0.000h/s | A:0  R:0  HW:0  WU:0.0/m


the bold part is new, never reached this part, so now no more connection problem, the only problem is device not found
this make me feel better, a problem solved, 1 more problem left

xref,
Did you make any further progress?

[AngusCanine]

Done
did add the ntp servers, and did set custom dns to 8.8.8.8
actualy i did read his thread twice, not sure what exactly is wrong, the green lights that suppose to light while mining aren't lighting up at all

got mine to light up by switching pcie cables but it still wont mine hash rate is zero but pool info says alive? no antminer stats at all?

What sort of power supply are you using?

antec earthwatts 650, 80 plus bronze, dual 12v rails

[kabopar]

Done
did add the ntp servers, and did set custom dns to 8.8.8.8
actualy i did read his thread twice, not sure what exactly is wrong, the green lights that suppose to light while mining aren't lighting up at all

got mine to light up by switching pcie cables but it still wont mine hash rate is zero but pool info says alive? no antminer stats at all?

What sort of power supply are you using?

antec earthwatts 650, 80 plus bronze, dual 12v rails

I looked up this power supply on Antec's web site, however it doesn't specify the current on the 12V rails.  I'm using the Antec TruePower TPC-650 and it works fine.  Do you know what is the current spec on your PS?
In my setup the connection to the antminer is through the WAN, not the LAN.  How did you setup your connection?
Are you sure that you entered your miner credentials correctly?
How is your router setup in relation to the Antminer?  (as the WAN address is fixed, many routers allow a pre-allocation of an IP address to a specific mac address, you can use this feature to get your router to support a fixed IP for the Antminer.  Your Router's IP address range needs to cover the Antminer's, so if you leave the Antminer WAN at the factory default 192.168.1.99 your router needs to cover for example 192.168.1.1 to 192.168.1.100, typically in this case your router (the 'gateway') would be at 192.168.1.1).

Good luck