|
parker423
|
 |
August 22, 2017, 02:33:08 PM |
|
Whats the hashrate for Bitconnect?
|
|
|
|
|
|
|
|
|
|
|
|
|
|
"With e-currency based on cryptographic proof, without the need to
trust a third party middleman, money can be secure and transactions
effortless." -- Satoshi
|
|
|
Advertised sites are not endorsed by the Bitcoin Forum. They may be unsafe, untrustworthy, or illegal in your jurisdiction.
|
|
|
|
|
|
|
|
kurbeks
|
|
August 22, 2017, 03:01:07 PM |
|
Whats the hashrate for Bitconnect?
Posted links in previous page, see them. |
|
|
|
|
shoaib39
Member
 Offline
Activity: 136
Merit: 10
|
|
August 22, 2017, 05:11:14 PM |
|
hello,After electricity gone and come again My L3+ only One 1st hashing board Temper showing 0, and all others board temperature was wrong, After 5 to 10 minutes when i power onn the miner again after switch off Its working normally what will be the problem PSU, Miner, or Power Cable.
|
|
|
|
|
Albortz
Sr. Member
Offline
Activity: 420
Merit: 250
Tax Attorney - Investor - Entrepreneur
|
|
August 22, 2017, 05:18:55 PM |
|
hello,After electricity gone and come again My L3+ only One 1st hashing board Temper showing 0, and all others board temperature was wrong, After 5 to 10 minutes when i power onn the miner again after switch off Its working normally what will be the problem PSU, Miner, or Power Cable.
If i understood it correctly the power went missing? If that is the case it basically fries itself rebooting. Just power it off wait some minutes and power it on again this will assure your miner is rebooting correctly. But why that happened I can't tell you. Did you have lightning struck the house or was it just the miner? |
|
|
|
shoaib39
Member
Offline
Activity: 136
Merit: 10
|
|
August 22, 2017, 05:58:33 PM
Last edit: August 22, 2017, 06:13:41 PM by shoaib39 |
|
hello,After electricity gone and come again My L3+ only One 1st hashing board Temper showing 0, and all others board temperature was wrong, After 5 to 10 minutes when i power onn the miner again after switch off Its working normally what will be the problem PSU, Miner, or Power Cable.
If i understood it correctly the power went missing? If that is the case it basically fries itself rebooting. Just power it off wait some minutes and power it on again this will assure your miner is rebooting correctly. But why that happened I can't tell you. Did you have lightning struck the house or was it just the miner? ya I was running on inverter Its works properly, but electricity gone then its off and starts within second, now from 2 days i run L3+ on Inverter, then i got this problem. But after 5 to 10 minutes onn the miner its work proper. Everything works fine but is see "x" now between oooooooo oooooooo oooooooo oooxoooo oooooooo oooooooo oooooooo oooooooo oooooooo on 1st hashing board. Screenshot:  |
|
|
|
|
|
kurbeks
|
|
August 22, 2017, 06:10:42 PM |
|
You can msg Bitmain. But i doubt it's worth returning board with only one dead chip. Although sooner or later they will start to die on that board.
|
|
|
|
|
shoaib39
Member
Offline
Activity: 136
Merit: 10
|
|
August 22, 2017, 06:27:06 PM
Last edit: August 22, 2017, 06:46:16 PM by shoaib39 |
|
You can msg Bitmain. But i doubt it's worth returning board with only one dead chip. Although sooner or later they will start to die on that board.
If there was problem in Hashing Board, then it will not fine after restart, But now i restart There was no "x" 000x000 between 0, And i think it was PSU problem, Sometimes that only one hashing board not getting power, After sometime everything works fine. If i restart everything fine no "x" between 00000, but after 5 to 10 minutes its "x" came again,but hashing is proper. anyone know what will be the problem. I found something here about this problem. https://enforum.bitmain.com/bbs/topics/3591 |
|
|
|
|
Albortz
Sr. Member
Offline
Activity: 420
Merit: 250
Tax Attorney - Investor - Entrepreneur
|
|
August 22, 2017, 07:11:05 PM |
|
hello,After electricity gone and come again My L3+ only One 1st hashing board Temper showing 0, and all others board temperature was wrong, After 5 to 10 minutes when i power onn the miner again after switch off Its working normally what will be the problem PSU, Miner, or Power Cable.
If i understood it correctly the power went missing? If that is the case it basically fries itself rebooting. Just power it off wait some minutes and power it on again this will assure your miner is rebooting correctly. But why that happened I can't tell you. Did you have lightning struck the house or was it just the miner? ya I was running on inverter Its works properly, but electricity gone then its off and starts within second, now from 2 days i run L3+ on Inverter, then i got this problem. But after 5 to 10 minutes onn the miner its work proper. Everything works fine but is see "x" now between oooooooo oooooooo oooooooo oooxoooo oooooooo oooooooo oooooooo oooooooo oooooooo on 1st hashing board. Screenshot: It might be that one chip burned. But you still got 72 basics show. As far as i remember they get reduced once chips start burning. Then it would be 71 now... Strange. But as long as your hashing power does not drop i would not worry to much about it. |
|
|
|
shoaib39
Member
Offline
Activity: 136
Merit: 10
|
|
August 22, 2017, 07:47:37 PM |
|
hello,After electricity gone and come again My L3+ only One 1st hashing board Temper showing 0, and all others board temperature was wrong, After 5 to 10 minutes when i power onn the miner again after switch off Its working normally what will be the problem PSU, Miner, or Power Cable.
If i understood it correctly the power went missing? If that is the case it basically fries itself rebooting. Just power it off wait some minutes and power it on again this will assure your miner is rebooting correctly. But why that happened I can't tell you. Did you have lightning struck the house or was it just the miner? ya I was running on inverter Its works properly, but electricity gone then its off and starts within second, now from 2 days i run L3+ on Inverter, then i got this problem. But after 5 to 10 minutes onn the miner its work proper. Everything works fine but is see "x" now between oooooooo oooooooo oooooooo oooxoooo oooooooo oooooooo oooooooo oooooooo oooooooo on 1st hashing board. Screenshot: It might be that one chip burned. But you still got 72 basics show. As far as i remember they get reduced once chips start burning. Then it would be 71 now... Strange. But as long as your hashing power does not drop i would not worry to much about it. Bro but after power onn to the miner is was 0 zero everything,there is no "x" But after 5 to 10 minutes its come 1 "x" only,May be, this is PSU problem, What you say? |
|
|
|
|
|
kurbeks
|
|
August 22, 2017, 08:50:24 PM |
|
Most likely that one chip can't cope with set frequency so it get's shut down.
|
|
|
|
|
shoaib39
Member
Offline
Activity: 136
Merit: 10
|
|
August 22, 2017, 10:58:51 PM |
|
Most likely that one chip can't cope with set frequency so it get's shut down.
Sometimes i was getting temperature Zero 0 of 1st hashing board and Other Temperatures wrong. Sometimes everything goes perfect after Restart, And everything works perfectly, but on 1st board ASIC status having only one "x" between This example: ooooo ooooo oooxooo oooooo oooo oooo. See my previous post there was an screenshot of my Antminer Status. |
|
|
|
|
Albortz
Sr. Member
Offline
Activity: 420
Merit: 250
Tax Attorney - Investor - Entrepreneur
|
|
August 22, 2017, 11:07:53 PM |
|
Most likely that one chip can't cope with set frequency so it get's shut down.
Sometimes i was getting temperature Zero 0 of 1st hashing board and Other Temperatures wrong. Sometimes everything goes perfect after Restart, And everything works perfectly, but on 1st board ASIC status having only one "x" between This example: ooooo ooooo oooxooo oooooo oooo oooo. See my previous post there was an screenshot of my Antminer Status. Like said, it happens. As long as your miner is running right now and got only 1 X don't stress it. Just make sure that your power stays consistent. What PSU are you using? If its from bitmain you should not worry. Check all cords and adapters and that is about it what you can do |
|
|
|
|
GMPoison
|
|
August 23, 2017, 12:37:15 AM |
|
Most likely that one chip can't cope with set frequency so it get's shut down.
Sometimes i was getting temperature Zero 0 of 1st hashing board and Other Temperatures wrong. Sometimes everything goes perfect after Restart, And everything works perfectly, but on 1st board ASIC status having only one "x" between This example: ooooo ooooo oooxooo oooooo oooo oooo. See my previous post there was an screenshot of my Antminer Status. Like said, it happens. As long as your miner is running right now and got only 1 X don't stress it. Just make sure that your power stays consistent. What PSU are you using? If its from bitmain you should not worry. Check all cords and adapters and that is about it what you can do Yeah, looks like it is still hashing for 503.5 MH/s, definitely not worth attempting to fix it for what it would cost in lost profits, unless you think whatever happened to the one chip could start happening to the other ones somehow. |
|
|
|
|
wheelz1200
Legendary
Offline
Activity: 3598
Merit: 1406
|
|
August 23, 2017, 01:12:34 AM |
|
Most likely that one chip can't cope with set frequency so it get's shut down.
Sometimes i was getting temperature Zero 0 of 1st hashing board and Other Temperatures wrong. Sometimes everything goes perfect after Restart, And everything works perfectly, but on 1st board ASIC status having only one "x" between This example: ooooo ooooo oooxooo oooooo oooo oooo. See my previous post there was an screenshot of my Antminer Status. Like said, it happens. As long as your miner is running right now and got only 1 X don't stress it. Just make sure that your power stays consistent. What PSU are you using? If its from bitmain you should not worry. Check all cords and adapters and that is about it what you can do Yeah, looks like it is still hashing for 503.5 MH/s, definitely not worth attempting to fix it for what it would cost in lost profits, unless you think whatever happened to the one chip could start happening to the other ones somehow. I would just count your lucky stars. Make sure that everything is fitted (should be with all the others working) and let it stay ripping... |
|
|
|
|
lentyna
|
|
August 23, 2017, 03:29:27 AM |
|
Do any of you guys use 220/240 V power in US with APW3++? What kind of plug and outlet are you using?
|
|
|
|
|
lestherat
Legendary
Offline
Activity: 986
Merit: 1001
|
|
August 23, 2017, 04:26:15 AM |
|
anyone know how to name miners for the nicehash dashboard? I go into the "my workers" tab but cannot diffrentiate which stat is related to each miner... would be good to name them individually and have them recognised in nicehash.
In the antminer panel go to Miner Configuration and rename the worker with your btc address and then write .nameofyourworker1 .nameofyourworker2 .nameofyourworker3 ... without spaces dont forget the dot " . " use the name what you want for each one of your miners. |
|
|
|
|
shoaib39
Member
Offline
Activity: 136
Merit: 10
|
|
August 23, 2017, 05:43:49 AM |
|
Most likely that one chip can't cope with set frequency so it get's shut down.
Sometimes i was getting temperature Zero 0 of 1st hashing board and Other Temperatures wrong. Sometimes everything goes perfect after Restart, And everything works perfectly, but on 1st board ASIC status having only one "x" between This example: ooooo ooooo oooxooo oooooo oooo oooo. See my previous post there was an screenshot of my Antminer Status. Like said, it happens. As long as your miner is running right now and got only 1 X don't stress it. Just make sure that your power stays consistent. What PSU are you using? If its from bitmain you should not worry. Check all cords and adapters and that is about it what you can do Yeah, looks like it is still hashing for 503.5 MH/s, definitely not worth attempting to fix it for what it would cost in lost profits, unless you think whatever happened to the one chip could start happening to the other ones somehow. I would just count your lucky stars. Make sure that everything is fitted (should be with all the others working) and let it stay ripping... I using Bitmain PSU 1600w, What you say guys it will be PSU problem, Because now after every 3 to 4 hours my miner getting restart. But after restart i cant find any problem after 5 to 10 minutes i see one "x" on 1st ASIC board status. |
|
|
|
|
|
GMPoison
|
|
August 23, 2017, 05:49:27 AM |
|
Most likely that one chip can't cope with set frequency so it get's shut down.
Sometimes i was getting temperature Zero 0 of 1st hashing board and Other Temperatures wrong. Sometimes everything goes perfect after Restart, And everything works perfectly, but on 1st board ASIC status having only one "x" between This example: ooooo ooooo oooxooo oooooo oooo oooo. See my previous post there was an screenshot of my Antminer Status. Like said, it happens. As long as your miner is running right now and got only 1 X don't stress it. Just make sure that your power stays consistent. What PSU are you using? If its from bitmain you should not worry. Check all cords and adapters and that is about it what you can do Yeah, looks like it is still hashing for 503.5 MH/s, definitely not worth attempting to fix it for what it would cost in lost profits, unless you think whatever happened to the one chip could start happening to the other ones somehow. I would just count your lucky stars. Make sure that everything is fitted (should be with all the others working) and let it stay ripping... I using Bitmain PSU 1600w, What you say guys it will be PSU problem, Because now after every 3 to 4 hours my miner getting restart. But after restart i cant find any problem after 5 to 10 minutes i see one "x" on 1st ASIC board status. That's weird, I've never had a miner restart every 3 - 4 hours over and over. Are they overheating? If they were, you would think that they would shut down before 3-4 hours and wouldn't take that long to overheat... |
|
|
|
|
shoaib39
Member
Offline
Activity: 136
Merit: 10
|
|
August 23, 2017, 05:53:03 AM |
|
Most likely that one chip can't cope with set frequency so it get's shut down.
Sometimes i was getting temperature Zero 0 of 1st hashing board and Other Temperatures wrong. Sometimes everything goes perfect after Restart, And everything works perfectly, but on 1st board ASIC status having only one "x" between This example: ooooo ooooo oooxooo oooooo oooo oooo. See my previous post there was an screenshot of my Antminer Status. Like said, it happens. As long as your miner is running right now and got only 1 X don't stress it. Just make sure that your power stays consistent. What PSU are you using? If its from bitmain you should not worry. Check all cords and adapters and that is about it what you can do Yeah, looks like it is still hashing for 503.5 MH/s, definitely not worth attempting to fix it for what it would cost in lost profits, unless you think whatever happened to the one chip could start happening to the other ones somehow. I would just count your lucky stars. Make sure that everything is fitted (should be with all the others working) and let it stay ripping... I using Bitmain PSU 1600w, What you say guys it will be PSU problem, Because now after every 3 to 4 hours my miner getting restart. But after restart i cant find any problem after 5 to 10 minutes i see one "x" on 1st ASIC board status. That's weird, I've never had a miner restart every 3 - 4 hours over and over. Are they overheating? If they were, you would think that they would shut down before 3-4 hours and wouldn't take that long to overheat... No there is no over heating, temperature is normal, from 15 days there is no problem This temperature, But problem arises after running this miner on Inverter. |
|
|
|
|
|
GMPoison
|
|
August 23, 2017, 06:32:06 AM |
|
Does anyone have a guess as to when the next batch of L3+ and S9 will be released?
The last batch released was their first October batch and that was three weeks ago.
|
|
|
|
|
|
