syncis
Newbie
Offline
Activity: 16
Merit: 0
|
|
July 14, 2017, 07:12:48 AM |
|
Ok I just got some new information regarding my problem getting "cannot get target temperature, error 15/999"
I tried ethOS and same thing happened there, i guess that rules out any os/graphic drivers issues because my friend have the exact same rig and it worked flawlessly in ethos.
I have swapped the usb risers as well with no success. The only thing i can Think of is my PSU now, when all 6 cards are at 100% Power , around 900 watt, it almost instant. But if i turn it down to 65%, the whole rig takes 650w from wall, it runs without crashing.
I am using molex directly from psu to Power up to 2 usb risers per Cable, instead of doing the sata to molex convertion. My psu is ax1200i. Can I use the corsair link to somehow see if there is any problem with the psu or maybe change something there that could help me?
All these crashing is btw even with stock setting, no oc at all.
What do you guys Think?
|
|
|
|
|
|
|
|
|
You get merit points when someone likes your post enough to give you some. And for every 2 merit points you receive, you can send 1 merit point to someone else!
|
|
|
Advertised sites are not endorsed by the Bitcoin Forum. They may be unsafe, untrustworthy, or illegal in your jurisdiction.
|
|
JustCauseBIH
Member
Offline
Activity: 91
Merit: 10
|
|
July 14, 2017, 08:01:41 AM |
|
@Claymore
Maybe it would be good idea to add some notice in miner when error occur and can be related to overclocking/underclocking.
Just add notice "Check your OC settings and driver version" so we can avoid lot of questions regarding errors that happen in mentioned situations.
|
|
|
|
machupichu
Newbie
Offline
Activity: 12
Merit: 0
|
|
July 14, 2017, 08:15:34 AM |
|
Hi guys,
Im testing dual mining and have some questions.
With ether only mining I have 185Mh/s. With eth + lbry I have 165Mh/s eth and 160Mh/s lbry. Is that ok? Im asking bcuz of this info in first post "with no impact on Ethereum mining speed".
|
|
|
|
wartywarlock
|
|
July 14, 2017, 09:36:28 AM |
|
Hi, I have an occasional niggling issue that seems to have come from 9.7. Every so often the reported hashrate from one of the miners (can be any of them) drops off, like so: http://imgur.com/a/8iXwF mining itself is unaffected, just what is sent to the pool (ethermine.org) 4 rigs has happened on 3 of them at random times. Closing the miner and restarting resolves it, and as said no shares are lost or anything, just annoying because it still means going and checking the rig just in case it is a real dropout. Has anyone else had this, or got a solution? Maybe there is a button to toggle reporting that might kick it back into gear rather than a total restart.
|
|
|
|
Luisjc69
Member
Offline
Activity: 163
Merit: 10
|
|
July 14, 2017, 09:41:41 AM |
|
Hi guys,
wich coin are the best for mining in DUAL mode with ETH?
bcs only ETH is at moment really not the best for mining solo (in Europe!)
LBC, DEC, PASC, SC.....??
Someone have experience??
Thank you very much
Greetings Luisa
|
|
|
|
khufuking
|
|
July 14, 2017, 10:14:32 AM |
|
I am dual mining eth=sia can someone please explain this to me ? why my calculated hash rate is so different ! there is even 1 full hour with 0 calculated hash rate . My monthly income showing results worst than before I oc my mem by a lot . there is 0 error on my miner . why my calculated hash rate is so unstable
|
|
|
|
Saphire
|
|
July 14, 2017, 10:33:06 AM |
|
In Claymore 9.7 "No pools specified!" Why do i get this error when i changed my wallet adress in bat file. Note: I am using Claymore old version wihtout any problem.
|
|
|
|
Luisjc69
Member
Offline
Activity: 163
Merit: 10
|
|
July 14, 2017, 11:05:14 AM |
|
questions....only questions... )
|
|
|
|
uvminer
Newbie
Offline
Activity: 5
Merit: 0
|
|
July 14, 2017, 11:42:58 AM |
|
... AX1200i You have a very decent PSU. Keep in mind, that if the PSU pulls 1000w from the wall this means your rig is pulling arround (1000 * 94% efficiency = ) 940w. Your PSU should be able to deliver 1200w output, so arround 1275w from the wall. I think you are good to go from that perspective. I guess your PSU is faulty or the connections to the GPUs are bad and the voltage drop there is to big. Do you have any PCIe 8 Pin splitters on it? Maybe their Ohm resistance is too big.
|
|
|
|
syncis
Newbie
Offline
Activity: 16
Merit: 0
|
|
July 14, 2017, 11:57:20 AM |
|
... AX1200i You have a very decent PSU. Keep in mind, that if the PSU pulls 1000w from the wall this means your rig is pulling arround (1000 * 94% efficiency = ) 940w. Your PSU should be able to deliver 1200w output, so arround 1275w from the wall. I think you are good to go from that perspective. I guess your PSU is faulty or the connections to the GPUs are bad and the voltage drop there is to big. Do you have any PCIe 8 Pin splitters on it? Maybe their Ohm resistance is too big. No i dont have any splitters, for 6 cards i use 6 pci-e Cables, 4 of them have 1x8 pin and 2 of them have 2x 8 pin.(i leave the other 1x8pin), my cards only takes 1x8pin anyway. I have read alot about my gtx 1070 with micron memory that it will crash sometimes when it goes from idle voltage to full load voltage. Solution was to set "prefer maximum performance" or to lock the voltage above 0.811v for each card. Been running now for 2 hours but really dont have any idea if this is the solution. Anyone else know about this? Connected my 6 risers with molex directly from psu, 2 risers per molex Cable.
|
|
|
|
xxxmattion
Newbie
Offline
Activity: 20
Merit: 0
|
|
July 14, 2017, 12:45:29 PM |
|
when this programer will make an andoid app to allow us monitor our rigs ? also Eth Man when will be able to work through internet ,not only through local lan???
|
|
|
|
Culture
Newbie
Offline
Activity: 19
Merit: 0
|
|
July 14, 2017, 01:08:12 PM |
|
Hi, Claymore, any news about AMD dropping hashrate? annyyyy thanks!
No news for now, but I expect it soon, just need to wait a bit more. How about last night's DAG? It took an average of .3 Mh/s from all 24 of my cards - both RX 480 and RX 580 cards.
|
|
|
|
golden0707
|
|
July 14, 2017, 01:28:57 PM |
|
when this programer will make an andoid app to allow us monitor our rigs ? also Eth Man when will be able to work through internet ,not only through local lan???
Hello! 1. Allready app from Play Market - Claymore\Optiminer Monitor from BCMob 2. You can get static IP from your ISP and watch your rigs from Internet.
|
|
|
|
Saidmod
|
|
July 14, 2017, 02:07:32 PM |
|
Hi, Claymore, any news about AMD dropping hashrate? annyyyy thanks!
No news for now, but I expect it soon, just need to wait a bit more. How about last night's DAG? It took an average of .3 Mh/s from all 24 of my cards - both RX 480 and RX 580 cards. It took even more from my R9 nano.
|
|
|
|
comp
Member
Offline
Activity: 112
Merit: 10
|
|
July 14, 2017, 02:14:55 PM |
|
Hi, Claymore, any news about AMD dropping hashrate? annyyyy thanks!
No news for now, but I expect it soon, just need to wait a bit more. How about last night's DAG? It took an average of .3 Mh/s from all 24 of my cards - both RX 480 and RX 580 cards. Not fixable. Period
|
|
|
|
ZenFr
Legendary
Offline
Activity: 1260
Merit: 1046
|
|
July 14, 2017, 02:16:51 PM |
|
9.7 vs. 9.6 version : my nVidia GTX 1070s are 4% faster (average). Same power usage. Very good :-).
|
|
|
|
altuk
Newbie
Offline
Activity: 1
Merit: 0
|
|
July 14, 2017, 03:11:04 PM |
|
Hi, I have an occasional niggling issue that seems to have come from 9.7. Every so often the reported hashrate from one of the miners (can be any of them) drops off, like so: http://imgur.com/a/8iXwF mining itself is unaffected, just what is sent to the pool (ethermine.org) 4 rigs has happened on 3 of them at random times. Closing the miner and restarting resolves it, and as said no shares are lost or anything, just annoying because it still means going and checking the rig just in case it is a real dropout. Has anyone else had this, or got a solution? Maybe there is a button to toggle reporting that might kick it back into gear rather than a total restart. I have had this issue on one of my rigs with nanopool as well. Restarted and hasn't happen sinced.
|
|
|
|
Nightlander
Newbie
Offline
Activity: 47
Merit: 0
|
|
July 14, 2017, 03:58:41 PM |
|
Still no support for vega? I thought Claymore was working directly with AMD on it.
Claymore has indicated that vega support is a couple weeks away. I have two vega fe's, so I feel you! So do it Looking forward for Vega hashrate ^^ That That and that! Thank you for your early numbers by the way, they helped me make the decision to buy two! I think they stand a really good chance of being awesome. but like most amd releases they well underperform until drivers get sorted and the mod world pulls it apart and works out how to make it run more efficiently and more than likely quite a lot faster. I think the rx500 days are very limited For the price you (could, if they were available) get bunch of rx580's needing only two of them to blow vega fe outta water for both hashrate and power efficiency wise. I don't think it's very awesome to push similar hash rate to gpu that was released half a decade ago with double the power and price.
|
|
|
|
nadrojcote
|
|
July 14, 2017, 04:17:43 PM |
|
The numbers would have to be pretty spectacular to justify the $1000+ price tag of the card. Otherwise ROI will be much too long.
It's so pretty though! I'm hoping they pay for themselves, that would make me satisfied. If they make me enough to build a new computer I'd be thrilled. If none of the above happens, I just have to hope my wife doesn't figure that out! How do you plan on making them pay for themselves? 30MH/s at current DAG will get you about $60 a month. It's only a matter of a few months before it will only be able to generate $20 a month. Why are all these people buying Vega FE? You guys know that were only two weeks away from Vega RX being launched right? You're going to be waiting that long for Claymore to update anyways and Vega RX will probably be half the price. So many people are horrible with finances.
|
|
|
|
|