Cointerra Terraminer IV CTA 1 ALIVE but not hashing

[semfreak]

Help! =)

I have 5 Cointerra Terraminer IV's and a few are all doing the same thing. Hashing at 1/2 of what they are supposed to. some CTA 0 and CTA 1 nre between 300 - 400  GH/s. 2 are hashing at full capacity on CTA 0 but CTA 1 just sits there. I am at a loss on what to do.

CTA1 Metrics   High   Low   Avg
Core Temp 1 (°C)   33.91   30.3   31.75
Core Temp 2 (°C)   36.88   30.79   33.50
Ambient Temp (°C)   37.5   36.75   37.12
Fan Speed (RPM)   1,728   1,671   1,700
Pump Speed (RPM)   0   0   0


in the logs I see it restart but never take any shares:
                    
 [2015-04-22 22:34:21] CTA 1: MSG: Reset complete 255
(5s):197.7G (1m):27.92G (5m):5.898G (15m):1.985G (avg):164.2Gh/s          
 [2015-04-22 22:34:23] CTA 0: MSG: Reset complete 255                    
 [2015-04-22 22:34:23] Accepted 01ea5cc4 Diff 134/64 CTA 0                    
 [2015-04-22 22:34:23] Accepted 0327259e Diff 81/64 CTA 0                    
 [2015-04-22 22:34:24] Accepted 0302c56b Diff 85/64 CTA 0                    
 [2015-04-22 22:34:24] Accepted 02058fa0 Diff 127/64 CTA 0                    
 [2015-04-22 22:34:24] Accepted 01490cc6 Diff 199/64 CTA 0                    
 [2015-04-22 22:34:24] Accepted 01c6361a Diff 144/64 CTA 0                    
 [2015-04-22 22:34:26] Accepted 024db374 Diff 111/64 CTA 0                    
 [2015-04-22 22:34:26] Accepted 03880aed Diff 72/64 CTA 0                    
 [2015-04-22 22:34:27] Accepted 02011006 Diff 128/64 CTA 0                    
 [2015-04-22 22:34:27] Accepted 35dcf2a5 Diff 1.22K/64 CTA 0                    
(5s):440.9G (1m):71.74G (5m):15.34G (15m):5.171G (avg):298.8Gh/s


Any ideas? If I was hacked the temps would be high and it would be running. but the temps are low telling me that the issue is not that it is hacked rather CTA 1 just is not working, but why?


Thank you for any help,

-J

[1713582353]

1713582353

[1713582353]

1713582353

[1713582353]

1713582353

[1713582353]

1713582353

[1713582353]

1713582353

[samahan]

I am having the exact same issue. Did you ever figure out a solution?

[-ck]

I am having the exact same issue. Did you ever figure out a solution?

These devices had a very high failure rate with time and considering you're responding to a post that is almost 2 years old, I would say the answer is no. Mine died completely within a few months.

[fanatic26]

A common problem with these boards was the PCB warping from heat and cracking the runs internally on the board. Another thing to try is to unhook the cable running from the psu breakout board to the hashing board. It was a well known issue with some of the boards that they would not hash properly if the breakout board was supplying bad information. Also in the status page you can check the voltage going to each chip. I would verify there are no damaged chips as that would cause slow/no hashing issues.