Claymore's Dual Ethereum AMD+NVIDIA GPU Miner v15.0 (Windows/Linux)

[NavyCuda]

RX Vega 64 Liquid 1560gpu/1100mem@1v gpu core
dualminer 9.8 -dcri 60
55-60 degrees with 3000 rpm

Drop your clocks to 1137.  Same hash rate, much cooler running.

Definetly not the case when dual-mining. Hashrate decreased significantly.
And the voltage stay the same.
Will get power meter and need some advice howto downvolt below 1v to test low-power modes.

I was getting 42.1Mh/s and ~1100Mh/s DCR at 1137cc/1100HBM2.  Until it hard crashes... Which I think is related to the block chain driver and Vega FE.

What was the core voltage with this settings?
Pitty, I had to low memclock to 1080mhz because there were some incorrect ETH shares reported by miner.
Now seems ok ... and no single crash yet ...

Have you tried ETH + SIA and other combinations ?

No I have not.

[1713464793]

1713464793

[1713464793]

1713464793

[SubZer0]

At nanopool i can only choose Pascal or Sia as a second coin to mine no DCR?
Where do you guys find that option, or is it a other website.
Would like to hear more about this wan't to change from ETH+SIA to this.

[greatauror28]

At nanopool i can only choose Pascal or Sia as a second coin to mine no DCR?
Where do you guys find that option, or is it a other website.
Would like to hear more about this wan't to change from ETH+SIA to this.

Nanopool doesn't support deCRED. You'd have to enter a supernova (or similar) address to mine dcr.

I recently shifted from eth+sia into eth+dcr due to the pitiful earnings I'm getting now from siacoin. And besides, DCR keeps rising in value. I can also attest that with the same -dcri settings, you'd get higher hash rate for DCR than SIA and lower power draw too.

6x Rx580 | Claymore 9.8 | Aug11 Blockchain Drivers | 175.5 ETH 3500 DCR | 115W GPU-Z | DCRI 20

[NoHash]

RX Vega 64 Liquid 1560gpu/1100mem@1v gpu core
dualminer 9.8 -dcri 60
55-60 degrees with 3000 rpm

How many Watts at the wall?

I have an air that I am headed down to test
Did you mod the voltage?  If so, what did you use?

Thanks

[rednoW]

RX Vega 64 Liquid 1560gpu/1100mem@1v gpu core
dualminer 9.8 -dcri 60
55-60 degrees with 3000 rpm

How many Watts at the wall?

I have an air that I am headed down to test
Did you mod the voltage?  If so, what did you use?

Thanks

I'll bring my watt-meter tomorrow.
I did lower the voltage with wattman.
And again ... 1100 mem gives non-valid shares sometimes in claymore ... need 1080 to be stable ... or more cooling maybe
I'll try to apply additional fan to blow to the card tomorrow too

[parentino]

Hi,just a noob question,just installed latest Beta-Blockchain-Workloads-Aug23,and miner stop working,it reads both cards and than i get "stoped working" messageeverything was just fine with previous crimson 17.xxx,bat file wasnt changed,rolled back to 17.xx version and everything work fine,rlly wanted to try blockhain driver,using claymore 9.8 version on windows 7,cards are rx 470s,any known issues for this cards and driver,thx?

[Recnoir]

Hi,just a noob question,just installed latest Beta-Blockchain-Workloads-Aug23,and miner stop working,it reads both cards and than i get "stoped working" messageeverything was just fine with previous crimson 17.xxx,bat file wasnt changed,rolled back to 17.xx version and everything work fine,rlly wanted to try blockhain driver,using claymore 9.8 version on windows 7,cards are rx 470s,any known issues for this cards and driver,thx?

Did you apply the atikmdag bios patcher after installing the blockchain driver?

[antiycda]

Hi,just a noob question,just installed latest Beta-Blockchain-Workloads-Aug23,and miner stop working,it reads both cards and than i get "stoped working" messageeverything was just fine with previous crimson 17.xxx,bat file wasnt changed,rolled back to 17.xx version and everything work fine,rlly wanted to try blockhain driver,using claymore 9.8 version on windows 7,cards are rx 470s,any known issues for this cards and driver,thx?

remove the overclock setting in the claymore bat file. using AB to adjust

[manotroll]

suport ipv6 ?

[parentino]

Hi,just a noob question,just installed latest Beta-Blockchain-Workloads-Aug23,and miner stop working,it reads both cards and than i get "stoped working" messageeverything was just fine with previous crimson 17.xxx,bat file wasnt changed,rolled back to 17.xx version and everything work fine,rlly wanted to try blockhain driver,using claymore 9.8 version on windows 7,cards are rx 470s,any known issues for this cards and driver,thx?

Did you apply the atikmdag bios patcher after installing the blockchain driver?

yes,cards are showing properly in device manager

[SummersideGuy]

Eth Difficulty spiked a lot in the last day or so, is that the difficulty bomb? I went from  1.3 eth a month to 0.85 eth a month overnight!!!

[parentino]

Hi,just a noob question,just installed latest Beta-Blockchain-Workloads-Aug23,and miner stop working,it reads both cards and than i get "stoped working" messageeverything was just fine with previous crimson 17.xxx,bat file wasnt changed,rolled back to 17.xx version and everything work fine,rlly wanted to try blockhain driver,using claymore 9.8 version on windows 7,cards are rx 470s,any known issues for this cards and driver,thx?

remove the overclock setting in the claymore bat file. using AB to adjust

no Oc settings,just basic solo mining command

[antiycda]

Hi,just a noob question,just installed latest Beta-Blockchain-Workloads-Aug23,and miner stop working,it reads both cards and than i get "stoped working" messageeverything was just fine with previous crimson 17.xxx,bat file wasnt changed,rolled back to 17.xx version and everything work fine,rlly wanted to try blockhain driver,using claymore 9.8 version on windows 7,cards are rx 470s,any known issues for this cards and driver,thx?

remove the overclock setting in the claymore bat file. using AB to adjust

no Oc settings,just basic solo mining command

did you tried the aug-11

[Odetas]

RX Vega 64 Liquid 1560gpu/1100mem@1v gpu core
dualminer 9.8 -dcri 60
55-60 degrees with 3000 rpm
https://i.imgur.com/vjoKou8.png

Are those decred MH from all of your cards?  That isn't just from the Vega is it?

Does anyone know of a thread that has been tracking which RAM is in which brand GPUs?

[Bleeker]

Hi,

I just switched from win7 to win10 to be able to use the new AMD blockchain drivers among other things. I have a mix of 480/580/570 cards using claymore 9.8. I also use an autoswitching pool. I am experiencing a problem where my 8gb 480 card crashes when switching mining from eth classic (epoch 144) to eth (epoch 140). The other cards do fine during the new DAG generation but the 480 goes down and the miner/OS will lock up shortly thereafter. So far, the switching only occurs when the devfee wants to mine eth. All of the cards are mildly memclocked/uv and have previously been stable for days on win7/17.71/claymore 9.8. I have env variables set and 32 GB pagefile.

Unfortunately, my only solution so far has been to turn off the devfee - which I would rather not do. Any suggestions on how to fix this? Thanks

[KGV]

Hi,

I just switched from win7 to win10 to be able to use the new AMD blockchain drivers among other things. I have a mix of 480/580/570 cards using claymore 9.8. I also use an autoswitching pool. I am experiencing a problem where my 8gb 480 card crashes when switching mining from eth classic (epoch 144) to eth (epoch 140). The other cards do fine during the new DAG generation but the 480 goes down and the miner/OS will lock up shortly thereafter. So far, the switching only occurs when the devfee wants to mine eth. All of the cards are mildly memclocked/uv and have previously been stable for days on win7/17.71/claymore 9.8. I have env variables set and 32 GB pagefile.

Unfortunately, my only solution so far has been to turn off the devfee - which I would rather not do. Any suggestions on how to fix this? Thanks

If you on ethermine.org, change server

[Skol600ml]

RX Vega 64 Liquid 1560gpu/1100mem@1v gpu core
dualminer 9.8 -dcri 60
55-60 degrees with 3000 rpm

Are those decred MH from all of your cards?  That isn't just from the Vega is it?

Does anyone know of a thread that has been tracking which RAM is in which brand GPUs?

That screenshot shows only one card, it's GPU0. Vega is good for the 2nd coin. FE can do 4k alone with high dcri.

[Bleeker]

Hi,

I just switched from win7 to win10 to be able to use the new AMD blockchain drivers among other things. I have a mix of 480/580/570 cards using claymore 9.8. I also use an autoswitching pool. I am experiencing a problem where my 8gb 480 card crashes when switching mining from eth classic (epoch 144) to eth (epoch 140). The other cards do fine during the new DAG generation but the 480 goes down and the miner/OS will lock up shortly thereafter. So far, the switching only occurs when the devfee wants to mine eth. All of the cards are mildly memclocked/uv and have previously been stable for days on win7/17.71/claymore 9.8. I have env variables set and 32 GB pagefile.

Unfortunately, my only solution so far has been to turn off the devfee - which I would rather not do. Any suggestions on how to fix this? Thanks

If you on ethermine.org, change server

Nope, miningpoolhub

[KGV]

Hi,

I just switched from win7 to win10 to be able to use the new AMD blockchain drivers among other things. I have a mix of 480/580/570 cards using claymore 9.8. I also use an autoswitching pool. I am experiencing a problem where my 8gb 480 card crashes when switching mining from eth classic (epoch 144) to eth (epoch 140). The other cards do fine during the new DAG generation but the 480 goes down and the miner/OS will lock up shortly thereafter. So far, the switching only occurs when the devfee wants to mine eth. All of the cards are mildly memclocked/uv and have previously been stable for days on win7/17.71/claymore 9.8. I have env variables set and 32 GB pagefile.

Unfortunately, my only solution so far has been to turn off the devfee - which I would rather not do. Any suggestions on how to fix this? Thanks

If you on ethermine.org, change server

Nope, miningpoolhub

Then try ethermine.org

[bardacuda]

Hi,just a noob question,just installed latest Beta-Blockchain-Workloads-Aug23,and miner stop working,it reads both cards and than i get "stoped working" messageeverything was just fine with previous crimson 17.xxx,bat file wasnt changed,rolled back to 17.xx version and everything work fine,rlly wanted to try blockhain driver,using claymore 9.8 version on windows 7,cards are rx 470s,any known issues for this cards and driver,thx?

Yes, the drivers are known to not work at all on Win7.

Hi,

I just switched from win7 to win10 to be able to use the new AMD blockchain drivers among other things. I have a mix of 480/580/570 cards using claymore 9.8. I also use an autoswitching pool. I am experiencing a problem where my 8gb 480 card crashes when switching mining from eth classic (epoch 144) to eth (epoch 140). The other cards do fine during the new DAG generation but the 480 goes down and the miner/OS will lock up shortly thereafter. So far, the switching only occurs when the devfee wants to mine eth. All of the cards are mildly memclocked/uv and have previously been stable for days on win7/17.71/claymore 9.8. I have env variables set and 32 GB pagefile.

Unfortunately, my only solution so far has been to turn off the devfee - which I would rather not do. Any suggestions on how to fix this? Thanks

Use '-allcoins etc'