lankyman
|
|
October 27, 2017, 11:22:42 PM |
|
At the moment I'm getting 19 and about 280-290 sols on gigabyte windforce oc 3gb hynix memory
Sounds awesome, is this overclocked and stuff?
|
|
|
|
|
|
|
|
Whoever mines the block which ends up containing your transaction will get its fee.
|
|
|
Advertised sites are not endorsed by the Bitcoin Forum. They may be unsafe, untrustworthy, or illegal in your jurisdiction.
|
|
wacko
Legendary
Offline
Activity: 1106
Merit: 1014
|
|
October 28, 2017, 12:28:05 AM |
|
At the moment I'm getting 19 and about 280-290 sols on gigabyte windforce oc 3gb hynix memory
Sounds awesome, is this overclocked and stuff? How is that awesome? Hynix chips are the worst on 1060s. 19 MH/s with Hynix memory is most likely "overclocked and stuff", at usual stock clocks it's ~ 17-18 MH/s. You can easily get 22-23 MH/s with Micron chips and 23-25 MH/s with Samsung chips. Equihash is faster with Samsung and Micron too, it's not as memory dependent as Dagger, but still benefits from faster vram.
|
|
|
|
GordoLui
Jr. Member
Offline
Activity: 73
Merit: 2
|
|
October 28, 2017, 09:06:35 AM |
|
Zotac GTX 1060- 6 cards
Ethereum- 141 mh/s, PL 65%, fan 40%, 535w @wall Equihash- 1720 sol/s, PL 66%, fan 40% 550w @wall XMR- 3100 mh/s, PL 99% fan, 40% 410w @wall
I think these are micron. Haven't really checked. Cant mine stable past, +150 core +685 mem. I was really impressed by how efficient they were at mining XMR. My system idles at 80w, which means the cards were drawing only 330w. 55w for 520mh/s is very nice! 23.5mh/s for eth @75w isnt that bad. Can get it higher to around 24.3mh/s but i think i had to up the PL to 80%. Equihash gives me around 1720 sol/s at 66% which averages out to about 286 mh/s at around 80w a card. These get even more efficient at 50% PL but I think were mining at around the 1500sol/s.
(2)Asus ROG Strix GTX 1060- 6 cards
Equihash-1920 sol/s, PL 65%, fan 45%, 665w @wall.
These are a bit less power efficient but are able to mine equihash at a higher rate than the zotacs. Havent tested ethereum or xmr yet. These were for sure microns, they can go up to +150 core, and around +550+600 mem before they get unstable. I do plan to test them for other algorithms later.
|
|
|
|
|
Oakey22
|
|
October 28, 2017, 11:04:51 AM |
|
What's the typical ROI on these cards? Are they worth getting over then rx480s?
|
|
|
|
Pendra37
Newbie
Offline
Activity: 9
Merit: 0
|
|
October 28, 2017, 01:38:43 PM Last edit: October 29, 2017, 07:46:06 AM by Pendra37 |
|
What's the typical ROI on these cards? Are they worth getting over then rx480s?
A 1060 6gb with Samsung RAM does around 0.125 Eth/month. That is about 32 USD/month after deducting electricity. Non Samsung does around 0.1 Eth/month and probably bring in about 26 USD. I calculate something like ~7 months for 3Gb ~9 months for 6Gb for Samsung, 9-11 months for non Samsung.
|
|
|
|
lezanch
Newbie
Offline
Activity: 25
Merit: 0
|
|
October 29, 2017, 08:16:24 PM |
|
Hi Guys...
some tricks or some else to improve the Nicehash Miner 2.0.1.3 mining profitably? I don't know if I can keep the same settings as per ETH Nanopool mining or if some extra core or memory must be considered. Any Advice?
Thank you
|
|
|
|
FallenFromMoon
Newbie
Offline
Activity: 8
Merit: 0
|
|
October 29, 2017, 09:49:37 PM |
|
Tried to search on different topics and blogs and couldn't find exact results.
So, what is the hashrate of GTX 1060 on different algos? Especially on Ether.
my msi 1060 6gb with hynix memory ~18.3mh/s +100 core +550 memory
|
|
|
|
P4ndoraBox
|
|
October 29, 2017, 11:26:28 PM |
|
Hi Guys...
some tricks or some else to improve the Nicehash Miner 2.0.1.3 mining profitably? I don't know if I can keep the same settings as per ETH Nanopool mining or if some extra core or memory must be considered. Any Advice?
Thank you
Manually mine it in the meantime if there are no answers about it. Maybe a few google searchs will help you.
|
|
|
|
wxxyz
Newbie
Offline
Activity: 44
Merit: 0
|
|
October 30, 2017, 09:59:16 PM |
|
Hi Guys...
some tricks or some else to improve the Nicehash Miner 2.0.1.3 mining profitably? I don't know if I can keep the same settings as per ETH Nanopool mining or if some extra core or memory must be considered. Any Advice?
Thank you
If you increase your core and memory and it increases your hashrate, then it would increase the hashrate on Nicehash too. The only difference is if one pool or the other (or nicehash) has different payment methods, or less down time, etc.
|
|
|
|
mano237
Member
Offline
Activity: 168
Merit: 10
|
|
November 02, 2017, 09:03:49 PM |
|
Is it more profitable to mine btg with a 1060? Someone already tried?
|
|
|
|
matthewtherry
Member
Offline
Activity: 308
Merit: 10
|
|
November 02, 2017, 09:34:50 PM |
|
I can't go up than 20 mhs with 1060. I have tried overclock on windows but max 20 mhs...
|
|
|
|
SafeCash
Newbie
Offline
Activity: 13
Merit: 0
|
|
November 02, 2017, 09:35:36 PM |
|
Is it more profitable to mine btg with a 1060? Someone already tried?
Hashrate on BCG is insane. However, it is an equihash algo. You want to go for low difficulty coins if you want to be extremely profitable.
|
|
|
|
Sandy Lesmana
Newbie
Offline
Activity: 4
Merit: 0
|
|
November 04, 2017, 02:24:36 AM |
|
Zotac GTX 1060 6GB AMP (Micron) 323Sols/s using DSTM 0.5.3 Power Limit 85% Temp Limit 75C (Average 65C on Open Air) Core Clock +175 Mem Clock +650
Zotac GTX 1060 3GB AMP (Hynix) 298Sols/s using DSTM 0.5.3 Power Limit 80% Temp Limit 75C (Average 65C on Open Air) Core Clock +144 Mem Clock +529
|
|
|
|
preda
|
|
November 06, 2017, 08:29:17 AM |
|
1060 3gb
cryptonight = 500 h nicehash
equihash= 280/300 sol (zm 0.5.4)
ethhash= 24.5mh (whatever miner nicehash claymore ethminer)
skunkhush= 18mh
timetravel 10 (spmod2 ccminer)
Lyra2REv2 23mh
keccac 450mh
|
|
|
|
risinqsun
Sr. Member
Offline
Activity: 672
Merit: 273
-
|
|
November 06, 2017, 08:44:00 AM Last edit: November 06, 2017, 09:19:17 AM by risinqsun |
|
Update 25/10/2017 All GTX 1060 Gaming (Micron Mem) Current Settings/Clocks + Hashrate: Core Voltage= * Power Limit = 50 Temp Limit= 85c Core Clock = -130 Memory Clock = +700 Fan Speed = %50 1GPU Dual Mining stats 90/10: ETC: 20.225 MH/s, PASC: 73.750 MH/s I guess not best ! I searching best value
|
|
|
|
bitfools
Member
Offline
Activity: 112
Merit: 12
|
|
November 06, 2017, 09:13:07 AM |
|
Is it more profitable to mine btg with a 1060? Someone already tried?
I have BTG mining SOLO, and on EWBF & CCMINER It's all the same 1060 3 & 6 GB cards about 300 sols/sec ( equihash ) The difficulty right now on testnet is 45,000, its reporting about 5 days for luck When I target a RIG at BTG ( pool.gold or solo ) at +2k sols/sec, my luck goes to 0.3 days, I get paid out in 'testnet' but it never shows up on the bgold-cli "getbalance" or on there 'explorer' because NONE of the BTCGPU software works, its all a pile of shit, a poorly deployed BTC clone, the developers are chinese ASIC guys who don't know C++.
|
|
|
|
preda
|
|
November 06, 2017, 09:23:32 AM |
|
Is it more profitable to mine btg with a 1060? Someone already tried?
I have BTG mining SOLO, and on EWBF & CCMINER It's all the same 1060 3 & 6 GB cards about 300 sols/sec ( equihash ) The difficulty right now on testnet is 45,000, its reporting about 5 days for luck When I target a RIG at BTG ( pool.gold or solo ) at +2k sols/sec, my luck goes to 0.3 days, I get paid out in 'testnet' but it never shows up on the bgold-cli "getbalance" or on there 'explorer' because NONE of the BTCGPU software works, its all a pile of shit, a poorly deployed BTC clone, the developers are chinese ASIC guys who don't know C++. mining bitcoinz(equihash) or bitcore(timetravel 10) is the most profitable now
|
|
|
|
Snub
|
|
November 06, 2017, 10:04:47 AM |
|
on my MSI GTX 1060 GAMING X - 19 mh/s stock and I don't want to overclock it for now)
|
|
|
|
sp_
Legendary
Offline
Activity: 2884
Merit: 1087
Team Black developer
|
|
November 06, 2017, 10:38:47 AM |
|
Cryptonight sp-mod does 600hash on the gtx 1060 with samsung memory
|
|
|
|
|