miropp
|
|
January 05, 2017, 12:31:16 AM |
|
if you are in Europe - how much they write on invoice? (because high VAT...)
30 $ for Case 10 $ for Fan Thanks. What EU customs code (Taric) you use?
|
|
|
|
|
|
|
|
Advertised sites are not endorsed by the Bitcoin Forum. They may be unsafe, untrustworthy, or illegal in your jurisdiction.
|
|
|
ZedZedNova
Sr. Member
Offline
Activity: 475
Merit: 265
Ooh La La, C'est Zoom!
|
|
January 05, 2017, 03:57:55 AM |
|
I'm pretty sure Claymore isn't going to release anything for linux anymore. Perhaps he will, but i don't think so..
I'm running claymore's v9. 3 ZEC miner on linux (ethOS), but can't speak for any of his other miners running on linux. I probably should upgrade since v9.3 is out. I probably should to do a comparo between the latest from optiminer and claymore. Edit: I just upgraded to claymore v9.3 and will check to see what flypool reports as my 24hour hash rate. Currently it reports 141.4 H/s. upgrade from 9.2 to 9.3 produced a yawn. rate is the same at the pool after almost 24 hours.
|
No mining at the moment.
|
|
|
jadefalke
Legendary
Offline
Activity: 1451
Merit: 1014
|
|
January 05, 2017, 11:08:12 AM |
|
if you are in Europe - how much they write on invoice? (because high VAT...)
30 $ for Case 10 $ for Fan Thanks. What EU customs code (Taric) you use? i used nothing DHL showed up on my Door and asked for 37 Euro, i paid them, end of story.
|
|
|
|
philipma1957
Legendary
Offline
Activity: 4074
Merit: 7590
'The right to privacy matters'
|
|
January 05, 2017, 04:19:47 PM |
|
op and I have been kicking around ideas of how to work out a linux for pandaminer distribution.
I may start a separate thread.
|
|
|
|
peoples
Member
Offline
Activity: 82
Merit: 11
|
|
January 05, 2017, 04:47:13 PM |
|
Hm seems like fans are not controlable ? Anyone mastered changing fanspeed on this panda ?
|
|
|
|
Eliovp (OP)
Legendary
Offline
Activity: 1050
Merit: 1293
Huh?
|
|
January 05, 2017, 05:13:07 PM |
|
Hm seems like fans are not controlable ? Anyone mastered changing fanspeed on this panda ?
Nope, they're directly connected to the mainboard. I'm working on a sollution for this as i don't need them to run at 100%
|
|
|
|
|
QuintLeo
Legendary
Offline
Activity: 1498
Merit: 1030
|
|
January 05, 2017, 11:22:50 PM |
|
Hm seems like fans are not controlable ? Anyone mastered changing fanspeed on this panda ?
Nope, they're directly connected to the mainboard. I'm working on a sollution for this as i don't need them to run at 100% Not going to hurt anything if they do, and helps keep things cooler for better longevity. Now, if they were the GHE screamers I could see wanting to slow them down! Have you checked to see if they even have speed control at all (4 wire interface)? A lot of Deltas are 3-wire "tach output no PWM speed control capability only".
|
I'm no longer legendary just in my own mind! Like something I said? Donations gratefully accepted. LYLnTKvLefz9izJFUvEGQEZzSkz34b3N6U (Litecoin) 1GYbjMTPdCuV7dci3iCUiaRrcNuaiQrVYY (Bitcoin)
|
|
|
TheRider
|
|
January 06, 2017, 02:36:56 AM |
|
Hm seems like fans are not controlable ? Anyone mastered changing fanspeed on this panda ?
Nope, they're directly connected to the mainboard. I'm working on a sollution for this as i don't need them to run at 100% Not going to hurt anything if they do, and helps keep things cooler for better longevity. Now, if they were the GHE screamers I could see wanting to slow them down! Have you checked to see if they even have speed control at all (4 wire interface)? A lot of Deltas are 3-wire "tach output no PWM speed control capability only". I vaguely recall Phil or someone else mentioning they were 3 pin wire fans, thus no speed control.
|
|
|
|
philipma1957
Legendary
Offline
Activity: 4074
Merit: 7590
'The right to privacy matters'
|
|
January 06, 2017, 05:25:37 AM Last edit: January 06, 2017, 06:07:47 AM by philipma1957 |
|
Hm seems like fans are not controlable ? Anyone mastered changing fanspeed on this panda ?
Nope, they're directly connected to the mainboard. I'm working on a sollution for this as i don't need them to run at 100% Not going to hurt anything if they do, and helps keep things cooler for better longevity. Now, if they were the GHE screamers I could see wanting to slow them down! Have you checked to see if they even have speed control at all (4 wire interface)? A lot of Deltas are 3-wire "tach output no PWM speed control capability only". I vaguely recall Phil or someone else mentioning they were 3 pin wire fans, thus no speed control. Let me look at photos I,took. 3 pin direct to power board two jacks on the power input. The fans appear to daisy chain four push five pull.
|
|
|
|
felix73
|
|
January 10, 2017, 01:08:42 AM Last edit: January 10, 2017, 02:40:26 AM by felix73 |
|
Hello!
how to enter the BIOS boot pandaminer? that would put the switch on when power on? enter the BIOS pandaminer when you push the start button Hold on delete key
|
|
|
|
theghost1980
Member
Offline
Activity: 67
Merit: 10
Truth is Only one - La verdad es solo Una -
|
|
February 17, 2017, 11:33:28 PM |
|
Some more results. So XMR still at 4amps (880watt) after 15hrs. Picture: Also did a quick testrun on ethereum using the latest available Claymore miner (bad comparison vs Windows as the latest release there is newer and faster, i tested this and it is faster..) I will test with genoil's as well later today. 236Mh while consuming 5.3A (1166watt) most consumption i've seen as of now.. Picture: Did a testrun for zcash as well. 1730H while consuming 4.9A (1078watt)Picture: Then i did some minor modifcations (rom wise) Improved hashrate and same consumption. So still 4A (880 watt) but this time hitting 6400h Picture: Again, overall, i must say, awesome machine. This could be seriously interesting for bigger farms. I made it so that i just plug in the power, it boots and starts mining. Other algo, no problem. Switch and go. Greetings! Hi there. Thank you so much for your posts, that's very good info. may I ask, how is working the system so far? It's been a couple of months since you got it right? Basically let me know what do you think, is very stable? is worth for buying? Besides XMR / ETH/ ZAC, is there any other cripto you've been able to mine as well? Thanks in advance for your info!
|
Tip me. DASH Xne9JXZhbL9u38xfr6aDtTGogZMZFBbpRN
|
|
|
megax05
Newbie
Offline
Activity: 13
Merit: 0
|
|
February 18, 2017, 05:13:45 AM |
|
@Eliovp can you provide a copy of the bios on those GPUs I see they use Hynix memory and I am interested on the timing on those.
|
|
|
|
dagarair
|
|
February 18, 2017, 12:15:08 PM |
|
Some more results. So XMR still at 4amps (880watt) after 15hrs. Picture: Also did a quick testrun on ethereum using the latest available Claymore miner (bad comparison vs Windows as the latest release there is newer and faster, i tested this and it is faster..) I will test with genoil's as well later today. 236Mh while consuming 5.3A (1166watt) most consumption i've seen as of now.. Picture: Did a testrun for zcash as well. 1730H while consuming 4.9A (1078watt)Picture: Then i did some minor modifcations (rom wise) Improved hashrate and same consumption. So still 4A (880 watt) but this time hitting 6400h Picture: Again, overall, i must say, awesome machine. This could be seriously interesting for bigger farms. I made it so that i just plug in the power, it boots and starts mining. Other algo, no problem. Switch and go. Greetings! Hi there. Thank you so much for your posts, that's very good info. may I ask, how is working the system so far? It's been a couple of months since you got it right? Basically let me know what do you think, is very stable? is worth for buying? Besides XMR / ETH/ ZAC, is there any other cripto you've been able to mine as well? Thanks in advance for your info! Running like a champ. I have a few pandas and run XMR. I am about 6400 (800 a card ish) and sub 900 watts. I also had him write me one for my RX 6 card rigs and I am getting 4.5K on 640 watts!
|
|
|
|
dagarair
|
|
February 18, 2017, 12:15:42 PM |
|
@Eliovp can you provide a copy of the bios on those GPUs I see they use Hynix memory and I am interested on the timing on those.
Yeah he'll provide a copy once you buy it. lol
|
|
|
|
viramarket
|
|
October 31, 2017, 05:32:52 PM |
|
Is in this chat people who use the program Simplemining on Panda the miner B3+ ?
|
|
|
|
dagarair
|
|
October 31, 2017, 09:09:13 PM |
|
it will work on simple mining no problem
|
|
|
|
|