cryptograd (OP)
Member
Offline
Activity: 112
Merit: 10
|
|
June 22, 2013, 08:59:33 PM Last edit: June 25, 2013, 03:35:13 AM by cryptograd |
|
After trying several different methods this is the quickest and most efficient I've found. *[UPDATE] 350Mhz found to run stable and consistent on STOCK Avalon 1) Download https://dl.dropboxusercontent.com/u/16881231/avalon_clone/firmware/openwrt-ar71xx-generic-tl-wr703n-v1-squashfs-factory_20130519b.bin2) Flash this image onto your unit by accessing your unit @192.168.0.100 and going to System -> Backup / Flash Firmware 3) REBOOT UNIT(delete any custom scripts u might have prior) 4) Go to Status -> Cgminer Configuration and under "Chip Frequency" select 350, then SAVE & APPLY these changes 5) Configure your pool difficulty properly(@Slush's pool its 64) 6) HASH LIKE A BTCEAST My unit is completely stock and never opened. I keep it in a temperature controlled room. This image will make fans run constantly at maximum. WILL UPLOAD UPDATE IMAGE IN A FEW HOURSmy specs are: fan1 fan2 fan32400 3840 3720 temp1 temp2 temp3 24 38 43 Ebereon has confirmed that electrical consumption @350mhz is 720 Watts I have my overclocked Avalon at Slush's pool for over 24 hours now. At these speeds I believe 10 rounds is about 8 hours of hashing. Also I've noticed that cooling plays a definite almost immediate factor. HAPPY HASHING
|
|
|
|
|
|
It is a common myth that Bitcoin is ruled by a majority of miners. This is not true. Bitcoin miners "vote" on the ordering of transactions, but that's all they do. They can't vote to change the network rules.
|
|
|
Advertised sites are not endorsed by the Bitcoin Forum. They may be unsafe, untrustworthy, or illegal in your jurisdiction.
|
|
|
farproc
Sr. Member
Offline
Activity: 406
Merit: 250
ALGORY.io Crowdsale starts on 8/12/2017
|
|
June 22, 2013, 09:46:03 PM |
|
Thanks.
|
|
|
|
Keninishna
|
|
June 23, 2013, 12:30:51 AM |
|
I'm trying this out now and seems good so far, I think ckolivas was able to get 81 gh/s stable but I'm scared to push my avalon and break it
|
|
|
|
cryptograd (OP)
Member
Offline
Activity: 112
Merit: 10
|
|
June 23, 2013, 12:40:54 AM |
|
I'm trying this out now and seems good so far, I think ckolivas was able to get 81 gh/s stable but I'm scared to push my avalon and break it +1 This is a 325Mhz configuration In order to achieve anything higher youd have to overclock to 350Mhz... and on a STOCK avalon you risk several complications. This is the only STABLE STOCK OVERCLOCK. All others require a PSU upgrade, additional cooling, more thermal paste etc
|
|
|
|
dxtwo
Full Member
Offline
Activity: 145
Merit: 100
coins...coins...as far as you can see
|
|
June 23, 2013, 01:04:34 AM Last edit: June 23, 2013, 01:23:30 AM by dxtwo |
|
Which files did you modify? I skimmed over the source a few days ago and looked at the timing/frequencies in a few of the packages. Was it just as simple as adding the option to the menu and having cgminer do the rest with the passed value?
Also mind posting a checksum?
I was just getting ready to start messing around with building new firmware, but you beat me to it. Thanks!
|
|
|
|
cryptograd (OP)
Member
Offline
Activity: 112
Merit: 10
|
|
June 23, 2013, 03:42:22 PM |
|
Which files did you modify? I skimmed over the source a few days ago and looked at the timing/frequencies in a few of the packages. Was it just as simple as adding the option to the menu and having cgminer do the rest with the passed value?
Also mind posting a checksum?
I was just getting ready to start messing around with building new firmware, but you beat me to it. Thanks!
This is the simplest upgrade possible. The image self contains all modifications. After running this at a properly configured pool I am realizing Bitcoin reward that equals out to a 88Gh/s payout(2.3 BTC in a 24 hr cycle) My machine never idles, never stalls, no reboot so far. Perfect stable consitant flawless hashing
|
|
|
|
scyth3
|
|
June 23, 2013, 05:11:29 PM |
|
What temps are considered too high? Thanks
|
|
|
|
cryptograd (OP)
Member
Offline
Activity: 112
Merit: 10
|
|
June 23, 2013, 08:15:42 PM |
|
What temps are considered too high? Thanks
You want to keep things under 48 for optimum performance. Over 50 your unit is considered to be overheating.
|
|
|
|
delaria
Member
Offline
Activity: 85
Merit: 10
|
|
June 23, 2013, 09:15:07 PM |
|
Hi there, thanks for this update! do you have any idea if this would work on a batch 1 ?
Cheers
|
|
|
|
cryptograd (OP)
Member
Offline
Activity: 112
Merit: 10
|
|
June 23, 2013, 09:56:01 PM |
|
Hi there, thanks for this update! do you have any idea if this would work on a batch 1 ?
Cheers
I don't see why not, but I know batch 1 has a slightly lower rated PSU and less thermal paste, as well as having tighter spaced modules which seems to increase heat concentration. Seems like batch 2 was made for higher heat levels and better ventilation as well as more power consumption. Modify at your own risk
|
|
|
|
delaria
Member
Offline
Activity: 85
Merit: 10
|
|
June 23, 2013, 09:57:09 PM |
|
Hi there, thanks for this update! do you have any idea if this would work on a batch 1 ?
Cheers
I don't see why not, but I know batch 1 has a slightly lower rated PSU and less thermal paste, as well as having tighter spaced modules which seems to increase heat concentration. Seems like batch 2 was made for higher heat levels and better ventilation as well as more power consumption. Modify at your own risk I've just tried it on a batch 1 and it works. Cool. Thank you!
|
|
|
|
Elokane
|
|
June 23, 2013, 09:57:30 PM |
|
What's the risk if temperature stays low?
|
|
|
|
delaria
Member
Offline
Activity: 85
Merit: 10
|
|
June 23, 2013, 10:11:52 PM |
|
What's the risk if temperature stays low?
If you push it too far in terms of Mhz, you may cause undervolting in other components, which may cause serious hardware failures. So far i'm seeing a "Utility" higher than 17 with values of 350 Mhz. Anything higher than that brings up hardware errors and lowers utility.
|
|
|
|
Fassade
Member
Offline
Activity: 71
Merit: 10
|
|
June 23, 2013, 10:12:29 PM |
|
Yesterday I tried making the change of the PSU (batch 1) for a Corsair TX850W and working properly. Then, I flash the Avalon with the indicated binary from here and I have it running at 325 Mhz, the only detail is that the fans are always at 100% but it's a minor detail, I prefer more noise to have problems in the chips.
One question: as some pictures I've seen, BitSyncom used thermal paste applied directly but does not make good contact between the surface of the board to the heatsink surface.
It will work better if you install a thermal pad (0.3 mm thick)?
Regards.
|
|
|
|
cryptograd (OP)
Member
Offline
Activity: 112
Merit: 10
|
|
June 23, 2013, 10:14:08 PM |
|
What's the risk if temperature stays low?
None! Unless you are depending on ur stock fans to achieve this(you would blowout your stock PSU) This modification provides stable power consumption from your stock equipment. Ideally youd want to cool the room to 65F or liquid cool the unit I temperature control the room to 70F to comfortably get a healthy 77Gh/s at the box. As mentioned before a good properly configured pool( https://mining.bitcoin.cz/) will increase your earnings in way that resembles hashing @88Gh/s
|
|
|
|
cryptograd (OP)
Member
Offline
Activity: 112
Merit: 10
|
|
June 23, 2013, 10:16:16 PM Last edit: July 05, 2013, 02:25:59 AM by cryptograd |
|
What's the risk if temperature stays low?
If you push it too far in terms of Mhz, you may cause undervolting in other components, which may cause serious hardware failures. So far i'm seeing a "Utility" higher than 17 with values of 350 Mhz. Anything higher than that brings up hardware errors and lowers utility. +1 this but this thread was initially about overclocking a STOCK Avalon to 325Mhz350Mhz is not something I would do to a stock Avalon without direct liquid cooling
|
|
|
|
elasticband
Legendary
Offline
Activity: 1036
Merit: 1000
Nighty Night Don't Let The Trolls Bite Nom Nom Nom
|
|
June 23, 2013, 10:30:53 PM |
|
Ive been running all day on 345 no problems...... apart from bliwing the power in ky house but that was due to way to many things runni g at once..... women my room runs around 20c during the day and less at night
|
|
|
|
Elokane
|
|
June 23, 2013, 10:48:42 PM |
|
What's the risk if temperature stays low?
None! Unless you are depending on ur stock fans to achieve this(you would blowout your stock PSU) This modification provides stable power consumption from your stock equipment. So stock or no stock for 77Gh/s?
|
|
|
|
elasticband
Legendary
Offline
Activity: 1036
Merit: 1000
Nighty Night Don't Let The Trolls Bite Nom Nom Nom
|
|
June 23, 2013, 10:52:09 PM |
|
|
|
|
|
scyth3
|
|
June 23, 2013, 11:11:23 PM |
|
Are those accepted shares in the same time frame and difficulty?
|
|
|
|
elasticband
Legendary
Offline
Activity: 1036
Merit: 1000
Nighty Night Don't Let The Trolls Bite Nom Nom Nom
|
|
June 23, 2013, 11:15:32 PM |
|
I havr been running 2 3 4 for 2 weeks or so and 1 since friday
|
|
|
|
scyth3
|
|
June 23, 2013, 11:17:18 PM |
|
I havr been running 2 3 4 for 2 weeks or so and 1 since friday
oh, so you just showing off
|
|
|
|
cryptograd (OP)
Member
Offline
Activity: 112
Merit: 10
|
|
June 23, 2013, 11:19:05 PM |
|
What's the risk if temperature stays low?
None! Unless you are depending on ur stock fans to achieve this(you would blowout your stock PSU) This modification provides stable power consumption from your stock equipment. So stock or no stock for 77Gh/s? Everything in this thread from me is about a STOCK batch 2 Avalon I havr been running 2 3 4 for 2 weeks or so and 1 since friday
What pool is that?
|
|
|
|
Elokane
|
|
June 23, 2013, 11:21:22 PM |
|
I'm sorry, I was just confused because you said:
"Unless you are depending on ur stock fans to achieve this(you would blowout your stock PSU)"
|
|
|
|
elasticband
Legendary
Offline
Activity: 1036
Merit: 1000
Nighty Night Don't Let The Trolls Bite Nom Nom Nom
|
|
June 23, 2013, 11:21:38 PM |
|
guild
slushs normally gives higher values....
|
|
|
|
delaria
Member
Offline
Activity: 85
Merit: 10
|
|
June 24, 2013, 12:08:48 AM |
|
batch 1 and 2 batch 2 devices running at 350 Mhz.
|
|
|
|
elasticband
Legendary
Offline
Activity: 1036
Merit: 1000
Nighty Night Don't Let The Trolls Bite Nom Nom Nom
|
|
June 24, 2013, 12:18:08 AM |
|
Batch 1 do jot have as big a psu as batch 2...... be careful I had issues with my batch 1 units after a while
|
|
|
|
delaria
Member
Offline
Activity: 85
Merit: 10
|
|
June 24, 2013, 12:26:20 AM |
|
Batch 1 do jot have as big a psu as batch 2...... be careful I had issues with my batch 1 units after a while
Which kind of issues specifically ? Thank you!
|
|
|
|
elasticband
Legendary
Offline
Activity: 1036
Merit: 1000
Nighty Night Don't Let The Trolls Bite Nom Nom Nom
|
|
June 24, 2013, 12:29:02 AM |
|
Well the fan with the blue light on 2 of my batch 1 unit struggles a little... it does not like full speed, so this woukd cut out after a while, many hw errors, heat and SICK once or twice.
what temps do your batch 1 normally run on 300?
|
|
|
|
SolarSilver
Legendary
Offline
Activity: 1112
Merit: 1000
|
|
June 24, 2013, 12:31:02 AM |
|
Batch 1 do jot have as big a psu as batch 2...... be careful I had issues with my batch 1 units after a while
The Batch #1 units with the default power supply pull about 760 Watts at the wall plug when pushed to 350 MHz
|
|
|
|
elasticband
Legendary
Offline
Activity: 1036
Merit: 1000
Nighty Night Don't Let The Trolls Bite Nom Nom Nom
|
|
June 24, 2013, 12:31:23 AM |
|
batch 1 and 2 batch 2 devices running at 350 Mhz. 350mhz x 240chips = 84000ghs. One of your units is loosing 4000ghs from that. They have 650 psu? 350mhz requires a 750 I think
|
|
|
|
SolarSilver
Legendary
Offline
Activity: 1112
Merit: 1000
|
|
June 24, 2013, 12:32:01 AM |
|
what temps do your batch 1 normally run on 300?
Largely depends on the intake termp, but I have not seen it go over 50 to 51 degrees Celcius (fan speed just goes up)
|
|
|
|
elasticband
Legendary
Offline
Activity: 1036
Merit: 1000
Nighty Night Don't Let The Trolls Bite Nom Nom Nom
|
|
June 24, 2013, 12:33:35 AM |
|
Mine generally run around 50 this could be to do with the fans struggling to reach max
|
|
|
|
bitcad
Newbie
Offline
Activity: 59
Merit: 0
|
|
June 24, 2013, 12:47:41 AM |
|
Can verify it works with my batch 2 unit. Currently getting 82-83GH/s on BTC Guild. Thanks!
|
|
|
|
delaria
Member
Offline
Activity: 85
Merit: 10
|
|
June 24, 2013, 12:57:51 AM |
|
batch 1 and 2 batch 2 devices running at 350 Mhz. 350mhz x 240chips = 84000ghs. One of your units is loosing 4000ghs from that. They have 650 psu? 350mhz requires a 750 I think The units are pulling at the wall ( i have a power meter ) 2.25 kW. I will replace the batch 1 PSU with a 1000 W unit. that should fix the issue you mention.
|
|
|
|
elasticband
Legendary
Offline
Activity: 1036
Merit: 1000
Nighty Night Don't Let The Trolls Bite Nom Nom Nom
|
|
June 24, 2013, 01:07:45 AM |
|
I think a 750 or 850 will do the job unless you plan on upgrading to 4 modules later
Wattage / 3 * 4 is what u need fir 4 modules.
I would stop running your batch 1 with overclock until u uo grade though
|
|
|
|
cryptograd (OP)
Member
Offline
Activity: 112
Merit: 10
|
|
June 24, 2013, 01:40:32 AM |
|
IVE OVERCLOCKED MY STOCK BATCH 2 TO RUN @350MHZ FOR A STABLE 85Gh/s!!!
Original post edited
|
|
|
|
jspielberg
|
|
June 24, 2013, 01:44:01 AM |
|
Congrats!!!!Though maybe ease off the coffee a little... (or is that a hash rush?) I can't wait for mass shipping!
|
|
|
|
crazyearner
Legendary
Offline
Activity: 1820
Merit: 1001
|
|
June 24, 2013, 04:17:43 AM |
|
if taking them over the stock speed are you not prone to risking over heating less life time of chip and also void your warranty if something goes wrong with it?
|
|
|
|
elasticband
Legendary
Offline
Activity: 1036
Merit: 1000
Nighty Night Don't Let The Trolls Bite Nom Nom Nom
|
|
June 24, 2013, 08:52:26 AM |
|
9h 34m 30s 81931.77
getworks 1238 accepted 20556 rejected 93 HW 1312
setting 345..... apaprently this works better than 350.... can anyone compare
|
|
|
|
rudrigorc2
Legendary
Offline
Activity: 1064
Merit: 1000
|
|
June 24, 2013, 09:01:52 AM |
|
4h 27m 11s 82523.42 @ 345 750HW - 50btc 3h 13m 47s 81915.67 @ 345 1324HW - ozcoin
|
|
|
|
strombom
Member
Offline
Activity: 77
Merit: 10
|
|
June 24, 2013, 11:47:06 AM |
|
if taking them over the stock speed are you not prone to risking over heating less life time of chip and also void your warranty if something goes wrong with it?
I have been running for more than a month at 345-370MHz, it's still stable. When the chip hangs to overheating it seems to just stop and cool down, then you have to restart the unit... I don't think there is any warranty to void in the first place
|
|
|
|
dogie
Legendary
Offline
Activity: 1666
Merit: 1183
dogiecoin.com
|
|
June 24, 2013, 02:56:33 PM |
|
Is anyone able to compile a firmware where the fans still throttle, or a way to change that manually? I need to sleep next to this thing.
Also a way to set max temp to 48/49? One of the modules sits on 47 which triggers max RPMs, although I can hopefully move this to somewhere a bit cooler.
|
|
|
|
Dalkore
Legendary
Offline
Activity: 1330
Merit: 1026
Mining since 2010 & Hosting since 2012
|
|
June 24, 2013, 04:04:21 PM |
|
How do I load the image? I didn't see a USB port. Thank you.
-D
|
Hosting: Low as $60.00 per KW - LinkTransaction List: jayson3 +5 - ColdHardMetal +3 - Nolo +2 - CoinHoarder +1 - Elxiliath +1 - tymm0 +1 - Johnniewalker +1 - Oscer +1 - Davidj411 +1 - BitCoiner2012 +1 - dstruct2k +1 - Philj +1 - camolist +1 - exahash +1 - Littleshop +1 - Severian +1 - DebitMe +1 - lepenguin +1 - StringTheory +1 - amagimetals +1 - jcoin200 +1 - serp +1 - klintay +1 - -droid- +1 - FlutterPie +1
|
|
|
elasticband
Legendary
Offline
Activity: 1036
Merit: 1000
Nighty Night Don't Let The Trolls Bite Nom Nom Nom
|
|
June 24, 2013, 04:39:40 PM |
|
Is anyone able to compile a firmware where the fans still throttle, or a way to change that manually? I need to sleep next to this thing.
Also a way to set max temp to 48/49? One of the modules sits on 47 which triggers max RPMs, although I can hopefully move this to somewhere a bit cooler.
unlucky......
|
|
|
|
Elokane
|
|
June 24, 2013, 06:07:10 PM |
|
How do I load the image? I didn't see a USB port. Thank you.
-D
On the menu you see when you connect to it through the net.
|
|
|
|
Dalkore
Legendary
Offline
Activity: 1330
Merit: 1026
Mining since 2010 & Hosting since 2012
|
|
June 24, 2013, 11:42:54 PM |
|
How do I load the image? I didn't see a USB port. Thank you.
-D
On the menu you see when you connect to it through the net. What does "connect to it through the net"? There is a place to upload it via the firmware update menu. Are you saying there is a way to grab it off the internet? -D
|
Hosting: Low as $60.00 per KW - LinkTransaction List: jayson3 +5 - ColdHardMetal +3 - Nolo +2 - CoinHoarder +1 - Elxiliath +1 - tymm0 +1 - Johnniewalker +1 - Oscer +1 - Davidj411 +1 - BitCoiner2012 +1 - dstruct2k +1 - Philj +1 - camolist +1 - exahash +1 - Littleshop +1 - Severian +1 - DebitMe +1 - lepenguin +1 - StringTheory +1 - amagimetals +1 - jcoin200 +1 - serp +1 - klintay +1 - -droid- +1 - FlutterPie +1
|
|
|
SolarSilver
Legendary
Offline
Activity: 1112
Merit: 1000
|
|
June 25, 2013, 12:13:06 AM |
|
What does "connect to it through the net"? There is a place to upload it via the firmware update menu. Are you saying there is a way to grab it off the internet?
You first download the firmware onto your local system and then tell the browser to upload to the Avalon For example you download the image from http://ck.kolivas.org/apps/cgminer/avalon/20130624/openwrt-ar71xx-generic-tl-wr703n-v1-squashfs-factory.binand then you browse to System -> Backup / Flash Firmware Click on Browse, select the image you just downloaded from you Downloads an click on Flash Image Then Ack the hash (if you want to check) and reflash the machine. Wait 3 minutes and log back in, running the new image. By the way, are *you* the guy selling the ASIC managed hosting? I'm offering to do managed hosting of 1 unit Avalon with 3 hashing units for EUR 100 / month in Belgium eh... never mind... why do I even bother to bring this up... At least I've been reflashing embedded devices for the last 19 years.... it's really not that difficult if even I can pull it off...
|
|
|
|
Sitarow
Legendary
Offline
Activity: 1792
Merit: 1047
|
|
June 25, 2013, 04:31:17 AM |
|
What does "connect to it through the net"? There is a place to upload it via the firmware update menu. Are you saying there is a way to grab it off the internet?
You first download the firmware onto your local system and then tell the browser to upload to the Avalon For example you download the image from http://ck.kolivas.org/apps/cgminer/avalon/20130624/openwrt-ar71xx-generic-tl-wr703n-v1-squashfs-factory.binand then you browse to System -> Backup / Flash Firmware Click on Browse, select the image you just downloaded from you Downloads an click on Flash Image Then Ack the hash (if you want to check) and reflash the machine. Wait 3 minutes and log back in, running the new image. By the way, are *you* the guy selling the ASIC managed hosting? I'm offering to do managed hosting of 1 unit Avalon with 3 hashing units for EUR 100 / month in Belgium eh... never mind... why do I even bother to bring this up... At least I've been reflashing embedded devices for the last 19 years.... it's really not that difficult if even I can pull it off... I will test this and post the results after 24hrs.
|
|
|
|
dan99
|
|
June 25, 2013, 04:37:43 AM |
|
copy his positing from another thread "
BitSyncom Sr. Member
Re: Avalon stable @ 98,986Mhash/sec Today at 04:11:37 AM Reply with quote #21 was wondering how long it'd take people to notice ( and more importantly share the constant that we've released on github.)
the number you are all aiming for is 450 Tongue of course, that's not really possible on just air cooling.
|
|
|
|
crazyearner
Legendary
Offline
Activity: 1820
Merit: 1001
|
|
July 02, 2013, 02:13:09 PM |
|
Looking forward to seeing how this progresses in terms of overclocknig on stock cooling to going water cooled
|
|
|
|
MagicMike523
Newbie
Offline
Activity: 58
Merit: 0
|
|
July 02, 2013, 03:01:53 PM |
|
if taking them over the stock speed are you not prone to risking over heating less life time of chip and also void your warranty if something goes wrong with it?
I have been running for more than a month at 345-370MHz, it's still stable. When the chip hangs to overheating it seems to just stop and cool down, then you have to restart the unit... I don't think there is any warranty to void in the first place I don't think you know what stable means
|
|
|
|
crazyearner
Legendary
Offline
Activity: 1820
Merit: 1001
|
|
July 04, 2013, 09:57:11 PM |
|
Hello I have a question. Is their a way to bypass the TP-LINK TL-WR703N v1 and use your own router and then use cgminer to mine with. I have a friend who has a problem with his TP-LINK TL-WR703N v1 as it is not connecting up to his pc or laptp, however all lights are showing on including on the board for the tp link and lights on avalon shows solid green light and other light yellow stays on but cant connect up.
Any ideas how to bypass TP and use own router and cgminer and configure?
|
|
|
|
SolarSilver
Legendary
Offline
Activity: 1112
Merit: 1000
|
|
July 04, 2013, 11:12:18 PM |
|
Hello I have a question. Is their a way to bypass the TP-LINK TL-WR703N v1 and use your own router and then use cgminer to mine with.
Yes, you can connect the USB cable from from the TP-LINK to a computer running cgminer but you need to tweak a jumper to prevent the port to provide 5V: https://en.bitcoin.it/wiki/Avalon#FPGA_controller I have a friend who has a problem with his TP-LINK TL-WR703N v1 as it is not connecting up to his pc or laptp, however all lights are showing on including on the board for the tp link and lights on avalon shows solid green light and other light yellow stays on but cant connect up.
Any ideas how to bypass TP and use own router and cgminer and configure?
You have a friend who can't post to this forum? My doctor also gets questions about things friend of mine contracted in a back alley... is the same case? ;-) https://www.youtube.com/watch?v=OZHAiTl81tAAnyways, there have been a few people running their own version of cgminer on an i386 and connect over USB to the avalon modules https://bitcointalk.org/index.php?topic=150482.msg1606249#msg1606249But it surprises me he can't get the TP-LINK to work, they all get tested over wifi at the assembly plant. Are you sure his ethernet setup is correct?
|
|
|
|
crazyearner
Legendary
Offline
Activity: 1820
Merit: 1001
|
|
July 05, 2013, 01:02:04 AM |
|
Hello I have a question. Is their a way to bypass the TP-LINK TL-WR703N v1 and use your own router and then use cgminer to mine with.
Yes, you can connect the USB cable from from the TP-LINK to a computer running cgminer but you need to tweak a jumper to prevent the port to provide 5V: https://en.bitcoin.it/wiki/Avalon#FPGA_controller I have a friend who has a problem with his TP-LINK TL-WR703N v1 as it is not connecting up to his pc or laptp, however all lights are showing on including on the board for the tp link and lights on avalon shows solid green light and other light yellow stays on but cant connect up.
Any ideas how to bypass TP and use own router and cgminer and configure?
You have a friend who can't post to this forum? My doctor also gets questions about things friend of mine contracted in a back alley... is the same case? ;-) https://www.youtube.com/watch?v=OZHAiTl81tAAnyways, there have been a few people running their own version of cgminer on an i386 and connect over USB to the avalon modules https://bitcointalk.org/index.php?topic=150482.msg1606249#msg1606249But it surprises me he can't get the TP-LINK to work, they all get tested over wifi at the assembly plant. Are you sure his ethernet setup is correct? I havg oen through a call with him and he has tried everything possible and is getting no where with it. I will contact him when he is around and see if can get the above to work
|
|
|
|
Lathanium
Newbie
Offline
Activity: 43
Merit: 0
|
|
July 05, 2013, 01:57:12 AM Last edit: July 05, 2013, 05:37:10 AM by Lathanium |
|
Hello I have a question. Is their a way to bypass the TP-LINK TL-WR703N v1 and use your own router and then use cgminer to mine with.
Yes, you can connect the USB cable from from the TP-LINK to a computer running cgminer but you need to tweak a jumper to prevent the port to provide 5V: https://en.bitcoin.it/wiki/Avalon#FPGA_controller I have a friend who has a problem with his TP-LINK TL-WR703N v1 as it is not connecting up to his pc or laptp, however all lights are showing on including on the board for the tp link and lights on avalon shows solid green light and other light yellow stays on but cant connect up.
Any ideas how to bypass TP and use own router and cgminer and configure?
You have a friend who can't post to this forum? My doctor also gets questions about things friend of mine contracted in a back alley... is the same case? ;-) https://www.youtube.com/watch?v=OZHAiTl81tAAnyways, there have been a few people running their own version of cgminer on an i386 and connect over USB to the avalon modules https://bitcointalk.org/index.php?topic=150482.msg1606249#msg1606249But it surprises me he can't get the TP-LINK to work, they all get tested over wifi at the assembly plant. Are you sure his ethernet setup is correct? I'm the fella who can't get his ethernet card to work on his avalon. I've tried multiple computers and used network switches and nothing. Not a damn thing. So I guess i'll get a linux box going to get this thing started and wait for ebay to deliver me a new WR703N router eh. Like the vid by the way lol Edit: Update, as I was doing an OpenWrt Failsafe which worked fine, I noticed i had to jam my ethernet cord unusually hard into the tp-link router. Upon inspection of the router one of the ethernet pins was bent out of shape. Go figure some tester bent the crap out of it. Works fine now. thx everyone for the help
|
|
|
|
Dalkore
Legendary
Offline
Activity: 1330
Merit: 1026
Mining since 2010 & Hosting since 2012
|
|
July 05, 2013, 08:11:14 PM |
|
I am doing this upgrade and I will report back. I also have been playing with other modifications and they have been doing well.
|
Hosting: Low as $60.00 per KW - LinkTransaction List: jayson3 +5 - ColdHardMetal +3 - Nolo +2 - CoinHoarder +1 - Elxiliath +1 - tymm0 +1 - Johnniewalker +1 - Oscer +1 - Davidj411 +1 - BitCoiner2012 +1 - dstruct2k +1 - Philj +1 - camolist +1 - exahash +1 - Littleshop +1 - Severian +1 - DebitMe +1 - lepenguin +1 - StringTheory +1 - amagimetals +1 - jcoin200 +1 - serp +1 - klintay +1 - -droid- +1 - FlutterPie +1
|
|
|
cryptograd (OP)
Member
Offline
Activity: 112
Merit: 10
|
|
July 05, 2013, 10:02:50 PM Last edit: July 05, 2013, 10:44:24 PM by cryptograd |
|
UPDATE
345mhz is best with this build. STABLE, fans on 100%, low hardware errors. 82 - 84 Gh/s 700 watts
Unit can run unaffected at temps up to 55C like this. Which means ANY and ALL can benefit from this post. No extra cooling measures necessary.
My final comment on this.
|
|
|
|
Dalkore
Legendary
Offline
Activity: 1330
Merit: 1026
Mining since 2010 & Hosting since 2012
|
|
July 06, 2013, 06:47:53 PM |
|
UPDATE
345mhz is best with this build. STABLE, fans on 100%, low hardware errors. 82 - 84 Gh/s 700 watts
Unit can run unaffected at temps up to 55C like this. Which means ANY and ALL can benefit from this post. No extra cooling measures necessary.
My final comment on this.
Does this image set the fans to 100% or do I need to do that myself? If so, how to I manually set the fans to 100 without bypassing them connecting to the board? Thanks
|
Hosting: Low as $60.00 per KW - LinkTransaction List: jayson3 +5 - ColdHardMetal +3 - Nolo +2 - CoinHoarder +1 - Elxiliath +1 - tymm0 +1 - Johnniewalker +1 - Oscer +1 - Davidj411 +1 - BitCoiner2012 +1 - dstruct2k +1 - Philj +1 - camolist +1 - exahash +1 - Littleshop +1 - Severian +1 - DebitMe +1 - lepenguin +1 - StringTheory +1 - amagimetals +1 - jcoin200 +1 - serp +1 - klintay +1 - -droid- +1 - FlutterPie +1
|
|
|
|
ecliptic
|
|
July 06, 2013, 09:38:45 PM |
|
UPDATE
345mhz is best with this build. STABLE, fans on 100%, low hardware errors. 82 - 84 Gh/s 700 watts
Unit can run unaffected at temps up to 55C like this. Which means ANY and ALL can benefit from this post. No extra cooling measures necessary.
My final comment on this.
Does this image set the fans to 100% or do I need to do that myself? If so, how to I manually set the fans to 100 without bypassing them connecting to the board? Thanks FWIW - Often 100% fan speed gets you only marginal improvement over say, 80% fan speed, but significantly decreases the lifespan of the fan. Not a big deal if you can replace them (and the unit automatically shuts off to prevent overheating) though
|
|
|
|
Bitconian
Member
Offline
Activity: 101
Merit: 10
|
|
July 07, 2013, 08:48:09 AM |
|
http://fotos.subefotos.com/3a957d21c3184832f1e69a8234b89179o.jpgI got a peak of 94Gh/s.... is that safe? I got it @ 300Mhz with autoclock, but my average is around 80Gh/s right now the noise is pretty high. Are my fans and temperature safe? Fan 1 = 2760 Fan 2 = 3480 Fan 3 = 3480 Temp 1 = 25 Temp 2 = 45 Temp 3= 48 thanks! B.
|
You can make me smile 1GEUEBTm6XfRuqAswrR6LbofnMq6VN5A5P
|
|
|
Dalkore
Legendary
Offline
Activity: 1330
Merit: 1026
Mining since 2010 & Hosting since 2012
|
|
July 07, 2013, 08:36:12 PM |
|
Those temps look good. Don't let them go much higher though. These fans are made to run under full load. It will just be loud. I updated mine and they are all running 80~ +.
|
Hosting: Low as $60.00 per KW - LinkTransaction List: jayson3 +5 - ColdHardMetal +3 - Nolo +2 - CoinHoarder +1 - Elxiliath +1 - tymm0 +1 - Johnniewalker +1 - Oscer +1 - Davidj411 +1 - BitCoiner2012 +1 - dstruct2k +1 - Philj +1 - camolist +1 - exahash +1 - Littleshop +1 - Severian +1 - DebitMe +1 - lepenguin +1 - StringTheory +1 - amagimetals +1 - jcoin200 +1 - serp +1 - klintay +1 - -droid- +1 - FlutterPie +1
|
|
|
dogie
Legendary
Offline
Activity: 1666
Merit: 1183
dogiecoin.com
|
|
July 07, 2013, 09:40:44 PM |
|
There really isn't much harm running them hotter - these chips are spec'ed and tested up to 70C, even then its really unlikely the lifetime of the chips would be < useful lifetime... AND 1 chip death doesn't matter in this design.
I'm getting similar temperatures at similar fan speeds but with a 33C ambient [yeah, fml].
|
|
|
|
cryptograd (OP)
Member
Offline
Activity: 112
Merit: 10
|
|
July 08, 2013, 04:34:36 AM |
|
yes you are cooling efficiently. what build is this that you are running? Alsobyou should only consider the top MHSav number when declaring your Gh/s rate.
|
|
|
|
cryptograd (OP)
Member
Offline
Activity: 112
Merit: 10
|
|
July 08, 2013, 04:37:45 AM |
|
UPDATE
345mhz is best with this build. STABLE, fans on 100%, low hardware errors. 82 - 84 Gh/s 700 watts
Unit can run unaffected at temps up to 55C like this. Which means ANY and ALL can benefit from this post. No extra cooling measures necessary.
My final comment on this.
Does this image set the fans to 100% or do I need to do that myself? If so, how to I manually set the fans to 100 without bypassing them connecting to the board? Thanks FWIW - Often 100% fan speed gets you only marginal improvement over say, 80% fan speed, but significantly decreases the lifespan of the fan. Not a big deal if you can replace them (and the unit automatically shuts off to prevent overheating) though not true inappropriate cooling will lead to higher hardware failures... thus more restarts and down time.
|
|
|
|
Beans
|
|
July 25, 2013, 03:52:19 AM |
|
UPDATE
345mhz is best with this build. STABLE, fans on 100%, low hardware errors. 82 - 84 Gh/s 700 watts
Unit can run unaffected at temps up to 55C like this. Which means ANY and ALL can benefit from this post. No extra cooling measures necessary.
My final comment on this.
Does this image set the fans to 100% or do I need to do that myself? If so, how to I manually set the fans to 100 without bypassing them connecting to the board? Thanks FWIW - Often 100% fan speed gets you only marginal improvement over say, 80% fan speed, but significantly decreases the lifespan of the fan. Not a big deal if you can replace them (and the unit automatically shuts off to prevent overheating) though not true inappropriate cooling will lead to higher hardware failures... thus more restarts and down time. Inappropriate cooling is putting the garden hose on it. Higher airflow is not going to damage anything.
|
|
|
|
Beans
|
|
July 25, 2013, 03:57:15 AM |
|
I set mine to 350 and it seems to be stable. Temps are 11,35,35. It's got cold air blowing on it though. Definitely not crashing like my Butterfly units do, I have to turn them back on at least once a day.
|
|
|
|
szuetam
|
|
July 26, 2013, 12:23:52 AM |
|
How to set 100% fans?
|
|
|
|
SolarSilver
Legendary
Offline
Activity: 1112
Merit: 1000
|
|
July 26, 2013, 08:01:06 AM |
|
|
|
|
|
szuetam
|
|
July 26, 2013, 08:25:36 AM |
|
Thank you
|
|
|
|
szuetam
|
|
July 26, 2013, 08:36:23 AM |
|
How many HW per 5 minutes are you getting, and with which speed temp etc?
Im getting about 550HW/5minutes with freq 375 f1 3000 f2 3720 f3 3960 t1 20 t2 37 t3 40
|
|
|
|
|