jstefanop (OP)
Legendary
 Offline
Activity: 2086
Merit: 1390
|
 |
December 02, 2017, 05:20:10 PM |
|
Hey there jstefanop, just received my order a couple of days ago, and it seems like one of my miners has an issue where it runs normally for a brief period of time (avg 2-min hashrate of ~4.1 running at 756), and after a few minutes, it ramps down to ~2.7 or so, and that's where it stays. I have two other units that work fine, and do not exhibit this behavior. I've tried adjusting the core voltage a bit (swept the from 0.7 - 0.825), but nothing seemed to have an effect. Didn't alter mem voltage. Another note is that I don't notice this drop when I run at lower frequencies; at 684 for example, all three sticks seems to have a avg 2-min hashrate of 1.75.
Not sure if it helps, but its unit #2815. Any thoughts or suggestions? Got a multimeter in case that's useful. Thanks in advance!
I wouldnt be worried unless your average hashrate, and pool hashrate (the last two numbers) show lower than expected hash. Also try isolating that miner to see if its a hub/power issue. |
|
|
|
|
|
|
You get merit points when someone likes your post enough to give you some. And for every 2 merit points you receive, you can send 1 merit point to someone else!
|
|
|
Advertised sites are not endorsed by the Bitcoin Forum. They may be unsafe, untrustworthy, or illegal in your jurisdiction.
|
|
|
|
|
|
Megaquake
|
|
December 02, 2017, 08:35:01 PM |
|
I will ask here also.
Why are these needing to be built by HolyScott before shipping?
HolyScott-
I was not expecting labor to have to build and put them all together
|
Mines at Kano.is best profit in the world!
在Kano.is的BTC
|
|
|
dora-gt
Newbie
Offline
Activity: 9
Merit: 0
|
|
December 02, 2017, 10:53:05 PM |
|
similar to yellowshark, my landers are ... MLD 0: | 0.0/ 0.0/ 0.0 h/s | A: 0 R:0+0(none) HW: 0/none
MLD 1: | 3.94/ 3.59/ 3.74Mh/s | A: 53 R:0+0(none) HW: 0/none
MLD 2: | 0.0/ 0.0/ 0.0 h/s | A: 0 R:0+0(none) HW: 0/none
MLD 3: | 3.88/ 3.85/ 3.97Mh/s | A: 59 R:0+0(none) HW: 1/.21%
MLD 4: | 0.0/ 0.0/ 0.0 h/s | A: 0 R:0+0(none) HW: 0/none
MLD 5: | 3.88/ 3.85/ 3.98Mh/s | A: 66 R:0+0(none) HW: 0/none
MLD 6: | 3.87/ 4.00/ 3.92Mh/s | A: 66 R:0+0(none) HW: 1/.21%
MLD 7: | 0.0/ 0.0/ 0.0 h/s | A: 0 R:0+0(none) HW: 0/none
MLD 8: | 3.84/ 3.82/ 4.08Mh/s | A: 60 R:0+0(none) HW: 0/none
MLD 9: | 3.80/ 3.84/ 3.86Mh/s | A: 64 R:0+0(none) HW: 5/1.1%
MLD10: | 3.81/ 3.85/ 4.29Mh/s | A: 78 R:0+0(none) HW: 0/none
MLD11: | 3.90/ 3.81/ 3.89Mh/s | A: 73 R:0+0(none) HW: 1/.21%
MLD12: | 3.81/ 3.80/ 4.10Mh/s | A: 60 R:0+0(none) HW: 0/none
MLD13: | 3.88/ 3.85/ 3.95Mh/s | A: 74 R:0+0(none) HW: 0/none
MLD14: | 0.0/ 0.0/ 0.0 h/s | A: 0 R:0+0(none) HW: 0/none
MLD15: | 0.0/ 0.0/ 0.0 h/s | A: 0 R:0+0(none) HW: 0/none
MLD16: | 565.5/544.4/564.6kh/s | A: 9 R:0+0(none) HW: 0/none
MLD17: | 58.0/ 45.7/ 33.2kh/s | A: 0 R:0+0(none) HW: 0/none
MLD18: | 3.86/ 3.85/ 4.11Mh/s | A: 67 R:0+0(none) HW: 0/none
MLD19: | 60.3/ 51.1/ 74.7kh/s | A: 5 R:0+0(none) HW: 0/none
MLD20: | 2.52/ 2.87/ 3.02Mh/s | A: 44 R:0+0(none) HW: 1/.27%
MLD21: | 3.90/ 3.93/ 4.24Mh/s | A: 74 R:0+0(none) HW: 1/.20%
MLD22: | 3.89/ 3.82/ 4.07Mh/s | A: 72 R:0+0(none) HW: 0/none
MLD23: | 2.57/ 2.93/ 3.26Mh/s | A: 44 R:0+0(none) HW: 0/none
MLD24: | 0.0/ 0.0/ 0.0 h/s | A: 0 R:0+0(none) HW: 0/none
MLD25: | 2.38/ 2.75/ 2.89Mh/s | A: 50 R:0+0(none) HW: 0/none
MLD26: | 0.0/ 0.0/ 0.0 h/s | A: 0 R:0+0(none) HW: 0/none
MLD27: | 2.43/ 3.00/ 3.16Mh/s | A: 47 R:0+0(none) HW: 0/none
MLD28: | 3.89/ 3.84/ 3.90Mh/s | A: 54 R:0+0(none) HW: 1/.21%
MLD29: | 2.56/ 2.93/ 2.87Mh/s | A: 42 R:0+0(none) HW: 0/none
MLD30: | 330.2/315.8/240.8kh/s | A: 7 R:0+0(none) HW: 0/none
MLD31: | 0.0/ 0.0/ 0.0 h/s | A: 0 R:0+0(none) HW: 0/none
MLD32: | 3.90/ 3.85/ 3.84Mh/s | A: 60 R:0+0(none) HW: 0/none
MLD33: | 3.92/ 4.01/ 4.18Mh/s | A: 55 R:0+0(none) HW: 1/.20%
MLD34: | 3.87/ 3.84/ 3.85Mh/s | A: 53 R:0+0(none) HW: 0/none
MLD35: | 0.0/ 0.0/ 0.0 h/s | A: 0 R:0+0(none) HW: 0/none
MLD36: | 3.85/ 3.84/ 3.89Mh/s | A: 74 R:0+0(none) HW: 0/none
MLD37: | 3.83/ 3.86/ 4.12Mh/s | A: 71 R:0+0(none) HW: 0/none
MLD38: | 3.90/ 3.85/ 4.40Mh/s | A: 59 R:0+0(none) HW: 4/.75%
MLD39: | 3.93/ 3.86/ 4.43Mh/s | A: 68 R:0+0(none) HW: 0/none
MLD40: | 3.84/ 3.79/ 3.69Mh/s | A: 59 R:0+0(none) HW: 2/.45%
MLD41: | 3.02/ 3.59/ 4.00Mh/s | A: 47 R:0+0(none) HW: 0/none
MLD42: | 1.92/ 1.31/ 1.16Mh/s | A: 24 R:0+0(none) HW: 0/none
MLD43: | 3.90/ 3.81/ 4.03Mh/s | A: 75 R:0+0(none) HW: 1/.21%
MLD44: | 0.0/ 0.0/ 0.0 h/s | A: 0 R:0+0(none) HW: 0/none
MLD45: | 0.0/ 0.0/ 0.0 h/s | A: 0 R:0+0(none) HW: 0/none
MLD46: | 3.86/ 3.80/ 3.74Mh/s | A: 59 R:0+0(none) HW: 0/none
MLD47: | 521.5/380.5/307.2kh/s | A: 6 R:0+0(none) HW: 0/none
MLD48: | 3.93/ 3.87/ 4.03Mh/s | A: 63 R:0+0(none) HW: 1/.21%
MLD49: | 3.84/ 3.79/ 4.12Mh/s | A: 64 R:0+0(none) HW: 4/.80%
MLD50: | 0.0/ 0.0/ 0.0 h/s | A: 0 R:0+0(none) HW: 0/none
MLD51: | 1.41/ 1.24/ 1.20Mh/s | A: 15 R:0+0(none) HW: 0/none
MLD52: | 2.61/ 2.75/ 2.87Mh/s | A: 46 R:0+0(none) HW: 0/none
MLD53: | 0.0/ 0.0/ 0.0 h/s | A: 0 R:0+0(none) HW: 0/none
MLD54: | 0.0/ 0.0/ 0.0 h/s | A: 0 R:0+0(none) HW: 0/none
MLD55: | 3.92/ 3.88/ 4.13Mh/s | A: 81 R:0+0(none) HW: 1/.20%
MLD56: | 0.0/ 0.0/ 0.0 h/s | A: 0 R:0+0(none) HW: 0/none
MLD57: | 2.97/ 3.57/ 3.75Mh/s | A: 51 R:0+0(none) HW: 0/none
MLD58: | 279.0/253.1/274.0kh/s | A: 8 R:0+0(none) HW: 0/none
MLD59: | 3.88/ 3.83/ 3.84Mh/s | A: 57 R:0+0(none) HW: 0/none
MLD60: | 0.0/ 0.0/ 0.0 h/s | A: 0 R:0+0(none) HW: 0/none
MLD61: | 0.0/ 0.0/ 0.0 h/s | A: 0 R:0+0(none) HW: 0/none
MLD62: | 2.54/ 2.39/ 2.51Mh/s | A: 39 R:0+0(none) HW: 0/none
MLD63: | 3.90/ 3.85/ 4.09Mh/s | A: 56 R:0+0(none) HW: 0/none
MLD64: | 0.0/ 0.0/ 0.0 h/s | A: 0 R:0+0(none) HW: 0/none
MLD65: | 3.84/ 3.80/ 4.29Mh/s | A: 62 R:0+0(none) HW: 2/.39%
MLD66: | 0.0/ 0.0/ 0.0 h/s | A: 0 R:0+0(none) HW: 0/none
MLD67: | 3.87/ 4.01/ 3.99Mh/s | A: 40 R:0+0(none) HW: 1/.21%
MLD68: | 180.0/148.8/149.5kh/s | A: 8 R:0+0(none) HW: 0/none
MLD69: | 739.5/656.6/722.3kh/s | A: 16 R:0+0(none) HW: 2/2.2%
MLD70: | 0.0/ 0.0/ 0.0 h/s | A: 0 R:0+0(none) HW: 0/none
MLD71: | 3.89/ 3.85/ 3.68Mh/s | A: 57 R:0+0(none) HW: 0/none
MLD72: | 3.87/ 3.82/ 3.92Mh/s | A: 66 R:0+0(none) HW: 0/none
MLD73: | 3.90/ 3.85/ 3.84Mh/s | A: 56 R:0+0(none) HW: 2/.43%
MLD74: | 1.26/ 0.98/ 0.99Mh/s | A: 12 R:0+0(none) HW: 0/none
there are 2 types of problem. 1) not working at all (it may be USB trouble but my power supply is very strong) 2) dropping down to kH/s idk why... I really want auto restart function. So I'm running 75 landers now, it outputs only 160MH/s... I'm sad... |
|
|
|
|
aarons6
Legendary
Offline
Activity: 1736
Merit: 1006
|
|
December 02, 2017, 10:53:43 PM |
|
I will ask here also.
Why are these needing to be built by HolyScott before shipping?
HolyScott-
I was not expecting labor to have to build and put them all together
he is putting them together so he can test them first.. i asked. i guess he didnt feel comfortable just sending them out untested. |
|
|
|
|
aarons6
Legendary
Offline
Activity: 1736
Merit: 1006
|
|
December 02, 2017, 10:55:12 PM |
|
similar to yellowshark, my landers are ... MLD 0: | 0.0/ 0.0/ 0.0 h/s | A: 0 R:0+0(none) HW: 0/none
MLD 1: | 3.94/ 3.59/ 3.74Mh/s | A: 53 R:0+0(none) HW: 0/none
MLD 2: | 0.0/ 0.0/ 0.0 h/s | A: 0 R:0+0(none) HW: 0/none
MLD 3: | 3.88/ 3.85/ 3.97Mh/s | A: 59 R:0+0(none) HW: 1/.21%
MLD 4: | 0.0/ 0.0/ 0.0 h/s | A: 0 R:0+0(none) HW: 0/none
MLD 5: | 3.88/ 3.85/ 3.98Mh/s | A: 66 R:0+0(none) HW: 0/none
MLD 6: | 3.87/ 4.00/ 3.92Mh/s | A: 66 R:0+0(none) HW: 1/.21%
MLD 7: | 0.0/ 0.0/ 0.0 h/s | A: 0 R:0+0(none) HW: 0/none
MLD 8: | 3.84/ 3.82/ 4.08Mh/s | A: 60 R:0+0(none) HW: 0/none
MLD 9: | 3.80/ 3.84/ 3.86Mh/s | A: 64 R:0+0(none) HW: 5/1.1%
MLD10: | 3.81/ 3.85/ 4.29Mh/s | A: 78 R:0+0(none) HW: 0/none
MLD11: | 3.90/ 3.81/ 3.89Mh/s | A: 73 R:0+0(none) HW: 1/.21%
MLD12: | 3.81/ 3.80/ 4.10Mh/s | A: 60 R:0+0(none) HW: 0/none
MLD13: | 3.88/ 3.85/ 3.95Mh/s | A: 74 R:0+0(none) HW: 0/none
MLD14: | 0.0/ 0.0/ 0.0 h/s | A: 0 R:0+0(none) HW: 0/none
MLD15: | 0.0/ 0.0/ 0.0 h/s | A: 0 R:0+0(none) HW: 0/none
MLD16: | 565.5/544.4/564.6kh/s | A: 9 R:0+0(none) HW: 0/none
MLD17: | 58.0/ 45.7/ 33.2kh/s | A: 0 R:0+0(none) HW: 0/none
MLD18: | 3.86/ 3.85/ 4.11Mh/s | A: 67 R:0+0(none) HW: 0/none
MLD19: | 60.3/ 51.1/ 74.7kh/s | A: 5 R:0+0(none) HW: 0/none
MLD20: | 2.52/ 2.87/ 3.02Mh/s | A: 44 R:0+0(none) HW: 1/.27%
MLD21: | 3.90/ 3.93/ 4.24Mh/s | A: 74 R:0+0(none) HW: 1/.20%
MLD22: | 3.89/ 3.82/ 4.07Mh/s | A: 72 R:0+0(none) HW: 0/none
MLD23: | 2.57/ 2.93/ 3.26Mh/s | A: 44 R:0+0(none) HW: 0/none
MLD24: | 0.0/ 0.0/ 0.0 h/s | A: 0 R:0+0(none) HW: 0/none
MLD25: | 2.38/ 2.75/ 2.89Mh/s | A: 50 R:0+0(none) HW: 0/none
MLD26: | 0.0/ 0.0/ 0.0 h/s | A: 0 R:0+0(none) HW: 0/none
MLD27: | 2.43/ 3.00/ 3.16Mh/s | A: 47 R:0+0(none) HW: 0/none
MLD28: | 3.89/ 3.84/ 3.90Mh/s | A: 54 R:0+0(none) HW: 1/.21%
MLD29: | 2.56/ 2.93/ 2.87Mh/s | A: 42 R:0+0(none) HW: 0/none
MLD30: | 330.2/315.8/240.8kh/s | A: 7 R:0+0(none) HW: 0/none
MLD31: | 0.0/ 0.0/ 0.0 h/s | A: 0 R:0+0(none) HW: 0/none
MLD32: | 3.90/ 3.85/ 3.84Mh/s | A: 60 R:0+0(none) HW: 0/none
MLD33: | 3.92/ 4.01/ 4.18Mh/s | A: 55 R:0+0(none) HW: 1/.20%
MLD34: | 3.87/ 3.84/ 3.85Mh/s | A: 53 R:0+0(none) HW: 0/none
MLD35: | 0.0/ 0.0/ 0.0 h/s | A: 0 R:0+0(none) HW: 0/none
MLD36: | 3.85/ 3.84/ 3.89Mh/s | A: 74 R:0+0(none) HW: 0/none
MLD37: | 3.83/ 3.86/ 4.12Mh/s | A: 71 R:0+0(none) HW: 0/none
MLD38: | 3.90/ 3.85/ 4.40Mh/s | A: 59 R:0+0(none) HW: 4/.75%
MLD39: | 3.93/ 3.86/ 4.43Mh/s | A: 68 R:0+0(none) HW: 0/none
MLD40: | 3.84/ 3.79/ 3.69Mh/s | A: 59 R:0+0(none) HW: 2/.45%
MLD41: | 3.02/ 3.59/ 4.00Mh/s | A: 47 R:0+0(none) HW: 0/none
MLD42: | 1.92/ 1.31/ 1.16Mh/s | A: 24 R:0+0(none) HW: 0/none
MLD43: | 3.90/ 3.81/ 4.03Mh/s | A: 75 R:0+0(none) HW: 1/.21%
MLD44: | 0.0/ 0.0/ 0.0 h/s | A: 0 R:0+0(none) HW: 0/none
MLD45: | 0.0/ 0.0/ 0.0 h/s | A: 0 R:0+0(none) HW: 0/none
MLD46: | 3.86/ 3.80/ 3.74Mh/s | A: 59 R:0+0(none) HW: 0/none
MLD47: | 521.5/380.5/307.2kh/s | A: 6 R:0+0(none) HW: 0/none
MLD48: | 3.93/ 3.87/ 4.03Mh/s | A: 63 R:0+0(none) HW: 1/.21%
MLD49: | 3.84/ 3.79/ 4.12Mh/s | A: 64 R:0+0(none) HW: 4/.80%
MLD50: | 0.0/ 0.0/ 0.0 h/s | A: 0 R:0+0(none) HW: 0/none
MLD51: | 1.41/ 1.24/ 1.20Mh/s | A: 15 R:0+0(none) HW: 0/none
MLD52: | 2.61/ 2.75/ 2.87Mh/s | A: 46 R:0+0(none) HW: 0/none
MLD53: | 0.0/ 0.0/ 0.0 h/s | A: 0 R:0+0(none) HW: 0/none
MLD54: | 0.0/ 0.0/ 0.0 h/s | A: 0 R:0+0(none) HW: 0/none
MLD55: | 3.92/ 3.88/ 4.13Mh/s | A: 81 R:0+0(none) HW: 1/.20%
MLD56: | 0.0/ 0.0/ 0.0 h/s | A: 0 R:0+0(none) HW: 0/none
MLD57: | 2.97/ 3.57/ 3.75Mh/s | A: 51 R:0+0(none) HW: 0/none
MLD58: | 279.0/253.1/274.0kh/s | A: 8 R:0+0(none) HW: 0/none
MLD59: | 3.88/ 3.83/ 3.84Mh/s | A: 57 R:0+0(none) HW: 0/none
MLD60: | 0.0/ 0.0/ 0.0 h/s | A: 0 R:0+0(none) HW: 0/none
MLD61: | 0.0/ 0.0/ 0.0 h/s | A: 0 R:0+0(none) HW: 0/none
MLD62: | 2.54/ 2.39/ 2.51Mh/s | A: 39 R:0+0(none) HW: 0/none
MLD63: | 3.90/ 3.85/ 4.09Mh/s | A: 56 R:0+0(none) HW: 0/none
MLD64: | 0.0/ 0.0/ 0.0 h/s | A: 0 R:0+0(none) HW: 0/none
MLD65: | 3.84/ 3.80/ 4.29Mh/s | A: 62 R:0+0(none) HW: 2/.39%
MLD66: | 0.0/ 0.0/ 0.0 h/s | A: 0 R:0+0(none) HW: 0/none
MLD67: | 3.87/ 4.01/ 3.99Mh/s | A: 40 R:0+0(none) HW: 1/.21%
MLD68: | 180.0/148.8/149.5kh/s | A: 8 R:0+0(none) HW: 0/none
MLD69: | 739.5/656.6/722.3kh/s | A: 16 R:0+0(none) HW: 2/2.2%
MLD70: | 0.0/ 0.0/ 0.0 h/s | A: 0 R:0+0(none) HW: 0/none
MLD71: | 3.89/ 3.85/ 3.68Mh/s | A: 57 R:0+0(none) HW: 0/none
MLD72: | 3.87/ 3.82/ 3.92Mh/s | A: 66 R:0+0(none) HW: 0/none
MLD73: | 3.90/ 3.85/ 3.84Mh/s | A: 56 R:0+0(none) HW: 2/.43%
MLD74: | 1.26/ 0.98/ 0.99Mh/s | A: 12 R:0+0(none) HW: 0/none
there are 2 types of problem. 1) not working at all (it may be USB trouble but my power supply is very strong) 2) dropping down to kH/s idk why... I really want auto restart function. So I'm running 75 landers now, it outputs only 160MH/s... I'm sad... your problem is usb speed.. try upping the worker difficulty.. i found if you have it too low, say 64 or 128 and multiple sticks... they get jammed up after awhile. also minera has a restart option. it works great. |
|
|
|
|
yellowshark
Newbie
Offline
Activity: 2
Merit: 0
|
|
December 02, 2017, 11:20:53 PM
Last edit: December 03, 2017, 03:52:15 PM by yellowshark |
|
Hey there jstefanop, just received my order a couple of days ago, and it seems like one of my miners has an issue where it runs normally for a brief period of time (avg 2-min hashrate of ~4.1 running at 756), and after a few minutes, it ramps down to ~2.7 or so, and that's where it stays. I have two other units that work fine, and do not exhibit this behavior. I've tried adjusting the core voltage a bit (swept the from 0.7 - 0.825), but nothing seemed to have an effect. Didn't alter mem voltage. Another note is that I don't notice this drop when I run at lower frequencies; at 684 for example, all three sticks seems to have a avg 2-min hashrate of 1.75.
Not sure if it helps, but its unit #2815. Any thoughts or suggestions? Got a multimeter in case that's useful. Thanks in advance!
I wouldnt be worried unless your average hashrate, and pool hashrate (the last two numbers) show lower than expected hash. Also try isolating that miner to see if its a hub/power issue. Thanks for the reply. Definitely have excluded the USB ports: my two other miners seem to operate fine on the same port(s); both are very stable for long runs, one at 832mhz and the other at 796mhz. And sorry I didn't mention it originally, but yes: the average hashrate and the pool hashrate both trend downwards, once this "throttling" kicks in. Currently I'm running it at 700mhz / .75v core / 0.9v mem; for the first ten minutes, it hashed at about 3.8Mh/s, but then it throttled around that time, and the values have now settled at 2.63 / 2.68 / 2.76Mh/s after running for about 25 minutes total. That's what happens pretty much every time I run them: two run great, but this one throttles down to 2.7Mh/s, and I can't seem to get it to hash above that rate unless I restart BFGMiner. On a side note, it sounds very similar to what soifigured described in this post: Got some assembled and up and running. I'm noticing some are slowing down to about 2MH after running for an hour or so. Is this a self preservation feature? Are they running too hot? I hit all the small heatsinks with my pyrometer and temps are all about 60C.
Thanks again for all the help, appreciate you taking the time to help us out. *Edit: I might have found a sweet spot for the voltages on this miner, I dropped the memory down quite a bit and currently I'm having a nice run with it at 756mhz, using core voltage of 0.73v and memory voltage of 0.79v. The values currently being reported by bfgminer are 4.25 / 4.22 / 4.29Mh/s, and it's been running for ~15 mins or so. I kept mulling over the fact that the miner was just being throttled, but still was basically healthy, for all intents and purposes. So I decided to try reducing the stock voltages a bit and see how things go. Will let you guys know if this works out for me, gonna give let it run overnight. ** Final edit: results of the overnight run are good. All three miners are working great now. |
|
|
|
|
RdStrcklnd
Jr. Member
Offline
Activity: 70
Merit: 1
|
|
December 02, 2017, 11:49:40 PM |
|
[/quote]
your problem is usb speed.. try upping the worker difficulty.. i found if you have it too low, say 64 or 128 and multiple sticks... they get jammed up after awhile.
also minera has a restart option. it works great.
[/quote]
How do you get them to run on Minera? I know how to get Minera on a Pi, but is it just plug and play from there?
|
|
|
|
|
|
Megaquake
|
|
December 03, 2017, 12:22:34 AM |
|
These no longer will work on NH
| 19.48/19.40/ 8.94Mh/s | A:1 R:0+0(none) 0 days 00:08:16], one share 8 minutes lol
[2017-12-02 19:16:59] Stratum from pool 2 detected new block
[2017-12-02 19:17:05] Stratum from pool 2 detected new block
[2017-12-02 19:17:32] Network difficulty changed to 984k ( 7.04Th)
[2017-12-02 19:17:32] Stratum from pool 2 detected new block
[2017-12-02 19:19:01] Stratum from pool 2 detected new block
[2017-12-02 19:19:31] Network difficulty changed to 993k ( 7.11Th)
[2017-12-02 19:19:31] Stratum from pool 2 detected new block
[2017-12-02 19:19:44] Network difficulty changed to 1.19M ( 8.51Th)
[2017-12-02 19:19:44] Stratum from pool 2 detected new block
[2017-12-02 19:20:07] Network difficulty changed to 1.48M (10.62Th)
[2017-12-02 19:20:07] Stratum from pool 2 detected new block
[2017-12-02 19:20:57] Stratum from pool 2 detected new block
[2017-12-02 19:21:52] Network difficulty changed to 1.62M (11.61Th)
[2017-12-02 19:21:52] Stratum from pool 2 detected new block
[2017-12-02 19:22:00] Network difficulty changed to 1.84M (13.19Th)
[2017-12-02 19:22:00] Stratum from pool 2 detected new block
[2017-12-02 19:22:13] Stratum from pool 2 detected new block
[2017-12-02 19:23:37] Network difficulty changed to 2.01M (14.42Th)
[2017-12-02 19:23:37] Stratum from pool 2 detected new block
|
Mines at Kano.is best profit in the world!
在Kano.is的BTC
|
|
|
aarons6
Legendary
Offline
Activity: 1736
Merit: 1006
|
|
December 03, 2017, 12:25:32 AM
Last edit: December 04, 2017, 06:59:42 PM by aarons6 |
|
These no longer will work on NH
| 19.48/19.40/ 8.94Mh/s | A:1 R:0+0(none) 0 days 00:08:16], one share 8 minutes lol
[2017-12-02 19:16:59] Stratum from pool 2 detected new block
[2017-12-02 19:17:05] Stratum from pool 2 detected new block
[2017-12-02 19:17:32] Network difficulty changed to 984k ( 7.04Th)
[2017-12-02 19:17:32] Stratum from pool 2 detected new block
[2017-12-02 19:19:01] Stratum from pool 2 detected new block
[2017-12-02 19:19:31] Network difficulty changed to 993k ( 7.11Th)
[2017-12-02 19:19:31] Stratum from pool 2 detected new block
[2017-12-02 19:19:44] Network difficulty changed to 1.19M ( 8.51Th)
[2017-12-02 19:19:44] Stratum from pool 2 detected new block
[2017-12-02 19:20:07] Network difficulty changed to 1.48M (10.62Th)
[2017-12-02 19:20:07] Stratum from pool 2 detected new block
[2017-12-02 19:20:57] Stratum from pool 2 detected new block
[2017-12-02 19:21:52] Network difficulty changed to 1.62M (11.61Th)
[2017-12-02 19:21:52] Stratum from pool 2 detected new block
[2017-12-02 19:22:00] Network difficulty changed to 1.84M (13.19Th)
[2017-12-02 19:22:00] Stratum from pool 2 detected new block
[2017-12-02 19:22:13] Stratum from pool 2 detected new block
[2017-12-02 19:23:37] Network difficulty changed to 2.01M (14.42Th)
[2017-12-02 19:23:37] Stratum from pool 2 detected new block
i havent tested mine on nh, but they dont work on zpool or multipool.us sorry i meant prohashing :/ try putting #skipcbcheck on the url after the port number. |
|
|
|
|
|
Megaquake
|
|
December 03, 2017, 12:28:38 AM |
|
These no longer will work on NH
| 19.48/19.40/ 8.94Mh/s | A:1 R:0+0(none) 0 days 00:08:16], one share 8 minutes lol
[2017-12-02 19:16:59] Stratum from pool 2 detected new block
[2017-12-02 19:17:05] Stratum from pool 2 detected new block
[2017-12-02 19:17:32] Network difficulty changed to 984k ( 7.04Th)
[2017-12-02 19:17:32] Stratum from pool 2 detected new block
[2017-12-02 19:19:01] Stratum from pool 2 detected new block
[2017-12-02 19:19:31] Network difficulty changed to 993k ( 7.11Th)
[2017-12-02 19:19:31] Stratum from pool 2 detected new block
[2017-12-02 19:19:44] Network difficulty changed to 1.19M ( 8.51Th)
[2017-12-02 19:19:44] Stratum from pool 2 detected new block
[2017-12-02 19:20:07] Network difficulty changed to 1.48M (10.62Th)
[2017-12-02 19:20:07] Stratum from pool 2 detected new block
[2017-12-02 19:20:57] Stratum from pool 2 detected new block
[2017-12-02 19:21:52] Network difficulty changed to 1.62M (11.61Th)
[2017-12-02 19:21:52] Stratum from pool 2 detected new block
[2017-12-02 19:22:00] Network difficulty changed to 1.84M (13.19Th)
[2017-12-02 19:22:00] Stratum from pool 2 detected new block
[2017-12-02 19:22:13] Stratum from pool 2 detected new block
[2017-12-02 19:23:37] Network difficulty changed to 2.01M (14.42Th)
[2017-12-02 19:23:37] Stratum from pool 2 detected new block
i havent tested mine on nh, but they dont work on zpool or multipool.us :/ try putting #skipcbcheck on the url after the port number. Yea that is a known issue having to use /#skipcbcheck using scrypt algo with bfgminer, that will not help with the difficulty, I even tried to set a minimum diff in the password field, did not help |
Mines at Kano.is best profit in the world!
在Kano.is的BTC
|
|
|
|
Megaquake
|
|
December 03, 2017, 12:31:38 AM |
|
Need a list of scrypt pools these are not compatible with, you cannot mine on pro hashing either
|
Mines at Kano.is best profit in the world!
在Kano.is的BTC
|
|
|
StSchil
Newbie
Offline
Activity: 1
Merit: 0
|
|
December 03, 2017, 12:41:47 AM |
|
Hello,
I will preface the following statement by saying that I am a 100% newbie to mining and know just about enough about computers to make myself dangerous, but also know that I'm a Hands On type learner and must dive in and try things. So on to my question:
I got my 4 Moonlander2s in the mail last week and hadn't had much of a chance to toy with them until today. I followed the set up instructions, downloaded the drivers and other software and got them up and running in no time flat. I ran them for about 15 mins and they were all hashing like crazy, it was then I realized that there was one very important step left out of the set up, at least for noobs like me; Where and how does one edit the file to insert our own personal user name, password, and wallet address for the distribution of the his/her share of the block reward?
Thanks in advance to anyone willing to point me in the right direction.
Steve
|
|
|
|
|
jstefanop (OP)
Legendary
Offline
Activity: 2086
Merit: 1390
|
|
December 03, 2017, 01:08:35 AM |
|
These no longer will work on NH
| 19.48/19.40/ 8.94Mh/s | A:1 R:0+0(none) 0 days 00:08:16], one share 8 minutes lol
[2017-12-02 19:16:59] Stratum from pool 2 detected new block
[2017-12-02 19:17:05] Stratum from pool 2 detected new block
[2017-12-02 19:17:32] Network difficulty changed to 984k ( 7.04Th)
[2017-12-02 19:17:32] Stratum from pool 2 detected new block
[2017-12-02 19:19:01] Stratum from pool 2 detected new block
[2017-12-02 19:19:31] Network difficulty changed to 993k ( 7.11Th)
[2017-12-02 19:19:31] Stratum from pool 2 detected new block
[2017-12-02 19:19:44] Network difficulty changed to 1.19M ( 8.51Th)
[2017-12-02 19:19:44] Stratum from pool 2 detected new block
[2017-12-02 19:20:07] Network difficulty changed to 1.48M (10.62Th)
[2017-12-02 19:20:07] Stratum from pool 2 detected new block
[2017-12-02 19:20:57] Stratum from pool 2 detected new block
[2017-12-02 19:21:52] Network difficulty changed to 1.62M (11.61Th)
[2017-12-02 19:21:52] Stratum from pool 2 detected new block
[2017-12-02 19:22:00] Network difficulty changed to 1.84M (13.19Th)
[2017-12-02 19:22:00] Stratum from pool 2 detected new block
[2017-12-02 19:22:13] Stratum from pool 2 detected new block
[2017-12-02 19:23:37] Network difficulty changed to 2.01M (14.42Th)
[2017-12-02 19:23:37] Stratum from pool 2 detected new block
i havent tested mine on nh, but they dont work on zpool or multipool.us :/ try putting #skipcbcheck on the url after the port number. Yea that is a known issue having to use /#skipcbcheck using scrypt algo with bfgminer, that will not help with the difficulty, I even tried to set a minimum diff in the password field, did not help They are running, just the pool diff is very high for these. Like I said most pools are not designed to run anything slower than 200-500 MH these days. Some pools have an option to set the diff in the password field (for example litecoinpool password "d=128" sets the diff to 128. 128 or 256 is a good value for these for shares every few seconds. Past that it will take minutes or longer for you to see a share. If pools don't have this, id contact them and ask for a "low diff port" (under 512) for USB miners. Technically as long as the red LED is flashing constantly and hash rate displayed is good, it dosent matter that your submitted shares at a lower rate, just payout variance will be higher. |
|
|
|
RdStrcklnd
Jr. Member
Offline
Activity: 70
Merit: 1
|
|
December 03, 2017, 01:53:49 AM |
|
Hello,
I will preface the following statement by saying that I am a 100% newbie to mining and know just about enough about computers to make myself dangerous, but also know that I'm a Hands On type learner and must dive in and try things. So on to my question:
I got my 4 Moonlander2s in the mail last week and hadn't had much of a chance to toy with them until today. I followed the set up instructions, downloaded the drivers and other software and got them up and running in no time flat. I ran them for about 15 mins and they were all hashing like crazy, it was then I realized that there was one very important step left out of the set up, at least for noobs like me; Where and how does one edit the file to insert our own personal user name, password, and wallet address for the distribution of the his/her share of the block reward?
Thanks in advance to anyone willing to point me in the right direction.
Steve
Check out Astrali's instructions on the first page, you want the part where you use nano. |
|
|
|
|
RdStrcklnd
Jr. Member
Offline
Activity: 70
Merit: 1
|
|
December 03, 2017, 02:34:32 AM |
|
Can anyone help with using Minera with a Moonlander2 USB stick and a Pi 3b? I know how to get Minera on the Pi and access it via it's IP on my computer, but is it just plug and play or are there additional steps after that?
|
|
|
|
|
hurlgr
Newbie
Offline
Activity: 5
Merit: 0
|
|
December 03, 2017, 03:26:58 AM |
|
Pre-ordered the Moonlander 2 a couple months ago and it arrived today. Thanks for this thread. Have it up and mining, all tuned in thanks to this!
|
|
|
|
|
jstefanop (OP)
Legendary
Offline
Activity: 2086
Merit: 1390
|
|
December 03, 2017, 08:04:55 AM |
|
Can anyone help with using Minera with a Moonlander2 USB stick and a Pi 3b? I know how to get Minera on the Pi and access it via it's IP on my computer, but is it just plug and play or are there additional steps after that?
At the very least you would need to replace the bfgminer binaries it generates with my supplied RPi binaries (just copy over bfgminer executable). After I get the next version out that fixes some bugs ill probably be able to merge it into main branch. |
|
|
|
aarons6
Legendary
Offline
Activity: 1736
Merit: 1006
|
|
December 03, 2017, 08:11:52 AM |
|
Can anyone help with using Minera with a Moonlander2 USB stick and a Pi 3b? I know how to get Minera on the Pi and access it via it's IP on my computer, but is it just plug and play or are there additional steps after that?
At the very least you would need to replace the bfgminer binaries it generates with my supplied RPi binaries (just copy over bfgminer executable). After I get the next version out that fixes some bugs ill probably be able to merge it into main branch. just copy the bfgminer to the minera custom folder.. it needs to be renamed to bfgminer-futurebit2 |
|
|
|
|
Astrali
Full Member
Offline
Activity: 281
Merit: 130
Crypto Addicted
|
|
December 03, 2017, 12:27:58 PM |
|
Hello,
I will preface the following statement by saying that I am a 100% newbie to mining and know just about enough about computers to make myself dangerous, but also know that I'm a Hands On type learner and must dive in and try things. So on to my question:
I got my 4 Moonlander2s in the mail last week and hadn't had much of a chance to toy with them until today. I followed the set up instructions, downloaded the drivers and other software and got them up and running in no time flat. I ran them for about 15 mins and they were all hashing like crazy, it was then I realized that there was one very important step left out of the set up, at least for noobs like me; Where and how does one edit the file to insert our own personal user name, password, and wallet address for the distribution of the his/her share of the block reward?
Thanks in advance to anyone willing to point me in the right direction.
Steve
hi, as RdStrcklnd already mentioned - i made a step by step instruction for use on linux enviroments like raspberry pi (without having the device in my hands actually). Do you run it on windows or linux enviroment? You need to do the changes in the "start" file you are using - its either an .sh file on linux or a .bat file on windows. this one needs editing. the address after -u is the username and in many cases is your receiving wallet address. we need more info to help you  Greetings - Astrali |
|
|
|
philipma1957
Legendary
Offline
Activity: 4102
Merit: 7714
'The right to privacy matters'
|
|
December 03, 2017, 01:36:03 PM |
|
|
|
|
|
|
