AntMiner S1 (new model) no status

[j2014]

Hi,

I have 3 antminers I can connect to via a browser. They are all connected to ethernet on the router. The router says nothing connected on ethernet. The ant miner config page shows the Wan with uptime. The fans are running, i read this means they are connected to the internet.

Should I connect using WAN or LAN?

I added mining config to p2pool and added the address and password, saved and applied.

The miner status page permanently showing no status in all three sections. There isn't even a x or o under ASIC status.

I connected to a second ant miner and I get the same.

What am I missing here? :/

Thanks

[ScaryHash]

Can you get to the screen which shows a login into the antminer using root?

Do you have an IP address for each antminer like 192.168.1.XXX and is it on the same address range as your regular router, the 192.168.1.XXX ?

If you have the router set up as 192.168.2.XX, then something on the 192.168.2.XXX range will NOT connect to it automatically.

[ChuckBuck]

Post screen shots of your miner configuration and WAN interface configuration here so we can help you out.  Cross out any sensitive information like workername and password.

[j2014]

Hi, thanks for the help.

Yes my router is on 192.168.1.XXX and the ant miners are also on the 192.168.1.XXX range.

If I change them to be on 192.168.2.XXX will this automatically work?

My config page for the pools has one pool connecting to http://p2pool.org:9332

Side question, how would the setup change if I got wireless antenna for them later?

[ChuckBuck]

What is your complete WAN Interface setup including mask and DNS?

Post here so we can further help you.

[j2014]

Couldn't find upload image option and image url didn't work. Added link to image.

http://postimg.org/image/g8m7xnx7h/

[ChuckBuck]

Your IPv4 Broadcast has to be 192.168.1.255 and your Primary DNS should be set to 8.8.8.8

Save and Apply, give it a minute or 2, then check Miner Status and check your pool website again.

[j2014]

Thanks I added that and and change the default DNS in one of the other ant miners to 8.8.8.8 and both of them show nothing in the status page.

My pool is set to http://p2pool.org:9332, i added the worker name and a pass. Still nothing.

Can they run on the same subnet, e.g. 192.168.1.XXX, the router is on this subnet too.

[cooldgamer]

Probably having trouble connecting to the pool if it's online but not mining.  Have you tried connecting it to one of the big ones just to see if it will work?

[ChuckBuck]

Yes, the Antminers run on the same subnet.

For your mining configuration, try just entering this:

Pool1     p2pool.org:9332
Pool1 worker     Bitcoin address
Password     anything


Save and apply, give it a minute, then check status again.

[j2014]

Tried that and still no status. I opened the ports on the router too, nothing.

[ChuckBuck]

Try changing pool to BTCGuild or Eligius.  Sometimes those smaller pools are iffy.

[j2014]

Finally got it working, the gateway was wrong.

I made, what I hope isn't a hopeless case. I accidentally changed the IPv4 address of one of my miners into the broadcast range when I changed the wrong field. One miner is now on 192.168.1.255.

Can this be fixed? Is there a way to access the miner directly from an ethernet connection to a computer and ssh into the mac address of the machine and launch the config page?

[windpath]

Finally got it working, the gateway was wrong.

I made, what I hope isn't a hopeless case. I accidentally changed the IPv4 address of one of my miners into the broadcast range when I changed the wrong field. One miner is now on 192.168.1.255.

Can this be fixed? Is there a way to access the miner directly from an ethernet connection to a computer and ssh into the mac address of the machine and launch the config page?

You can try

Code:

ssh root@192.168.1.225

But it might be easier to just hit the factory reset button on the controller and start fresh...

[j2014]

aaahhh. Thanks a lot! Found it hiding there.

Thanks for the help everyone.

[ChuckBuck]

Finally got it working, the gateway was wrong.

I made, what I hope isn't a hopeless case. I accidentally changed the IPv4 address of one of my miners into the broadcast range when I changed the wrong field. One miner is now on 192.168.1.255.

Can this be fixed? Is there a way to access the miner directly from an ethernet connection to a computer and ssh into the mac address of the machine and launch the config page?

You can try

Code:

ssh root@192.168.1.225

But it might be easier to just hit the factory reset button on the controller and start fresh...

Try windpath's suggestion, worst case start from scratch with a factory reset:

[j2014]

SSH was denied. reset it and got it set up now. Thanks