ASICMINER Auction: 50 Block Erupter Blades CHECK OP FOR PAYMENT

[lenny_]

Caesium, can you please share your script to format output data from blades?

[Caesium]

Replied in PM. It's just a bit of very ugly Ruby, but if anyone else is interested,

http://telon.net/asic_status.rb.txt

I have local DNS entries that make my asics reachable at asic1/2/3/4, if you don't you may need to replace with an IP where necessary. Sorry it's so ugly and basic, it was only a 5 minute hack to get information into a Terminal I can watch

[dogie]

Replied in PM. It's just a bit of very ugly Ruby, but if anyone else is interested,

http://telon.net/asic_status.rb.txt

I have local DNS entries that make my asics reachable at asic1/2/3/4, if you don't you may need to replace with an IP where necessary. Sorry it's so ugly and basic, it was only a 5 minute hack to get information into a Terminal I can watch

Investigate the position of the proxy rather than the platform. Another user had problems going through a switch to the blades, rather than straight to the router. but the fact its changed at ALL, suggests there is room for improvement.

[Caesium]

Well, I just left it to settle for a bit..

1: 12928 MH/s  271456/ 275231 176.65/min 98.62% 0s up 025h 36:41
2: 12966 MH/s  272246/ 275240 177.18/min 98.91% 0s up 025h 36:33
3: 12899 MH/s  249589/ 253824 176.26/min 98.33% 5s up 023h 36:01
4: 12945 MH/s   11683/  11808 176.92/min 98.94% 0s up 001h 06:02


I think there's quite a lot of factors at play to be honest:
a) latency of my Internet connection as it actually submits shares
b) blocks found lead to a drop, because these units don't do LP
c) pool load
d) stratum proxy (and PC its running on) load
e) local network layout as you say, but can't do much about that, I need to use a switch or I haven't got enough ports :p

They're all around 177 shares/min which isn't catastrophic at the end of the day.

[dogie]

Well, I just left it to settle for a bit..

1: 12928 MH/s  271456/ 275231 176.65/min 98.62% 0s up 025h 36:41
2: 12966 MH/s  272246/ 275240 177.18/min 98.91% 0s up 025h 36:33
3: 12899 MH/s  249589/ 253824 176.26/min 98.33% 5s up 023h 36:01
4: 12945 MH/s   11683/  11808 176.92/min 98.94% 0s up 001h 06:02


I think there's quite a lot of factors at play to be honest:
a) latency of my Internet connection as it actually submits shares
b) blocks found lead to a drop, because these units don't do LP
c) pool load
d) stratum proxy (and PC its running on) load
e) local network layout as you say, but can't do much about that, I need to use a switch or I haven't got enough ports :p

They're all around 177 shares/min which isn't catastrophic at the end of the day.

Ah well. Yours are clearly broken so you might as well give them to me

[Caesium]

Just to confirm, you see a solid 178.00 shares/minute always? I have never seen that ever, but I think mostly its because of stales pulling down the accepted efficiency.

Could you paste one of your outputs from the webpage?

[lenny_]

That's my stats:

Code:

Total MHS:	13149
Received:	0000139705
Accepted:	0000139687
Per Minute:	179.17
Efficiency:	099.98%
Up Time:	0d,12h,59m,36s

Code:

Total MHS:	13030
Received:	0000139723
Accepted:	0000138821
Per Minute:	178.07
Efficiency:	099.35%
Up Time:	0d,12h,59m,33s

[dogie]

Just to confirm, you see a solid 178.00 shares/minute always? I have never seen that ever, but I think mostly its because of stales pulling down the accepted efficiency.

Could you paste one of your outputs from the webpage?

Total MHS:   13046
Received:   0000091550
Accepted:   0000091170
Per Minute:   178.29
Efficiency:   099.58%
Up Time:   0d,08h,31m,21s

Total MHS:   13022
Received:   0000091634
Accepted:   0000091080
Per Minute:   177.94
Efficiency:   099.39%
Up Time:   0d,08h,31m,50s

Damn lenny, that 99.98 is sexual. For some reason I haven't seen either blade go over 24 hours. It either says its restarted, or it is actually restarting roughly once a day. Not got the new cooling on yet, but its hardly hot and its typically restarting at cool times of the day/night.

[Caesium]

You both have nicer stats than me, not sure what I'm doing wrong. Do you use -rt to the stratum proxy? I'm trying one without that flag as a test..

[WinTame2012]

Guys,
What's the best pool (in terms of efficiency) for Erupter Blades so far?

[drlatino999]

Guys,
What's the best pool (in terms of efficiency) for Erupter Blades so far?

I've pulled 97/98% for bitminter and Slush. Others are at 98/99% with slush.

[dogie]

Guys,
What's the best pool (in terms of efficiency) for Erupter Blades so far?

Slush using stratum proxy, although if you work out how to set it up for others I don't see why it wouldn't be any other pool.

[WinTame2012]

Guys,
What's the best pool (in terms of efficiency) for Erupter Blades so far?

I've pulled 97/98% for bitminter and Slush. Others are at 98/99% with slush.

Thanks. That's with the Stratum proxy, right?

[WinTame2012]

Guys,
What's the best pool (in terms of efficiency) for Erupter Blades so far?

Slush using stratum proxy, although if you work out how to set it up for others I don't see why it wouldn't be any other pool.

Thanks for the answer. I'm asking primarily 'cause the stratum proxy itself could have different efficiency with random pools.
Care to share your stratum proxy command line options?

[drlatino999]

Guys,
What's the best pool (in terms of efficiency) for Erupter Blades so far?

Slush using stratum proxy, although if you work out how to set it up for others I don't see why it wouldn't be any other pool.

Thanks for the answer. I'm asking primarily 'cause the stratum proxy itself could have different efficiency with random pools.
Care to share your stratum proxy command line options?

Slush - ./mining_proxy.py -q
Bitminter - /mining_proxy.py -q -o mint.bitminter.com -p 3333 -sh localhost

[WinTame2012]

Guys,
What's the best pool (in terms of efficiency) for Erupter Blades so far?

Slush using stratum proxy, although if you work out how to set it up for others I don't see why it wouldn't be any other pool.

Thanks for the answer. I'm asking primarily 'cause the stratum proxy itself could have different efficiency with random pools.
Care to share your stratum proxy command line options?

Slush - ./mining_proxy.py -q
Bitminter - /mining_proxy.py -q -o mint.bitminter.com -p 3333 -sh localhost

Appreciated. Does -rt affect your mining efficiency?

[dogie]

Interestingly I see 12.2 on both of my blades on slush, but 13.0 on the config. Does that mean I'm losing $$$ somewhere?

[Noitev]

Interestingly I see 12.2 on both of my blades on slush, but 13.0 on the config. Does that mean I'm losing $$$ somewhere?

no, it makes that number up with shares submitted recently and how fast. it can go from 12-14 depending on luck (and probably a greater range than that. the numbers that should match are the accepted shares on both the pool and miner.

[nlive]

Where are you mine?
I can only slush mining.
There any way mining 50btc?
thanks....

[Pinwheel]

Where are you mine?
I can only slush mining.
There any way mining 50btc?
thanks....

I mine on btcguild.com. and also on coinotron.com for altcoins.