disman
Newbie
Offline
Activity: 25
Merit: 0
|
|
November 14, 2016, 05:29:26 AM |
|
What do you rejoice? It is advantageous when your speed is higher than the other. And when the rate rises in all, you are in relation to other, standing pat are.
It just kills the coin.
|
|
|
|
|
|
The Bitcoin software, network, and concept is called "Bitcoin" with a capitalized "B". Bitcoin currency units are called "bitcoins" with a lowercase "b" -- this is often abbreviated BTC.
|
|
|
Advertised sites are not endorsed by the Bitcoin Forum. They may be unsafe, untrustworthy, or illegal in your jurisdiction.
|
KougarLOB
Member
Offline
Activity: 136
Merit: 16
|
|
November 14, 2016, 05:31:08 AM |
|
Hi. Many thanks for a job well done! But what happened and how to fix it? in the latest version 5 all my video show 380x - 0 sols. And it is not even loaded completely. Driver tested 16.11.3, 16.9.2 What could be the problem?
update. 480 and 380 do not work if run in a single window If you run two separate windows. it works but writes that long busy and asks you to specify a different port Whether it is possible to fix?
Same problem rig 480/480/470/380x 380x - 0 sol if 380 run single - work fine, but if run 2 miners 1 - 480/480/470 and 2 - 380 drop speed on both miner by 20-30% ( Confirmed here as well across two rigs running AMD 16.11.2 on Windows 10. Mix of 480s and 390s. First rig has two cards and three in the other. Seems to drop the the last card from the group so it drives only 1 of 2 or 2 of 3. Unused card reads idle temperatures. Using "-id 01" or "-id 0,1" (w/w/o comma) makes no difference. Hope this gets cleared up soon. Remarkable speed difference over v4.0 and SilentArmy5 for Windows. I'm content to pay DevFee as this miner continues to improve. Thank you.
|
1ER7JwEjpjQfm4qaTxy6EaNdNy8MqzP1pt
|
|
|
Bananana
|
|
November 14, 2016, 05:49:12 AM |
|
What do you rejoice? It is advantageous when your speed is higher than the other. And when the rate rises in all, you are in relation to other, standing pat are.
It just kills the coin.
If claymore don't increase speed, then private miner is going to profit a lot more. So its only good that if claymore can increase speed same or faster then private miner..
|
|
|
|
BenCodie
Legendary
Offline
Activity: 1638
Merit: 1036
6.25 ---> 3.125
|
|
November 14, 2016, 05:57:59 AM |
|
I had refused to share my modded rom for a Sapphire Nitro OC RX 480 8gb, but have been asked very politely by several people, soooooooo....... http://www.filehosting.org/file/details/618115/Sapphire%20RX480%20NitroOC%20low%20watt%20modded%20vbios.romThis rom should get ~112 Sol/s @55 watts. I don't use Trixx etc, just run it like it is, but of course you can toy with settings if you wish. My goal was highest hashrate at the lowest wattage. If you find it useful, I am not afraid of tips: BTC 1E56WgKJK4kmaVzwxWYg1wY6iPX1GdipDK ZLC t1VAvb4hGh8Tj68TUSpq38859yCFUxHVmwK Do you have anything for the 470 8gb version? Thanks No I don't. Will it work for this card? How much sols/s are you getting with v5.0 with this modded bios you mentioned above?
|
|
|
|
KougarLOB
Member
Offline
Activity: 136
Merit: 16
|
|
November 14, 2016, 06:31:18 AM |
|
"-di detect" did not work on my two-card system. Could not find warmed card. Result is still mining with one of two cards.
|
1ER7JwEjpjQfm4qaTxy6EaNdNy8MqzP1pt
|
|
|
Vicecoin777
Newbie
Offline
Activity: 1
Merit: 0
|
|
November 14, 2016, 06:34:26 AM |
|
Hi. Many thanks for a job well done! But what happened and how to fix it? in the latest version 5 all my video show 380x - 0 sols. And it is not even loaded completely. Driver tested 16.11.3, 16.9.2 What could be the problem?
update. 480 and 380 do not work if run in a single window If you run two separate windows. it works but writes that long busy and asks you to specify a different port Whether it is possible to fix?
Same problem rig 480/480/470/380x 380x - 0 sol if 380 run single - work fine, but if run 2 miners 1 - 480/480/470 and 2 - 380 drop speed on both miner by 20-30% ( Confirmed here as well across two rigs running AMD 16.11.2 on Windows 10. Mix of 480s and 390s. First rig has two cards and three in the other. Seems to drop the the last card from the group so it drives only 1 of 2 or 2 of 3. Unused card reads idle temperatures. Using "-id 01" or "-id 0,1" (w/w/o comma) makes no difference. Hope this gets cleared up soon. Remarkable speed difference over v4.0 and SilentArmy5 for Windows. I'm content to pay DevFee as this miner continues to improve. Thank you. Dude all you have to do is take yours 4xx cards and create an a run bat file for they (start.bat 2) and you will modificate the comands in this way -id 012 (for example if you have the cards in this order 470/470/480) and next is puting -mport 0 ( -id 012 -mport 0 ) and config the standard bat file (start.bat) in this way -id 345 (for example if you have the olds cards in this order 390/390x/390) in this fle you dont need to put the -mport 0 comand... so if you have 6 caeds per rig in this order 480/470/470/390/390x/390.(012345) no matter the order the thing is separate the olds cards from the new ones.. so you going to use 2 windows of claymore yeah!!! That's what i do! rx 470 115-120 S/s r9 380x 85 - 90 S/s
|
|
|
|
denis1995
|
|
November 14, 2016, 06:36:59 AM |
|
Not bad What pool is this?
|
|
|
|
blue-yu
Newbie
Offline
Activity: 58
Merit: 0
|
|
November 14, 2016, 06:37:52 AM |
|
|
|
|
|
RunnerUp
Newbie
Offline
Activity: 14
Merit: 0
|
|
November 14, 2016, 06:46:05 AM Last edit: November 14, 2016, 06:59:00 AM by RunnerUp |
|
I have 2 rigs x6 msi rx480 8gb cards(ellesmere 1303/2000 stock) on win 10, z97 gaming mb and 8gb ram, 1200watt psu.
Rig 1 has a small overclock of 1350/2100 using afterburner, tried the same on rig 2 and one of the GPU's crashed.
I am getting roughly 720-750 on each rig, 120 - 130/s per card. Is there anything else I can do to increase speed? I'm not sure what mod I would need for the cards bios or how to do memory overclock. Any help is much appreciated.(I am happy with these speeds but would like to learn how to push the cards harder)
Also, what does undervolting the cards do? Is that just to lower power consumption or does it help increase speed?
|
|
|
|
KougarLOB
Member
Offline
Activity: 136
Merit: 16
|
|
November 14, 2016, 06:47:32 AM |
|
Hi. Many thanks for a job well done! But what happened and how to fix it? in the latest version 5 all my video show 380x - 0 sols. And it is not even loaded completely. Driver tested 16.11.3, 16.9.2 What could be the problem?
update. 480 and 380 do not work if run in a single window If you run two separate windows. it works but writes that long busy and asks you to specify a different port Whether it is possible to fix?
Same problem rig 480/480/470/380x 380x - 0 sol if 380 run single - work fine, but if run 2 miners 1 - 480/480/470 and 2 - 380 drop speed on both miner by 20-30% ( Confirmed here as well across two rigs running AMD 16.11.2 on Windows 10. Mix of 480s and 390s. First rig has two cards and three in the other. Seems to drop the the last card from the group so it drives only 1 of 2 or 2 of 3. Unused card reads idle temperatures. Using "-id 01" or "-id 0,1" (w/w/o comma) makes no difference. Hope this gets cleared up soon. Remarkable speed difference over v4.0 and SilentArmy5 for Windows. I'm content to pay DevFee as this miner continues to improve. Thank you. Dude all you have to do is take yours 4xx cards and create an a run bat file for they (start.bat 2) and you will modificate the comands in this way -id 012 (for example if you have the cards in this order 470/470/480) and next is puting -mport 0 ( -id 012 -mport 0 ) and config the standard bat file (start.bat) in this way -id 345 (for example if you have the olds cards in this order 390/390x/390) in this fle you dont need to put the -mport 0 comand... so if you have 6 caeds per rig in this order 480/470/470/390/390x/390.(012345) no matter the order the thing is separate the olds cards from the new ones.. so you going to use 2 windows of claymore yeah!!! That's what i do! rx 470 115-120 S/s r9 380x 85 - 90 S/s Separating the cards into a 0 and 1 bat files then adding -mport 0 to one seems to have worked. Thank you. Now to try it on the three card system...
|
1ER7JwEjpjQfm4qaTxy6EaNdNy8MqzP1pt
|
|
|
Tmdz
|
|
November 14, 2016, 06:50:33 AM |
|
Not bad What pool is this? Nicehash I like them especially when the coin is in decline as it is. (You earn btc directly for each share you submit) So you don't spend all day mining it, then by the time you sell on the exchange its worth 25% less.
|
|
|
|
denis1995
|
|
November 14, 2016, 06:58:57 AM |
|
One of my rigs has Catalyst 15.8 on it.
I have tried several video driver removal tools but whenever I install 15.12 it shows up as 15.8 in Afterburner.
Appreciate any help.
Uninstall in control panel then delete all amd files in C:/ AMD. then reboot the pc and install thr dtiver again. I had the same problem few days ago and this eay fix it. I hope that helps you.
|
|
|
|
denis1995
|
|
November 14, 2016, 07:04:56 AM |
|
Not bad What pool is this? Nicehash Is better tham flypool?
|
|
|
|
Claymore (OP)
Donator
Legendary
Offline
Activity: 1610
Merit: 1325
Miners developer
|
|
November 14, 2016, 07:10:26 AM Last edit: November 14, 2016, 07:33:37 AM by Claymore |
|
What do you rejoice? It is advantageous when your speed is higher than the other. And when the rate rises in all, you are in relation to other, standing pat are.
It just kills the coin.
Exactly - the only one actually making money is Claymore xD If you check history, my miner is not x3 faster than others, I just see how fast others miners and release a bit faster version. This time I have to release faster version due to new miner. If people stop this speed racing I'll stop it too, but you know it won't work Also do note my miner is not for NVidia, not for CPU and not for Linux, so if I release miner with x2 speed, network difficult is not going to raise x2 too.
|
|
|
|
|
gregor12
Newbie
Offline
Activity: 52
Merit: 0
|
|
November 14, 2016, 07:21:39 AM |
|
I like them especially when the coin is in decline as it is. (You earn btc directly for each share you submit) So you don't spend all day mining it, then by the time you sell on the exchange its worth 25% less. How do you do that? When I enter btc address in *.bat file it says this address is not supported.
|
|
|
|
devlin
|
|
November 14, 2016, 07:23:37 AM |
|
now big farms with private miners earning much less. I think in backstage is real war. Farms pay developers for private miners and/or to not release public efficient miners.
|
|
|
|
ghostfaceuk
|
|
November 14, 2016, 07:34:22 AM |
|
Not bad What pool is this? Nicehash I like them especially when the coin is in decline as it is. (You earn btc directly for each share you submit) So you don't spend all day mining it, then by the time you sell on the exchange its worth 25% less. How do you do that? When I enter btc address in *.bat file it says this address is not supported. This is my bat file for btc mining at nice hash ZecMiner64.exe -tt 76 -zpool equihash.eu.nicehash.com:3357/#xnsub -zwal wallet adress -zpsw x -allpools 1 -i 2
|
|
|
|
hashgoalPool
|
|
November 14, 2016, 07:36:45 AM |
|
sapphire 280x not mining claymore 5.0??
|
|
|
|
|
|