Official ASICMINER Block Erupter Europe

[simpic]

@simpic
Will answer outstanding mail tonight/tomorrow
If it is the order I have in mind it seems that your local mail provider has lost the parcel
We will ship again

Solved! Item finally received.
Thank you anyway

Keep up the good work

It seems i have a new problem.
The Blade seems not to work propertly.
Do i write here or speak by email/PM?

Thank you.

[1715234554]

1715234554

[1715234554]

1715234554

[simpic]

It seems i have a new problem.
The Blade seems not to work propertly.
Do i write here or speak by email/PM?

Thank you.

The Blade rarely reaches 8000 MH/s then it goes down in a couple of minutes.

I'm using an ATX 120W (12V @ 10A) power supply and two 12'' fans for cooling it.
I have also measured temperature and power consumption: they are about 40° and 91W.
I tried with other power supply, even an ATX 750W but nothing changes.

Is this Blade broken?

[2GOOD]

Use stratum proxy !!!

[EnJoyThis]

yxt will you also be selling the ASICMINER USB hub which can hold 49 BE's?

[simpic]

Use stratum proxy !!!

Yes, i did it yesterday and it worked
Sorry.

Why it's needed? What does it change?

[mijanur]

yxt will you also be selling the ASICMINER USB hub which can hold 49 BE's?

any news?

[yxt]

@simpic
Will answer outstanding mail tonight/tomorrow
If it is the order I have in mind it seems that your local mail provider has lost the parcel
We will ship again

Solved! Item finally received.
Thank you anyway

Keep up the good work

thx, looked into it few minutes after it was delivered, thats why I don't have answered again.

Use stratum proxy !!!

Yes, i did it yesterday and it worked
Sorry.

Why it's needed? What does it change?

@2GOOD thx


blades supports only the old getwork protocol  https://en.bitcoin.it/wiki/Getwork
stratum is a new protocol, used by most pools https://en.bitcoin.it/wiki/Stratum

you can use a pool which support getwork directly, btcmp.com for example
For best results use a (local) stratum proxy. An R-Pi is sufficient for this completely

[yxt]

49 port USB HUBs in stock! Unfortunately, only a very limited number  
I have not received any info when I get more.

Therefore, only one hub per order (at least 50 miners USB) for free, while supplies last and I like you

[Pieh0]

Damn, should have waited a week

[BitAddict]

That 49 usb hub looks so cool!

[mastahofdesastah]

asap when I find the time to check them.
By law and ToS we have 30 days time

You checkt them or you need more time? Only 8 Days are left by your ToS. I would be happy to see my BTC again...

Thank you
Mastah

[Ollie]

Is an ATX power with at least 25 A from 5 V pins required to use the USB HUB at full capacity of 49 erupters?

[yxt]

Is an ATX power with at least 25 A from 5 V pins required to use the USB HUB at full capacity of 49 erupters?

yes

[PMB]

Is an ATX power with at least 25 A from 5 V pins required to use the USB HUB at full capacity of 49 erupters?

Hi Olie,

510mA * 49 = 24990 / 1000 = 24,99 Amp

So it should be enough... 25 Amp is an ATX supply.... Hum.. about 500W ATX psu will be more than enough ( I think it has about 42A on the 5V Rail). 

best regards,

P.

[Pieh0]

Sounds like an opportunity to abuse the 12v line was missed on these hubs .

[yxt]

see it as a cool "power on mod" for your blade PSU

[Pieh0]

Yea, suppose that's a bonus then, 5v rail for usb's, 12v for blades. Less PSU's to blow up

[yxt]

Is an ATX power with at least 25 A from 5 V pins required to use the USB HUB at full capacity of 49 erupters?

Hi Olie,

510mA * 49 = 24990 / 1000 = 24,99 Amp

So it should be enough... 25 Amp is an ATX supply.... Hum.. about 500W ATX psu will be more than enough ( I think it has about 42A on the 5V Rail). 

best regards,

P.

the 500W is typical for the 12V rail, you have to check the datasheet to be sure

[Mudbankkeith]

see it as a cool "power on mod" for your blade PSU

Hashing power instead of a paper clip.

My old psu crashes out if I only draw on the 12v rail, the fan controller appears to only look at the 5v rail.(old but unused 450w)

[gidi337]

I hope no one minds this post

but i am now selling a limited stock of overclocking kits (up to 14.7gh/s) for the new version blades shipping from the UK

see here

https://bitcointalk.org/index.php?topic=322161.0


for more information see here

https://bitcointalk.org/index.php?topic=310752.msg3343981#msg3343981

Instructions on applying the kit
http://www.gekkoscience.com/be_ins/blade_ins.html