i just bought a new OEMGMINER Antminer S19k Pro XTh Asic Miner XW Bitmain and connected it to Nicehash.
Connection seems fine, hashrate starts a bit and then Real Hash Rate stays at 0.
In the end of the logs are some errors but i cant tell what is it about.
[ 0.000000@0] Booting Linux on physical CPU 0x0
[ 0.000000@0] Linux version 4.9.113 (jenkins@nomd-nomd-fwc-bj) (gcc version 6.3.1 20170109 (Linaro GCC 6.3-2017.02) ) #1 SMP PREEMPT Tue Apr 9 12:23:58 CST 2024
[ 0.000000@0] Boot CPU: AArch64 Processor [410fd034]
[ 0.000000@0] earlycon: aml_uart0 at MMIO 0x00000000ff803000 (options '')
[ 0.000000@0] bootconsole [aml_uart0] enabled
[ 0.000000@0] efi: Getting EFI parameters from FDT:
[ 0.000000@0] efi: UEFI not found.
[ 0.000000@0] 07400000 - 07500000, 1024 KB, ramoops@0x07400000
[ 0.000000@0] __reserved_mem_alloc_size, start:0x0000000005000000, end:0x0000000005400000, len:4 MiB
[ 0.000000@0] 05000000 - 05400000, 4096 KB, linux,secmon
[ 0.000000@0] __reserved_mem_alloc_size, start:0x000000003e000000, end:0x0000000040000000, len:32 MiB
[ 0.000000@0] failed to allocate memory for node linux,meson-fb, size:32 MB
[ 0.000000@0] cma: Reserved 16 MiB at 0x000000000f000000
[ 0.000000@0] On node 0 totalpages: 65536
[ 0.000000@0] DMA zone: 1024 pages used for memmap
[ 0.000000@0] DMA zone: 0 pages reserved
[ 0.000000@0] DMA zone: 65536 pages, LIFO batch:15
[ 0.000000@0] psci: probing for conduit method from DT.
[ 0.000000@0] psci: PSCIv1.0 detected in firmware.
[ 0.000000@0] psci: Using standard PSCI v0.2 function IDs
[ 0.000000@0] psci: MIGRATE_INFO_TYPE not supported.
[ 0.000000@0] psci: SMC Calling Convention v1.1
[ 0.000000@0] percpu: Embedded 25 pages/cpu @ffffffc00ef53000 s64536 r8192 d29672 u102400
[ 0.000000@0] pcpu-alloc: s64536 r8192 d29672 u102400 alloc=25*4096
[ 0.000000@0] pcpu-alloc:
[ 0.000000@0] Detected VIPT I-cache on CPU0
[ 0.000000@0] CPU features: enabling workaround for ARM erratum 845719
[ 0.000000@0] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 64512
[ 0.000000@0] Kernel command line: init=/init console=ttyS0,115200 no_console_suspend earlycon=aml_uart,0xff803000 ramoops.pstore_en=1 ramoops.record_size=0x8000 ramoops.console_size=0x4000 logo=,loaded,androidboot.selinux=enforcing androidboot.firstboot=1 jtag=disable androidboot.hardware=amlogic androidboot.bootloader=U-Boot 2015.01 androidboot.build.expect.baseband=N/A androidboot.serialno=1234567890 androidboot.rpmb_state=0 rootfstype=ramfs init=/sbin/init
[ 0.000000@0] PID hash table entries: 1024 (order: 1, 8192 bytes)
[ 0.000000@0] Dentry cache hash table entries: 32768 (order: 6, 262144 bytes)
[ 0.000000@0] Inode-cache hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.000000@0] Memory: 211560K/262144K available (8764K kernel code, 1194K rwdata, 2424K rodata, 3648K init, 1017K bss, 30104K reserved, 20480K cma-reserved)
[ 0.000000@0] Virtual kernel memory layout:
[ 0.000000@0] modules : 0xffffff8000000000 - 0xffffff8008000000 ( 128 MB)
[ 0.000000@0] vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000 ( 250 GB)
[ 0.000000@0] .text : 0xffffff8009080000 - 0xffffff8009910000 ( 8768 KB)
[ 0.000000@0] .rodata : 0xffffff8009910000 - 0xffffff8009b80000 ( 2496 KB)
[ 0.000000@0] .init : 0xffffff8009b80000 - 0xffffff8009f10000 ( 3648 KB)
[ 0.000000@0] .data : 0xffffff8009f10000 - 0xffffff800a03aa00 ( 1195 KB)
[ 0.000000@0] .bss : 0xffffff800a03aa00 - 0xffffff800a139034 ( 1018 KB)
[ 0.000000@0] fixed : 0xffffffbefe7fb000 - 0xffffffbefec00000 ( 4116 KB)
[ 0.000000@0] PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000 ( 16 MB)
[ 0.000000@0] vmemmap : 0xffffffbf00000000 - 0xffffffc000000000 ( 4 GB maximum)
[ 0.000000@0] 0xffffffbf00000000 - 0xffffffbf00400000 ( 4 MB actual)
[ 0.000000@0] memory : 0xffffffc000000000 - 0xffffffc010000000 ( 256 MB)
[ 0.000000@0] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000@0] Preemptible hierarchical RCU implementation.
[ 0.000000@0] Build-time adjustment of leaf fanout to 64.
[ 0.000000@0] RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
[ 0.000000@0] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4
[ 0.000000@0] NR_IRQS:64 nr_irqs:64 0
[ 0.000000@0] irq_meson_gpio: 100 to 8 gpio interrupt mux initialized
[ 0.000000@0] axg_aoclkc_init: register ao clk ok!
[ 0.000000@0] axg_amlogic_init_sdemmc: register amlogic sdemmc clk
[ 0.000000@0] axg_amlogic_init_sdemmc: register amlogic sdemmc clk
[ 0.000000@0] axg_amlogic_init_media: register meson media clk
[ 0.000000@0] axg_amlogic_init_misc: register amlogic axg misc clks
[ 0.000000@0] axg_amlogic_init_misc: register amlogic sdemmc clk
[ 0.000000@0] axg_clkc_init initialization complete
[ 0.000000@0] arm_arch_timer: Architected cp15 timer(s) running at 24.00MHz (phys).
[ 0.000000@0] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[ 0.000003@0] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[ 0.008252@0] meson_bc_timer: mclk->mux_reg =ffffff800800a190,mclk->reg =ffffff800800c194
[ 0.016904@0] Console: colour dummy device 80x25
[ 0.021107@0] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000)
[ 0.031586@0] pid_max: default: 32768 minimum: 301
[ 0.036436@0] thread_stack_cache_init, vmap:ffffffc00e5af600, bitmap:ffffffc00e5a3000, cache page:e5e0
[ 0.045773@0] thread_stack_cache_init, allocation vm area:ffffffc00e5d94c0, addr:ffffff8020000000, size:20001000
[ 0.056006@0] cpu 0, vmap_stack:[ffffffc00ef5c960-ffffffc00ef60950]
[ 0.062305@0] cpu 0, irq_stack: [ffffffc00ef53060-ffffffc00ef57050]
[ 0.068604@0] cpu 1, vmap_stack:[ffffffc00ef75960-ffffffc00ef79950]
[ 0.074904@0] cpu 1, irq_stack: [ffffffc00ef6c060-ffffffc00ef70050]
[ 0.081204@0] cpu 2, vmap_stack:[ffffffc00ef8e960-ffffffc00ef92950]
[ 0.087504@0] cpu 2, irq_stack: [ffffffc00ef85060-ffffffc00ef89050]
[ 0.093804@0] cpu 3, vmap_stack:[ffffffc00efa7960-ffffffc00efab950]
[ 0.100104@0] cpu 3, irq_stack: [ffffffc00ef9e060-ffffffc00efa2050]
[ 0.106464@0] Security Framework initialized
[ 0.110696@0] SELinux: Initializing.
[ 0.114389@0] SELinux: Starting in permissive mode
[ 0.114427@0] Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
[ 0.121108@0] Mountpoint-cache hash table entries: 512 (order: 0, 4096 bytes)
[ 0.128836@0] ftrace: allocating 30061 entries in 118 pages
[ 0.186533@0] sched-energy: CPU device node has no sched-energy-costs
[ 0.187348@0] CPU0: update cpu_capacity 1024
[ 0.191677@0] ASID allocator initialised with 32768 entries
[ 0.229815@0] secmon: can't fine clear_range
[ 0.230018@0] EFI services will not be available.
[ 0.233287@0] Meson chip version = RevC (25:C - 23:0)
[ 0.266959@1] Detected VIPT I-cache on CPU1
[ 0.267018@1] CPU1: update cpu_capacity 1024
[ 0.267021@1] CPU1: Booted secondary processor [410fd034]
[ 0.295019@2] Detected VIPT I-cache on CPU2
[ 0.295071@2] CPU2: update cpu_capacity 1024
[ 0.295073@2] CPU2: Booted secondary processor [410fd034]
[ 0.323085@3] Detected VIPT I-cache on CPU3
[ 0.323133@3] CPU3: update cpu_capacity 1024
[ 0.323136@3] CPU3: Booted secondary processor [410fd034]
[ 0.323222@0] Brought up 4 CPUs
[ 0.362443@0] SMP: Total of 4 processors activated.
[ 0.367352@0] CPU features: detected feature: 32-bit EL0 Support
[ 0.373388@0] CPU features: detected feature: Kernel page table isolation (KPTI)
[ 0.383944@0] CPU: All CPU(s) started at EL2
[ 0.385127@0] alternatives: patching kernel code
[ 0.390430@1] addr:ffffff802007be10 is in kernel, size fix 4096->10, data:mode=0755
[ 0.397648@0] devtmpfs: initialized
[ 0.412657@0] DMI not present or invalid.
[ 0.413064@0] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.421028@0] futex hash table entries: 1024 (order: 4, 65536 bytes)
[ 0.427605@0] pinctrl core: initialized pinctrl subsystem
[ 0.433990@0] NET: Registered protocol family 16
[ 0.457557@0] cpuidle: using governor menu
[ 0.458063@0] vdso: 2 pages (1 code @ ffffff8009917000, 1 data @ ffffff8009f14000)
[ 0.463669@0] hw-breakpoint: found 6 breakpoint and 2 watchpoint registers.
[ 0.471066@0] DMA: preallocated 256 KiB pool for atomic allocations
[ 0.477210@0] clkmsr: clkmsr: driver init
[ 0.481268@0] aml_watch_point_probe, in, wp:2
[ 0.486695@0] pstore: using zlib compression
[ 0.490111@0] console [pstore-1] enabled
[ 0.493545@0] pstore: Registered ramoops as persistent store backend
[ 0.499952@0] ramoops: attached 0x100000@0x7400000, ecc: 0/0
[ 0.514322@0] aml_iomap: amlogic iomap probe done
[ 0.521275@0] clkmsr: msr_clk_reg0=ffffff800817e004,msr_clk_reg2=ffffff80081d100c
[ 0.523208@0] clkmsr ffd18004.meson_clk_msr: failed to get msr ring reg0
[ 0.623483@0] usbcore: registered new interface driver usbfs
[ 0.623649@0] usbcore: registered new interface driver hub
[ 0.629248@0] usbcore: registered new device driver usb
[ 0.634594@0] pps_core: LinuxPPS API ver. 1 registered
[ 0.639480@0] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <
giometti@linux.it>
[ 0.648882@0] PTP clock support registered
[ 0.653214@0] dmi: Firmware registration failed.
[ 0.658189@0] secmon: reserve_mem_size:0x300000
[ 0.662243@0] secmon secmon: assigned reserved memory node linux,secmon
[ 0.669134@0] secmon: get page:ffffffbf00140000, 5000
[ 0.673855@0] secmon: share in base: 0xffffffc0050fe000, share out base: 0xffffffc0050ff000
[ 0.682244@0] secmon: phy_in_base: 0x50fe000, phy_out_base: 0x50ff000
[ 0.690123@0] NetLabel: Initializing
[ 0.692294@0] NetLabel: domain hash size = 128
[ 0.696887@0] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.702111@0] NetLabel: unlabeled traffic allowed by default
[ 0.708756@0] clocksource: Switched to clocksource arch_sys_counter
[ 0.835544@0] VFS: Disk quotas dquot_6.6.0
[ 0.835692@0] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.861608@2] NET: Registered protocol family 2
[ 0.862652@2] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.867859@2] TCP bind hash table entries: 2048 (order: 3, 32768 bytes)
[ 0.874512@2] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.881116@2] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.887064@2] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.893800@2] NET: Registered protocol family 1
[ 0.898757@2] RPC: Registered named UNIX socket transport module.
[ 0.904197@2] RPC: Registered udp transport module.
[ 0.909085@2] RPC: Registered tcp transport module.
[ 0.913974@2] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.923147@2] Unpacking initramfs...
[ 1.433567@0] Initramfs unpacking failed: junk in compressed archive
[ 1.440490@0] Freeing initrd memory: 6700K
[ 1.441423@0] hw perfevents: clusterb_enabled = 0
[ 1.443673@0] hw perfevents: cpumasks 0xf, 0x0
[ 1.448225@0] hw perfevents: cluster A irq = 7
[ 1.452818@0] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available
[ 1.462870@0] audit: initializing netlink subsys (disabled)
[ 1.466282@0] audit: type=2000 audit(1.280:1): initialized
[ 1.473573@0] workingset: timestamp_bits=62 max_order=16 bucket_order=0
[ 1.497718@0] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 1.500596@0] NFS: Registering the id_resolver key type
[ 1.503428@0] Key type id_resolver registered
[ 1.507746@0] Key type id_legacy registered
[ 1.512360@0] fuse init (API version 7.26)
[ 1.517807@0] SELinux: Registering netfilter hooks
[ 1.524172@0] NET: Registered protocol family 38
[ 1.524235@0] Key type asymmetric registered
[ 1.527476@0] Asymmetric key parser 'x509' registered
[ 1.532982@0] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)
[ 1.540265@0] io scheduler noop registered (default)
[ 1.545150@0] io scheduler deadline registered
[ 1.549941@0] io scheduler cfq registered
[ 1.570474@2] random: fast init done
[ 1.570573@2] random: crng init done
[ 1.571016@0] Unable to detect cache hierarchy for CPU 0
[ 1.616840@0] loop: module loaded
[ 1.622368@0] zram: Added device: zram0
[ 1.622763@0] mtdoops: mtd device (mtddev=name/number) must be supplied
[ 1.628221@0] libphy: Fixed MDIO Bus: probed
[ 1.632333@0] tun: Universal TUN/TAP device driver, 1.6
[ 1.636812@0] tun: (C) 1999-2004 Max Krasnyansky <
maxk@qualcomm.com>
[ 1.645017@0] ee eth reset:Addr = ffffff80081fd008
[ 1.652433@0] meson6-dwmac ff3f0000.ethernet: no reset control found
[ 1.654471@0] stmmac - user ID: 0x11, Synopsys ID: 0x37
[ 1.659707@0] Ring mode enabled
[ 1.662934@0] DMA HW capability register supported
[ 1.667657@0] Normal descriptors
[ 1.670981@0] RX Checksum Offload Engine supported
[ 1.675881@0] COE Type 2
[ 1.678505@0] TX Checksum insertion supported
[ 1.682968@0] Wake-Up On Lan supported
[ 1.686911@0] Enable RX Mitigation via HW Watchdog Timer
[ 1.700380@0] libphy: stmmac: probed
[ 1.700432@0] eth%d: PHY ID 0007c0f1 at 0 IRQ POLL (stmmac-0:00) active
[ 1.706861@0] PPP generic driver version 2.4.2
[ 1.709871@0] PPP BSD Compression module registered
[ 1.714371@0] PPP Deflate Compression module registered
[ 1.719624@0] PPP MPPE Compression module registered
[ 1.724580@0] NET: Registered protocol family 24
[ 1.730062@0] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.735977@0] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.743044@0] usbcore: registered new interface driver cdc_acm
[ 1.748221@0] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 1.756655@0] usbcore: registered new interface driver usbserial
[ 1.763283@0] mousedev: PS/2 mouse device common for all mice
[ 1.768803@0] usbcore: registered new interface driver xpad
[ 1.774156@0] i2c /dev entries driver
[ 1.778886@0] cpu cpu0: bL_cpufreq_init: CPU 0 initialized
[ 1.783188@0] arm_big_little: bL_cpufreq_register: Registered platform driver: scpi
[ 1.794159@0] ff803000.serial: clock gate not found
[ 1.795690@0] meson_uart ff803000.serial: ==uart0 reg addr = ffffff800830d000
[ 1.802918@0] ff803000.serial: ttyS0 at MMIO 0xff803000 (irq = 13, base_baud = 1500000) is a meson_uart
[ 1.817840@0] meson_uart ff803000.serial: ttyS0 use xtal(24M) 24000000 change 0 to 115200
[ 1.820527@0] console [ttyS0] enabled
[ 1.827760@0] bootconsole [aml_uart0] disabled
[ 1.837447@2] ff804000.serial: clock gate not found
[ 1.841550@2] meson_uart ff804000.serial: ==uart3 reg addr = ffffff8008321000
[ 1.848663@2] ff804000.serial: ttyS3 at MMIO 0xff804000 (irq = 14, base_baud = 1500000) is a meson_uart
[ 1.859020@1] meson_uart ffd24000.serial: ==uart1 reg addr = ffffff8008323000
[ 1.865171@1] ffd24000.serial: ttyS1 at MMIO 0xffd24000 (irq = 25, base_baud = 1500000) is a meson_uart
[ 1.875320@0] meson_uart ffd23000.serial: ==uart2 reg addr = ffffff8008325000
[ 1.881626@0] ffd23000.serial: ttyS2 at MMIO 0xffd23000 (irq = 26, base_baud = 1500000) is a meson_uart
[ 1.892566@2] amlogic-new-usb2 ffe09000.usb2phy: USB2 phy probe:phy_mem:0xffe09000, iomap phy_base:0xffffff8008348000
[ 1.901891@2] amlogic-new-usb3 ffe09080.usb3phy: This phy has no usb port
[ 1.908389@2] amlogic-new-usb3 ffe09080.usb3phy: USB3 phy probe:phy_mem:0xffe09080, iomap phy_base:0xffffff800834c080
[ 1.923577@1] i2c i2c-1: of_i2c: modalias failure on /soc/aobus@ff800000/i2c@5000/mcu6350@40
[ 1.927202@1] i2c i2c-1: Failed to create I2C device for /soc/aobus@ff800000/i2c@5000/mcu6350@40
[ 1.939583@1] aml_dma ff63e000.aml_dma: Aml dma
[ 1.942740@1] aml_aes_dma ff63e000.aml_dma:aml_aes: Aml AES_dma
[ 1.947687@1] aml_sha_dma ff63e000.aml_dma:aml_sha: Aml SHA1/SHA224/SHA256 dma
[ 1.954101@1] efusekeynum: 4
[ 1.956387@1] efusekeyname: mac offset: 0 size: 6
[ 1.962844@1] efusekeyname: mac_bt offset: 6 size: 6
[ 1.969237@1] efusekeyname: mac_wifi offset: 12 size: 6
[ 1.975646@1] efusekeyname: usid offset: 18 size: 16
[ 1.982484@1] efuse efuse: probe OK!
[ 1.987926@1] meson-mmc: mmc driver version: 3.02, 2017-05-15: New Emmc Host Controller
[ 1.995149@1] meson-mmc: >>>>>>>>hostbase ffffff8008358000, dmode
[ 2.000246@1] meson-mmc: actual_clock :400000, HHI_nand: 0x80
[ 2.005453@1] meson-mmc: [meson_mmc_clk_set_rate_v3] after clock: 0x1000033c
[ 2.048906@1] meson-mmc: meson_mmc_probe() : success!
[ 2.049165@1] amlogic mtd driver init
[ 2.053218@1] prase_get_dtb_nand_parameter:128,parse dts start
[ 2.057977@1] bl mode descrete
[ 2.060855@1] fip_copies 4
[ 2.063518@1] fip_size 0x200000
[ 2.066659@1] nand_clk_ctrl 0xffe07000
[ 2.070383@1] prase_get_dtb_nand_parameter:234,parse dts end
[ 2.076048@1] nand_clk_ctrl 0xffe07000
[ 2.079771@1] nand register base ffffff80083df800, nand clock register ffffff80083e1000
[ 2.088508@1] plat->aml_nand_device ffffff800a005c10
[ 2.092681@1] m3_nand_probe() aml_nand_device ffffff800a005c10
[ 2.098737@1] NAND device id: 2c da 90 95 6 0
[ 2.102807@1] NAND device: Manufacturer ID:
[ 2.106872@1] 0x2c, Chip ID: 0x2c (Micron A revision NAND 2Gib MT29F2G08-A)
[ 2.113916@1] oob_fill_cnt =32 oob_size =64, bch_bytes =14
[ 2.119348@1] ecc mode:6 ecc_page_num=2 eep_need_oobsize=16
[ 2.124896@1] plane_num=1 writesize=0x800 ecc.size=0x200 bch_mode=1
[ 2.131141@1] mtd->oobavail: 0x8
[ 2.134540@1] aml_nand_init 2119: plat-name:bootloader
[ 2.139461@1] Creating 1 MTD partitions on "bootloader":
[ 2.144760@1] 0x000000000000-0x000000200000 : "bootloader"
[ 2.153513@0] bootloader initialized ok
[ 2.154010@0] plat->aml_nand_device ffffff800a005c10
[ 2.158981@0] m3_nand_probe() aml_nand_device ffffff800a005c10
[ 2.165127@0] NAND device id: 2c da 90 95 6 0
[ 2.169144@0] NAND device: Manufacturer ID:
[ 2.173182@0] 0x2c, Chip ID: 0x2c (Micron A revision NAND 2Gib MT29F2G08-A)
[ 2.180215@0] oob_fill_cnt =32 oob_size =64, bch_bytes =14
[ 2.185657@0] ecc mode:6 ecc_page_num=2 eep_need_oobsize=16
[ 2.191200@0] plane_num=1 writesize=0x800 ecc.size=0x200 bch_mode=1
[ 2.197450@0] mtd->oobavail: 0x8
[ 2.200913@0] aml_nand_init 2119: plat-name:nandnormal
[ 2.205801@0] bbt_start=20
[ 2.208423@0] env_start=24
[ 2.211130@0] key_start=32
[ 2.213814@0] dtb_start=40
[ 2.216482@0] ddr_start=44
[ 2.219188@0] nbbt: info size=0x800 max_scan_blk=24, start_blk=20
[ 2.225686@0] get_free_node 43: bitmap=0
[ 2.229156@0] get_free_node 55: bitmap=1
[ 2.233248@0] get_free_node 43: bitmap=1
[ 2.236955@0] get_free_node 55: bitmap=3
[ 2.241046@0] get_free_node 43: bitmap=3
[ 2.244755@0] get_free_node 55: bitmap=7
[ 2.248638@0] nbbt : phy_blk_addr=20, ec=0, phy_page_addr=0, timestamp=1
[ 2.255326@0] nbbt free list:
[ 2.258274@0] blockN=21, ec=-1, dirty_flag=0
[ 2.262520@0] blockN=22, ec=-1, dirty_flag=0
[ 2.266766@0] blockN=23, ec=-1, dirty_flag=0
[ 2.271014@0] aml_nand_scan_rsv_info 1141: page_num=1
[ 2.276423@0] nbbt valid addr: 280000
[ 2.279683@0] aml_nand_bbt_check 1306 bbt is valid, reading.
[ 2.285316@0] aml_nand_read_rsv_info:423,read nbbt info at 280000
[ 2.291575@0] nenv: info size=0x10000 max_scan_blk=32, start_blk=24
[ 2.298004@0] get_free_node 43: bitmap=7
[ 2.301522@0] get_free_node 55: bitmap=f
[ 2.305613@0] get_free_node 43: bitmap=f
[ 2.309321@0] get_free_node 55: bitmap=1f
[ 2.313499@0] get_free_node 43: bitmap=1f
[ 2.317295@0] get_free_node 55: bitmap=3f
[ 2.321473@0] get_free_node 43: bitmap=3f
[ 2.325268@0] get_free_node 55: bitmap=7f
[ 2.329446@0] get_free_node 43: bitmap=7f
[ 2.333242@0] get_free_node 55: bitmap=ff
[ 2.337419@0] get_free_node 43: bitmap=ff
[ 2.341215@0] get_free_node 55: bitmap=1ff
[ 2.345479@0] get_free_node 43: bitmap=1ff
[ 2.349361@0] get_free_node 55: bitmap=3ff
[ 2.353435@0] nenv : phy_blk_addr=24, ec=0, phy_page_addr=0, timestamp=1
[ 2.360105@0] nenv free list:
[ 2.363053@0] blockN=25, ec=-1, dirty_flag=0
[ 2.367300@0] blockN=26, ec=-1, dirty_flag=0
[ 2.371546@0] blockN=27, ec=-1, dirty_flag=0
[ 2.375793@0] blockN=28, ec=-1, dirty_flag=0
[ 2.380040@0] blockN=29, ec=-1, dirty_flag=0
[ 2.384286@0] blockN=30, ec=-1, dirty_flag=0
[ 2.388533@0] blockN=31, ec=-1, dirty_flag=0
[ 2.392780@0] aml_nand_scan_rsv_info 1141: page_num=32
[ 2.410027@0] nenv valid addr: 310000
[ 2.410060@0] nkey: info size=0x8000 max_scan_blk=40, start_blk=32
[ 2.414425@0] get_free_node 43: bitmap=3ff
[ 2.418306@0] get_free_node 55: bitmap=7ff
[ 2.422570@0] get_free_node 43: bitmap=7ff
[ 2.426452@0] get_free_node 55: bitmap=fff
[ 2.430717@0] get_free_node 43: bitmap=fff
[ 2.434598@0] get_free_node 55: bitmap=1fff
[ 2.438950@0] get_free_node 43: bitmap=1fff
[ 2.442918@0] get_free_node 55: bitmap=3fff
[ 2.447269@0] get_free_node 43: bitmap=3fff
[ 2.451238@0] get_free_node 55: bitmap=7fff
[ 2.455589@0] get_free_node 43: bitmap=7fff
[ 2.459558@0] get_free_node 55: bitmap=ffff
[ 2.463909@0] get_free_node 43: bitmap=ffff
[ 2.467878@0] get_free_node 55: bitmap=1ffff
[ 2.472316@0] get_free_node 43: bitmap=1ffff
[ 2.476372@0] get_free_node 55: bitmap=3ffff
[ 2.480618@0] nkey : phy_blk_addr=-1, ec=0, phy_page_addr=0, timestamp=0
[ 2.487289@0] nkey free list:
[ 2.490236@0] blockN=32, ec=-1, dirty_flag=0
[ 2.494483@0] blockN=33, ec=-1, dirty_flag=0
[ 2.498730@0] blockN=34, ec=-1, dirty_flag=0
[ 2.502976@0] blockN=35, ec=-1, dirty_flag=0
[ 2.507223@0] blockN=36, ec=-1, dirty_flag=0
[ 2.511470@0] blockN=37, ec=-1, dirty_flag=0
[ 2.515716@0] blockN=38, ec=-1, dirty_flag=0
[ 2.519963@0] blockN=39, ec=-1, dirty_flag=0
[ 2.524210@0] aml_nand_scan_rsv_info 1141: page_num=16
[ 2.529323@0] nkey valid addr: fffffffffffe0000
[ 2.533830@0] aml_nand_key_check 1251 NO key exist
[ 2.538598@0] ndtb: info size=0x20000 max_scan_blk=44, start_blk=40
[ 2.545220@0] get_free_node 43: bitmap=3ffff
[ 2.549085@0] get_free_node 55: bitmap=7ffff
[ 2.553522@0] get_free_node 43: bitmap=7ffff
[ 2.557579@0] get_free_node 55: bitmap=fffff
[ 2.562016@0] get_free_node 43: bitmap=fffff
[ 2.566072@0] get_free_node 55: bitmap=1fffff
[ 2.570405@0] ndtb : phy_blk_addr=40, ec=0, phy_page_addr=0, timestamp=1
[ 2.577076@0] ndtb free list:
[ 2.580006@0] blockN=41, ec=-1, dirty_flag=0
[ 2.584270@0] blockN=42, ec=-1, dirty_flag=0
[ 2.588566@0] blockN=43, ec=-1, dirty_flag=0
[ 2.592766@0] aml_nand_scan_rsv_info 1141: page_num=64
[ 2.610002@0] ndtb valid addr: 500000
[ 2.610036@0] nddr: info size=0x20000 max_scan_blk=46, start_blk=44
[ 2.614485@0] get_free_node 43: bitmap=1fffff
[ 2.618626@0] get_free_node 55: bitmap=3fffff
[ 2.623151@0] get_free_node 43: bitmap=3fffff
[ 2.627293@0] get_free_node 55: bitmap=7fffff
[ 2.631626@0] nddr : phy_blk_addr=-1, ec=0, phy_page_addr=0, timestamp=0
[ 2.638297@0] nddr free list:
[ 2.641244@0] blockN=44, ec=-1, dirty_flag=0
[ 2.645491@0] blockN=45, ec=-1, dirty_flag=0
[ 2.649738@0] aml_nand_scan_rsv_info 1141: page_num=64
[ 2.654851@0] nddr valid addr: fffffffffffe0000
[ 2.659358@0] aml_nand_ddr_check 1281 NO ddr exist
[ 2.664128@0] tpl: off 8388608, size 8388608
[ 2.795692@0] Creating 6 MTD partitions on "nandnormal":
[ 2.795757@0] 0x000000800000-0x000001000000 : "tpl"
[ 2.807348@1] 0x000001000000-0x000001200000 : "misc"
[ 2.810621@3] 0x000001200000-0x000002200000 : "recovery"
[ 2.822501@1] 0x000002200000-0x000004200000 : "boot"
[ 2.841612@1] 0x000004200000-0x000004700000 : "config"
[ 2.846258@1] 0x000004700000-0x000010000000 : "nvdata"
[ 2.947264@3] nandnormal initialized ok
[ 2.947373@3] aml_ubootenv_init: register env chardev
[ 2.950908@3] aml_ubootenv_init: register env chardev OK
[ 2.955949@3] amlnf_dtb_init: register dtb cdev
[ 2.960650@3] amlnf_dtb_init: register dtd cdev OK
[ 2.965121@3] mtd_nand_probe 267 , err = 0
[ 2.970235@0] aml_vrtc rtc: rtc core: registered aml_vrtc as rtc0
[ 2.975678@0] input: aml_vkeypad as /devices/platform/rtc/input/input0
[ 2.982672@3] unifykey: storage in base: 0xffffffc005000000
[ 2.987317@3] unifykey: storage out base: 0xffffffc005040000
[ 2.992906@3] unifykey: storage block base: 0xffffffc005080000
[ 2.998717@3] unifykey: probe done!
[ 3.002914@3] unifykey: no efuse-version set, use default value: -1
[ 3.008444@3] unifykey: key unify config unifykey-num is 6
[ 3.013954@3] unifykey: key unify fact unifykey-num is 6
[ 3.019177@3] unifykey: unifykey_devno: f200000
[ 3.024142@2] unifykey: device unifykeys created ok
[ 3.028679@2] unifykey: aml_unifykeys_init done!
[ 3.033565@2] sysled: module init
[ 3.037070@2] meson_wdt ffd0f0d0.watchdog: start watchdog
[ 3.041814@2] meson_wdt ffd0f0d0.watchdog: creat work queue for watch dog
[ 3.049255@1] meson_wdt ffd0f0d0.watchdog: AML Watchdog Timer probed done
[ 3.058096@2] dmc_monitor_probe
[ 3.060426@2] defendkey defendkey: Reserved memory is not enough!
[ 3.064545@2] defendkey: probe of defendkey failed with error -22
[ 3.070876@2] GACT probability NOT on
[ 3.074224@2] Mirror/redirect action on
[ 3.078032@2] u32 classifier
[ 3.080871@2] Actions configured
[ 3.084412@2] Netfilter messages via NETLINK v0.30.
[ 3.089704@2] nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
[ 3.095906@2] ctnetlink v0.93: registering with nfnetlink.
[ 3.101725@2] xt_time: kernel timezone is -0000
[ 3.105488@2] ipip: IPv4 and MPLS over IPv4 tunneling driver
[ 3.112135@2] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 3.116869@2] arp_tables: arp_tables: (C) 2002 David S. Miller
[ 3.122300@2] Initializing XFRM netlink socket
[ 3.127837@2] NET: Registered protocol family 10
[ 3.133784@2] mip6: Mobile IPv6
[ 3.134377@2] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 3.140363@2] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 3.148323@2] NET: Registered protocol family 17
[ 3.150629@2] NET: Registered protocol family 15
[ 3.155226@2] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 3.168386@2] l2tp_core: L2TP core driver, V2.0
[ 3.172814@2] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[ 3.177678@2] l2tp_ip: L2TP IP encapsulation support (L2TPv3)
[ 3.183429@2] l2tp_netlink: L2TP netlink interface
[ 3.188227@2] l2tp_eth: L2TP ethernet pseudowire support (L2TPv3)
[ 3.194298@2] l2tp_debugfs: L2TP debugfs support
[ 3.198847@2] l2tp_ip6: L2TP IP encapsulation support for IPv6 (L2TPv3)
[ 3.205476@2] NET: Registered protocol family 35
[ 3.210413@2] Key type dns_resolver registered
[ 3.215007@2] Registered swp emulation handler
[ 3.218870@2] Registered cp15_barrier emulation handler
[ 3.224061@2] Registered setend emulation handler
[ 3.228818@2] disable EAS feature
[ 3.233404@2] registered taskstats version 1
[ 3.250258@0] dwc3 ff500000.dwc3: Configuration mismatch. dr_mode forced to host
[ 3.756688@0] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 3.756825@0] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[ 3.765097@0] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f664 hci version 0x100 quirks 0x02010010
[ 3.773482@0] xhci-hcd xhci-hcd.0.auto: irq 22, io mem 0xff500000
[ 3.781053@1] hub 1-0:1.0: USB hub found
[ 3.783409@1] hub 1-0:1.0: 1 port detected
[ 3.788084@1] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 3.793085@1] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[ 3.800982@1] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 3.810465@3] hub 2-0:1.0: USB hub found
[ 3.813094@3] hub 2-0:1.0: config failed, hub doesn't have any ports! (err -19)
[ 3.820355@3] usb usb2: Unsupported the hub
[ 3.825223@3] aml_vrtc rtc: setting system clock to 2024-05-31 13:21:24 UTC (1717161684)
[ 3.833214@3] dwc_otg ff400000.dwc2_a: dwc_otg_driver_probe(ffffffc00d14f000)
[ 3.833291@3] dwc_otg: usb0: type: 2 speed: 0, config: 0, dma: 0, id: 0, phy: ffe09000, ctrl: 0
[ 3.841173@3] dwc_otg ff400000.dwc2_a: base=0xffffff8008580000
[ 3.841185@3] dwc_otg ff400000.dwc2_a: dwc_otg_device=0xffffffc00bb2e200
[ 3.941618@0] dwc_otg: Core Release: 3.10a
[ 3.941716@0] dwc_otg: Setting default values for core params
[ 3.945870@0] dwc_otg: curmode: 0, host_only: 0
[ 3.950369@0] dwc_otg ff400000.dwc2_a: DMA config: BURST_DEFAULT
[ 3.962877@0] dwc_otg: Using Buffer DMA mode
[ 3.962914@0] dwc_otg: OTG VER PARAM: 1, OTG VER FLAG: 1
[ 3.966821@0] dwc_otg: Working on port type = SLAVE
[ 3.971678@0] dwc_otg: Dedicated Tx FIFOs mode
[ 3.978649@0] thermal thermal_zone0: binding zone soc_thermal with cdev thermal-cpufreq-0 failed:-22
[ 3.985403@0] cpucore_cooling_register, max_cpu_core_num:4
[ 3.997541@0] gxbb_pm: enter meson_pm_probe!
[ 3.997597@0] no vddio3v3_en pin
[ 3.999244@0] pm-meson aml_pm: Can't get switch_clk81
[ 4.004359@0] gxbb_pm: meson_pm_probe done
[ 4.009300@0] meson_uart ff803000.serial: ttyS0 use xtal(24M) 24000000 change 115200 to 115200
[ 4.015578@0] Freeing unused kernel memory: 3648K
[ 4.029838@0] meson_uart ff803000.serial: ttyS0 use xtal(24M) 24000000 change 115200 to 115200
[ 4.285121@1] ubi0: attaching mtd5
[ 4.303643@1] ubi0: scanning is finished
[ 4.308208@2] ubi0: attached mtd5 (name "config", size 5 MiB)
[ 4.308340@2] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 4.315412@2] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 4.322306@2] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 4.329420@2] ubi0: good PEBs: 40, bad PEBs: 0, corrupted PEBs: 0
[ 4.335477@2] ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
[ 4.342852@2] ubi0: max/mean erase counter: 7/3, WL threshold: 4096, image sequence number: 3124339084
[ 4.352117@2] ubi0: available PEBs: 0, total reserved PEBs: 40, PEBs reserved for bad PEB handling: 4
[ 4.361338@1] ubi0: background thread "ubi_bgt0d" started, PID 1076
[ 4.374291@0] UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 1080
[ 4.409663@3] UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "config_data"
[ 4.412048@3] UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 4.422142@3] UBIFS (ubi0:0): FS size: 2793472 bytes (2 MiB, 22 LEBs), journal size 1015809 bytes (0 MiB, 6 LEBs)
[ 4.432342@3] UBIFS (ubi0:0): reserved for root: 131942 bytes (128 KiB)
[ 4.438928@3] UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID 66A84733-9E29-4460-9BEC-E21E8E756E24, small LPT model
[ 4.463427@0] ubi2: attaching mtd6
[ 5.136312@2] ubi2: scanning is finished
[ 5.143128@0] ubi2: attached mtd6 (name "nvdata", size 185 MiB)
[ 5.143425@0] ubi2: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 5.150533@0] ubi2: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 5.157403@0] ubi2: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 5.164496@0] ubi2: good PEBs: 1480, bad PEBs: 0, corrupted PEBs: 0
[ 5.170743@0] ubi2: user volume: 1, internal volumes: 1, max. volumes count: 128
[ 5.178103@0] ubi2: max/mean erase counter: 5/2, WL threshold: 4096, image sequence number: 740434435
[ 5.187296@0] ubi2: available PEBs: 0, total reserved PEBs: 1480, PEBs reserved for bad PEB handling: 4
[ 5.196670@2] ubi2: background thread "ubi_bgt2d" started, PID 1088
[ 5.209641@0] UBIFS (ubi2:0): background thread "ubifs_bgt2_0" started, PID 1092
[ 5.243038@1] UBIFS (ubi2:0): UBIFS: mounted UBI device 2, volume 0, name "nvdata_data"
[ 5.245479@1] UBIFS (ubi2:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 5.255500@1] UBIFS (ubi2:0): FS size: 185384960 bytes (176 MiB, 1460 LEBs), journal size 9269248 bytes (8 MiB, 73 LEBs)
[ 5.266322@1] UBIFS (ubi2:0): reserved for root: 4952683 bytes (4836 KiB)
[ 5.273083@1] UBIFS (ubi2:0): media format: w4/r0 (latest is w4/r0), UUID 8E16A460-428F-46AC-A2CF-4D51959C219A, small LPT model
[ 5.499021@3] eth0: device MAC address 02:44:0c:a6:b3:4a
[ 5.581804@3] meson6-dwmac ff3f0000.ethernet eth0: fail to init PTP.
[ 5.583092@3] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 5.834896@3] uart_trans: loading out-of-tree module taints kernel.
[ 5.837440@3] register uart_trans chrdev success.
[ 5.840627@3] meson_uart ff804000.serial: ttyS3 use xtal(24M) 24000000 change 0 to 9600
[ 5.848358@3] tty port open success [/dev/ttyS3]!
[ 5.852989@3] meson_uart ff804000.serial: ttyS3 use xtal(24M) 24000000 change 9600 to 115200
[ 5.861379@3] init sucess for tty struct (246:3) [/dev/ttyS3]
[ 5.867694@3] meson_uart ffd23000.serial: ttyS2 use xtal(24M) 24000000 change 0 to 9600
[ 5.875171@3] tty port open success [/dev/ttyS2]!
[ 5.879860@3] meson_uart ffd23000.serial: ttyS2 use xtal(24M) 24000000 change 9600 to 115200
[ 5.888269@3] init sucess for tty struct (246:2) [/dev/ttyS2]
[ 5.894392@3] meson_uart ffd24000.serial: ttyS1 use xtal(24M) 24000000 change 0 to 9600
[ 5.902021@3] tty port open success [/dev/ttyS1]!
[ 5.906686@3] meson_uart ffd24000.serial: ttyS1 use xtal(24M) 24000000 change 9600 to 115200
[ 5.915106@3] init sucess for tty struct (246:1) [/dev/ttyS1]
[ 5.921374@3] create workqueue success!
[ 7.609045@3] meson6-dwmac ff3f0000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx
[ 7.612328@3] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 28.079669@0] uart trans dev open.
[ 28.079792@0] uart_buf virt addr = 0xffffffc00b180000
[ 28.082752@0] uart_buf phys addr = 0x0b180000
[ 28.086972@0] uart_buf pfn = 0x0000b180
[ 28.091325@0] uart trans stop send work timer.
[ 28.096235@0] uart trans set chain exist bits:0x7.
[ 28.100586@0] uart trans set work queue count 768.
[ 181.155112@2] uart set baud to: 4098
[ 181.155172@2] uart set baud to: 4098
[ 181.156684@2] uart set baud to: 4098
[ 196.557720@1] meson_uart ff804000.serial: ttyS3 use xtal(24M) 24000000 change 115200 to 1000000
[ 196.560806@1] uart set baud to: 4104
[ 196.624837@2] meson_uart ffd23000.serial: ttyS2 use xtal(24M) 24000000 change 115200 to 1000000
[ 196.627976@2] uart set baud to: 4104
[ 196.691909@2] meson_uart ffd24000.serial: ttyS1 use xtal(24M) 24000000 change 115200 to 1000000
[ 196.695139@2] uart set baud to: 4104
[ 212.914543@2] uart trans start send work timer.
[ 663.795003@2] hrtimer: interrupt took 49627 ns
[ 682.237980@2] uart trans stop send work timer.
===========================================Miner log===========================================
2024-05-31 13:21:31 Miner compile time: Tue Apr 9 11:41:45 CST 2024 type: Antminer S19k Pro sn :HQDZAEUBCAABI00LD
2024-05-31 13:21:32 This is fix-freq version
2024-05-31 13:21:32 Miner compile time: Tue Apr 9 11:41:45 CST 2024 type: Antminer S19k Pro
2024-05-31 13:21:32 Miner sn: HQDZAEUBCAABI00LD
2024-05-31 13:21:32 commit version: 02407a8d 2024-04-08 13:24:38, build by: jenkins 2024-04-09 12:13:31
2024-05-31 13:21:32 opt_multi_version = 1
2024-05-31 13:21:32 opt_bitmain_ab = 1
2024-05-31 13:21:32 mid_auto_gen = 1
2024-05-31 13:21:32 opt_bitmain_work_mode = 0
2024-05-31 13:21:32 port 439 already exported
2024-05-31 13:21:32 port 454 already exported
2024-05-31 13:21:32 port 440 already exported
2024-05-31 13:21:32 port 455 already exported
2024-05-31 13:21:32 port 441 already exported
2024-05-31 13:21:32 port 456 already exported
2024-05-31 13:21:32 port 438 already exported
2024-05-31 13:21:32 port 453 already exported
2024-05-31 13:21:32 port 446 already exported
2024-05-31 13:21:32 port 445 already exported
2024-05-31 13:21:32 Note: front fan is power on!
2024-05-31 13:21:32 Note: rear fan is power on!
2024-05-31 13:21:32 start the http log.
2024-05-31 13:21:32 httpListenThread start ret=0
2024-05-31 13:21:32 start listen on 6060 ...
2024-05-31 13:21:32 load machine BHB56902 conf
2024-05-31 13:21:32 machine : BHB56902
2024-05-31 13:21:32 get test_loop_securely_find_asic_num failed
2024-05-31 13:21:32 get high_temp_sub_freq failed,set default high_temp_sub_freq = 10
2024-05-31 13:21:32 get mix boardname[0][BHB56902], name:BHB56902
2024-05-31 13:21:32 bad chain id = 3
2024-05-31 13:21:35 bad chain id = 3
2024-05-31 13:21:37 power off
2024-05-31 13:21:39 ==========================capability start==========================
2024-05-31 13:21:39 board num = 3
2024-05-31 13:21:39 board id = 0, chain num = 1
2024-05-31 13:21:39 chain id = 0
2024-05-31 13:21:39 board id = 1, chain num = 1
2024-05-31 13:21:39 chain id = 1
2024-05-31 13:21:39 board id = 2, chain num = 1
2024-05-31 13:21:39 chain id = 2
2024-05-31 13:21:39 ==========================capability end============================
2024-05-31 13:21:39 chain num = 3
2024-05-31 13:21:42 load chain 0 eeprom data
2024-05-31 13:21:45 load chain 1 eeprom data
2024-05-31 13:21:48 load chain 2 eeprom data
2024-05-31 13:21:48 eeprom load ret:0
2024-05-31 13:21:48 miner:BHB56901,board_name:BHB56902
2024-05-31 13:21:48 miner:BHB56902,board_name:BHB56902
2024-05-31 13:21:48 create thread get_nonce_and_register_thread
2024-05-31 13:21:48 fixed working voltage = 1390
2024-05-31 13:21:48 Chain
2024-05-31 13:21:48 Chain
2024-05-31 13:21:48 Chain [1] PCB Version: 0x0300
2024-05-31 13:21:48 Chain [1] BOM Version: 0x0000
2024-05-31 13:21:48 Chain [2] PCB Version: 0x0300
2024-05-31 13:21:48 Chain [2] BOM Version: 0x0000
2024-05-31 13:21:48 bad chain id = 3
2024-05-31 13:21:48 Fan check passed.
2024-05-31 13:21:48 init fan pid target=55
2024-05-31 13:21:48 max sensor num = 4
2024-05-31 13:21:48 STATUS_INITED: soc init done!
2024-05-31 13:21:48 temperature_monitor_thread start...
2024-05-31 13:21:51 start to init...
2024-05-31 13:21:51 Wait for hashboard cool, please wait, this may take up to 2 minutes...
2024-05-31 13:22:01 Slept 10 seconds, diff = 0.
2024-05-31 13:22:11 Slept 20 seconds, diff = 0.
2024-05-31 13:22:21 Slept 30 seconds, diff = 0.
2024-05-31 13:22:31 Slept 40 seconds, diff = 0.
2024-05-31 13:22:41 Slept 50 seconds, diff = 0.
2024-05-31 13:22:51 Slept 60 seconds, diff = 0.
2024-05-31 13:23:01 Slept 70 seconds, diff = 0.
2024-05-31 13:23:11 Slept 80 seconds, diff = 0.
2024-05-31 13:23:21 Slept 90 seconds, diff = 0.
2024-05-31 13:23:31 Slept 100 seconds, diff = 0.
2024-05-31 13:23:41 Slept 110 seconds, diff = 0.
2024-05-31 13:23:51 Slept 120 seconds, diff = 0.
2024-05-31 13:23:52 start up min temp by 75a = 22, limit -40
2024-05-31 13:23:52 i2c_sim_init start
2024-05-31 13:23:52 init gpio477
2024-05-31 13:23:52 init gpio476
2024-05-31 13:23:52 i2c_sim_init end
2024-05-31 13:23:54 power open power_version = 0x76
2024-05-31 13:23:58 power is Calibrated
2024-05-31 13:23:58 power sn:DGQG329BCAAAF2468
2024-05-31 13:23:58 enable_power_calibration,calibration date:211208.
2024-05-31 13:23:59 power type version: 0x0076
2024-05-31 13:24:01 disable power watchdog: 0x0000
2024-05-31 13:24:12 set_voltage_by_steps to 1300.
2024-05-31 13:24:15 bad chain id = 3
2024-05-31 13:24:15 set_voltage_by_steps to 1500.
2024-05-31 13:24:23 Chain[0]: find 77 asic, times 0
2024-05-31 13:24:25 Chain[1]: find 77 asic, times 0
2024-05-31 13:24:27 Chain[2]: find 77 asic, times 0
2024-05-31 13:24:32 pulse_mode = 1, ccdly_sel = 0, pwth_sel = 4
2024-05-31 13:24:37 fixed frequency is 590
2024-05-31 13:24:37 Bring up temperature is 22
2024-05-31 13:24:37 set uart relay
2024-05-31 13:24:37 set UART baud to 1000000
2024-05-31 13:24:37 create thread check_miner_status_thread
2024-05-31 13:24:37 create thread check_system_work_thread
2024-05-31 13:24:37 create thread debug_freq_thread
2024-05-31 13:24:37 pulse_mode = 1, ccdly_sel = 0, pwth_sel = 4
2024-05-31 13:24:37 start do_core_reset
2024-05-31 13:24:49 end do_core_reset
2024-05-31 13:24:49 noraml inc freq voltage
2024-05-31 13:24:49 set_voltage_by_steps to 1500.
2024-05-31 13:24:53 Version num 65536
2024-05-31 13:24:53 Mask num 0x1fffe000
2024-05-31 13:24:53 opt_multi_version = 65536, interval timeout = 2620657
2024-05-31 13:24:53 freq = 590, percent = 90, hcn = 4442, timeout = 2620657
2024-05-31 13:24:53 (null)
2024-05-31 13:25:04 freq 200 waiting board temp to 35,curr temp 23
2024-05-31 13:25:14 freq 200 waiting board temp to 35,curr temp 24
2024-05-31 13:25:25 freq 200 waiting board temp to 35,curr temp 25
2024-05-31 13:25:35 freq 200 waiting board temp to 35,curr temp 26
2024-05-31 13:25:45 freq 200 waiting board temp to 35,curr temp 27
2024-05-31 13:25:55 freq 200 waiting board temp to 35,curr temp 27
2024-05-31 13:26:05 freq 200 waiting board temp to 35,curr temp 27
2024-05-31 13:26:16 freq 200 waiting board temp to 35,curr temp 28
2024-05-31 13:26:26 freq 200 waiting board temp to 35,curr temp 28
2024-05-31 13:26:36 freq 200 waiting board temp to 35,curr temp 28
2024-05-31 13:26:46 freq 200 waiting board temp to 35,curr temp 28
2024-05-31 13:26:56 freq 200 waiting board temp to 35,curr temp 29
2024-05-31 13:27:22 freq 400 waiting board temp to 35,curr temp 29
2024-05-31 13:27:32 freq 400 waiting board temp to 35,curr temp 30
2024-05-31 13:27:43 freq 400 waiting board temp to 35,curr temp 31
2024-05-31 13:27:53 freq 400 waiting board temp to 35,curr temp 32
2024-05-31 13:28:03 freq 400 waiting board temp to 35,curr temp 33
2024-05-31 13:28:13 freq 400 waiting board temp to 35,curr temp 33
2024-05-31 13:28:23 freq 400 waiting board temp to 35,curr temp 34
2024-05-31 13:28:33 freq 400 waiting board temp to 35,curr temp 34
2024-05-31 13:28:44 freq 400 waiting board temp to 35,curr temp 34
2024-05-31 13:28:54 freq 400 waiting board temp to 35,curr temp 34
2024-05-31 13:29:04 freq 400 waiting board temp to 35,curr temp 34
2024-05-31 13:29:14 freq 400 waiting board temp to 35,curr temp 34
2024-05-31 13:29:37 set_voltage_by_steps to 1480.
2024-05-31 13:29:40 set_voltage_by_steps to 1460.
2024-05-31 13:29:44 set_voltage_by_steps to 1440.
2024-05-31 13:29:47 pulse_mode = 1, ccdly_sel = 0, pwth_sel = 4
2024-05-31 13:29:47 get board temp:34
2024-05-31 13:29:47 waiting board temp come to 35
2024-05-31 13:29:47 waiting board temp to 35,curr temp 34
2024-05-31 13:29:57 waiting board temp to 35,curr temp 34
2024-05-31 13:30:07 waiting board temp to 35,curr temp 34
2024-05-31 13:30:18 waiting board temp to 35,curr temp 34
2024-05-31 13:30:28 waiting board temp to 35,curr temp 34
2024-05-31 13:30:38 waiting board temp to 35,curr temp 34
2024-05-31 13:30:48 waiting board temp to 35,curr temp 34
2024-05-31 13:30:58 waiting board temp to 35,curr temp 34
2024-05-31 13:31:09 waiting board temp to 35,curr temp 34
2024-05-31 13:31:19 waiting board temp to 35,curr temp 34
2024-05-31 13:31:29 waiting board temp to 35,curr temp 34
2024-05-31 13:31:39 waiting board temp to 35,curr temp 34
2024-05-31 13:31:49 get board temp:34
2024-05-31 13:32:06 set voltage to work voltage
2024-05-31 13:32:06 set_voltage_by_steps to 1430.
2024-05-31 13:32:08 set_voltage_by_steps to 1420.
2024-05-31 13:32:10 set_voltage_by_steps to 1410.
2024-05-31 13:32:13 set_voltage_by_steps to 1400.
2024-05-31 13:32:15 set_voltage_by_steps to 1390.
2024-05-31 13:32:17 create thread check_nonce_status_thread
2024-05-31 13:32:17 create thread power_heart_beat_thread
2024-05-31 13:32:17 Init done!
2024-05-31 13:32:17 STATUS_OKAY
2024-05-31 13:32:17 start the cached job
2024-05-31 13:32:17 Version num 1
2024-05-31 13:32:17 Mask num 0x0
2024-05-31 13:32:17 opt_multi_version = 1, interval timeout = 39
2024-05-31 13:32:17 freq = 590, percent = 90, hcn = 4442, timeout = 39
2024-05-31 13:32:17 set_start_time_point total_tv_start_sys=658 total_tv_end_sys=659
2024-05-31 13:32:19 enable power watchdog: 0x0001
2024-05-31 13:32:32 chain[0] bad asic num: 6 6 0
2024-05-31 13:32:32 chain[0] asic[6]
2024-05-31 13:32:33 chain[1] bad asic num: 6 11 0
2024-05-31 13:32:33 chain[1] asic[12]
2024-05-31 13:32:33 chain[2] bad asic num: 6 6 0
2024-05-31 13:32:33 chain[2] asic[5]
2024-05-31 13:32:37 chain[0] bad asic num: 6 6 1
2024-05-31 13:32:37 chain[0] asic[5] [104] 36876-36772
2024-05-31 13:32:38 chain[1] bad asic num: 6 6 1
2024-05-31 13:32:38 chain[1] asic[6]
2024-05-31 13:32:38 chain[2] bad asic num: 6 6 1
2024-05-31 13:32:38 chain[2] asic[5]
2024-05-31 13:32:42 chain[0] bad asic num: 6 6 2
2024-05-31 13:32:42 chain[0] asic[5]
2024-05-31 13:32:42 Sweep error string = N:3.
2024-05-31 13:32:42 ERROR_UNBALANCE: Unbalance happened, waiting!
2024-05-31 13:32:42 stop_mining_waiting: Unbalance happened, waiting!
2024-05-31 13:32:42 uninit_temp_info
2024-05-31 13:32:42 do not read temp anymore...
2024-05-31 13:32:42 cancel thread
2024-05-31 13:32:42 cancel thread
2024-05-31 13:32:42 cancel thread
2024-05-31 13:32:42 ****power off hashboard****
2024-05-31 13:32:42 power off
2024-05-31 13:32:43 temp monitor thread exit
