PhoenixMiner 6.2c: fastest Ethereum/Ethash miner with lowest devfee (Win/Linux)

[samfei]

My 1st GPU not connected to monitor.

GPU 1
https://prnt.sc/u1ftfd

Other GPU
https://prnt.sc/u1fuxz

GPU-Z shows that on 1st GPU 215+Mb videomemory is in use... That's why it's not enough to mine eth.

In ports of 1st GPU inserted something? If you use igpu Windows didn't use other GPU memory... Something wrong here...

nothing inserted at gpu 1 and already set igpu enable in bios.  

[UnclWish]

My 1st GPU not connected to monitor.

GPU 1
https://prnt.sc/u1ftfd

Other GPU
https://prnt.sc/u1fuxz

GPU-Z shows that on 1st GPU 215+Mb videomemory is in use... That's why it's not enough to mine eth.

In ports of 1st GPU inserted something? If you use igpu Windows didn't use other GPU memory... Something wrong here...

nothing inserted at gpu 1 and already set igpu enable in bios.  

Don't know than what's wrong with your comp... Try to search info about your motherboard... Maybe it's need to update mobo bios...
Try to delete AMD drivers via DDU and install again.

[samfei]

My 1st GPU not connected to monitor.

GPU 1
https://prnt.sc/u1ftfd

Other GPU
https://prnt.sc/u1fuxz

GPU-Z shows that on 1st GPU 215+Mb videomemory is in use... That's why it's not enough to mine eth.

In ports of 1st GPU inserted something? If you use igpu Windows didn't use other GPU memory... Something wrong here...

nothing inserted at gpu 1 and already set igpu enable in bios.  

Don't know than what's wrong with your comp... Try to search info about your motherboard... Maybe it's need to update mobo bios...
Try to delete AMD drivers via DDU and install again.

Ok, will try again. Thanks bro 

[AzzAz]

Hi,
trying to have Phoenix working on my RXs 4GB. I'm facing 2 problems.
It's a W10 8 gpus rig, 4Gb RAM, 32GB virtual memory, drivers just updated to 20.4.2

Running more than 5 gpus gives a fatal error.
-gpus 12345 works
-gpus 23456 works
-gpus 123456 fatal error, nothing more in log

-mt 1 and -mt 2 have no effect. Gpus are bios flashed, is it for that ?

Parameters used : -mt 1 -gt 46 -gpus 12345 -amd -acm

32G is not enough. Try 42 for example...

[UselessGuru]

After all, I think that amount of rejected(stale) shares on nicehash is too much...
Effective speed 34MH/s, at pool 33MH/s.
About 3% loss...

MemClock of 2250 seems too high. Try setting '-mclock 2100' or even lower

PhoenixMiner automatically increases mem clock by +/- 200MHz (unless you set '-mclock 0' which will set and lock mem clock to the driver stock speed, in my case 2000MHz)
In both cases PhoenixMiner locks the mem clock, so it cannot be altered by external utilities, e.g MSI Afterburner

@devs: Could you please add an option to leav mem clock untouched and unlocked, so it can be controlled externally? Thank you!

[UnclWish]

After all, I think that amount of rejected(stale) shares on nicehash is too much...
Effective speed 34MH/s, at pool 33MH/s.
About 3% loss...

MemClock of 2250 seems too high. Try setting -mclock 2100 or even lower

Why? I didn't have incorrect shares or hardware errors. It's not overclock problems. I have too much "job not found" rejected shares.

[UselessGuru]

Why? I didn't have incorrect shares or hardware errors. It's not overclock problems. I have too much "job not found" rejected shares.

True - I did not read you statement properly - my card can only do mem clock of 2100, after this I get lots of bad shares.
I was just investigating this problem when posting. so my thoughts got all mixed up.

[UnclWish]

AMD released 20.8.2 driver. I checked it - PM support it. OpenCL still from 20.7.1.
So 20.8.2 can be installed without any difference with 20.7.1 drivers.

[john1010]

AMD released 20.8.2 driver. I checked it - PM support it. OpenCL still from 20.7.1.
So 20.8.2 can be installed without any difference with 20.7.1 drivers.

I tried to installed 20.8.2 with my 12 rx 4gb flashed bios but when i tried to patch with the amd patcher it says that it was too big in memory and unable to patch, for me the 20.4.2 is stable as for my experience, the last thing i need to tune up is the proper command line for my rig, because i've noticed that it frozen after lessthan an hour and before it was freezing some of my cards begin to reduce its hashrate power.

[scryptr]

ETHpillan - a new tablet to increase the hashrate on video cards from AMD and NVIDIA
Support all miners for Windows (AMD+Nvidia)
Hashrate
1080ti - 55 mh/s
2080ti - 68 mh/s
RX5700 XT - 65 mh/s

DELETED MALICIOUS LINK

Ffs ban this clowns with that pills, it's freakin scam 

 I saw some of the miners talked about this pills, anyway I stopped mining in lessthan 2 years, and I just assembled my rigs just to test and see if I am able to cope my electricity bill and at least get some descent profit that's why I am started with lvl 1 because my knowledge now is absolutely  obsolete. By the way regarding that pill, is it working for RX 500 series cards?

DO NOT REPOST THE LINK! --

This link has been repeatedly posted by multiple stolen user accounts.  The moderator is deleting the original posts as they are being reported.

Further, the malicious software has been scanned and tested in a virtual sandbox.  It is a trojan!

If you quote and repost, delete the link first, please!  The easiest thing is to just click the "report to moderator" button and send a one-line report.  This is a KNOWN malicious link, and the post will be deleted. 

Thanks!       --scryptr

[SpeedY_Hun]

How to use the commands -straps, -vmt1, -vmt2, -vmt3, and -vmr on 1080Ti? I tried -nvmem 2 and the commands still are not recognized.

The miner is not recognizing the commands when I put in the bat file

I have the same problem too :/

[xeridea]

AMD released 20.8.2 driver. I checked it - PM support it. OpenCL still from 20.7.1.
So 20.8.2 can be installed without any difference with 20.7.1 drivers.

I tried to installed 20.8.2 with my 12 rx 4gb flashed bios but when i tried to patch with the amd patcher it says that it was too big in memory and unable to patch, for me the 20.4.2 is stable as for my experience, the last thing i need to tune up is the proper command line for my rig, because i've noticed that it frozen after lessthan an hour and before it was freezing some of my cards begin to reduce its hashrate power.

Download newer version of patcher....

[xeridea]

Hi,
trying to have Phoenix working on my RXs 4GB. I'm facing 2 problems.
It's a W10 8 gpus rig, 4Gb RAM, 32GB virtual memory, drivers just updated to 20.4.2

Running more than 5 gpus gives a fatal error.
-gpus 12345 works
-gpus 23456 works
-gpus 123456 fatal error, nothing more in log

-mt 1 and -mt 2 have no effect. Gpus are bios flashed, is it for that ?

Parameters used : -mt 1 -gt 46 -gpus 12345 -amd -acm

32G is not enough. Try 42 for example...

All memory allocated on GPU needs addressed in Windows, if DAG is almost 4GB, needs 4x8GB + more for good measure...

[scryptr]

LINUX AMD 20.30 DRIVERS ARE OUT--

These are the latest, and only the second, driver release for Ubuntu 20.04 Long Term Release.  They install like butter on toast and my 5700XT cards do 53MH/s with no tuning when using PhoenixMiner 5.1c.

However, I get a lot of stales and rejects, and the clock commands and voltage commands do not work.  Compared to AMD 20.10, the drivers are fine.  I could not install 20.10, they were not designed for 20.04 LTS.  If I hacked the the install in order to squeeze the drivers in place, I got only 5-6MH/s per 5700XT.  PhoenixMiner is currently optimized for AMD 20.10.

Please tune PhoenixMiner for AMD 20.30, it is the current and best release for Ubuntu 20.04 LTS.  My 5700XT cards will do 53MH/s with half the wattage on a commercial mining OS, but I like to set a rig up from scratch.

Thanks for your work, my miners send their dues 24/7.       --scryptr

[AzzAz]

My 1st GPU not connected to monitor.

GPU 1
https://prnt.sc/u1ftfd

Other GPU
https://prnt.sc/u1fuxz

GPU-Z shows that on 1st GPU 215+Mb videomemory is in use... That's why it's not enough to mine eth.

In ports of 1st GPU inserted something? If you use igpu Windows didn't use other GPU memory... Something wrong here...

nothing inserted at gpu 1 and already set igpu enable in bios.  

Don't know than what's wrong with your comp... Try to search info about your motherboard... Maybe it's need to update mobo bios...
Try to delete AMD drivers via DDU and install again.

Ok, will try again. Thanks bro 

I think it is something due to windows updates. I solved it by updating all ( 19.03, with 365 days delay on feature updates )and reinstalling video driver ( DDU...than 20.4.2). Maybe reinstall windows if that don't help

[john1010]

I don't think if my command line was correct, I see some improvement in hashrate but my 4 ramaining cards never get the increase like other card got, Im using same brand of rx 570 4gb..

my command line:

PhoenixMiner.exe -pool asia1.ethermine.org:4444 -pool2 asia1.ethermine.org:14444 -wal 0xa465*****E6F45d49ce57E************4.john1010007 -mt 2 -amd -tt 60,55,60,55,55,60,60,60,60,60,60,60 -eres 2 -wdog 1 -proto 2 -powlim -10,-10,-10,-10,-10,-10,-10,-10,-10,-10,-10,-10 -gt 45,28,45,45,45,45,45,45,45,45,45,45 -fanmin 70,70,70,70,70,70,70,70,70,70,70,70 -rmode 1 -gpureset 1


result:

main Eth speed: 327.666 MH/s, shares: 111/0/0, time: 0:22
2020.08.19:07:33:49.251: main GPUs: 1: 27.058 MH/s (11) 2: 27.933 MH/s (2) 3: 27.895 MH/s (9) 4: 25.981 MH/s (11) 5: 25.643 MH/s ( 6: 27.895 MH/s (7) 7: 25.973 MH/s (14) 8: 27.896 MH/s (10) 9: 27.899 MH/s (12) 10: 27.897 MH/s (13) 11: 27.892 MH/s (7) 12: 27.704 MH/s (7)

[Guigs321]

I don't think if my command line was correct, I see some improvement in hashrate but my 4 ramaining cards never get the increase like other card got, Im using same brand of rx 570 4gb..

my command line:

PhoenixMiner.exe -pool asia1.ethermine.org:4444 -pool2 asia1.ethermine.org:14444 -wal 0xa465*****E6F45d49ce57E************4.john1010007 -mt 2 -amd -tt 60,55,60,55,55,60,60,60,60,60,60,60 -eres 2 -wdog 1 -proto 2 -powlim -10,-10,-10,-10,-10,-10,-10,-10,-10,-10,-10,-10 -gt 45,28,45,45,45,45,45,45,45,45,45,45 -fanmin 70,70,70,70,70,70,70,70,70,70,70,70 -rmode 1 -gpureset 1


result:

main Eth speed: 327.666 MH/s, shares: 111/0/0, time: 0:22
2020.08.19:07:33:49.251: main GPUs: 1: 27.058 MH/s (11) 2: 27.933 MH/s (2) 3: 27.895 MH/s (9) 4: 25.981 MH/s (11) 5: 25.643 MH/s ( 6: 27.895 MH/s (7) 7: 25.973 MH/s (14) 8: 27.896 MH/s (10) 9: 27.899 MH/s (12) 10: 27.897 MH/s (13) 11: 27.892 MH/s (7) 12: 27.704 MH/s (7)

You don't nedd to put 12 times the same parameter if it's the same for your 12 cards.

What are your clocks? for the same GPU I have :
 - 30,8 Mh/s  1150/2060 @875mV with 30 in REF parameter in AMDTweakXL. (Samsung Memory)
 - 29,9 Mh/s  1110/2000 @875mV with 30 in REF parameter in AMDTweakXL. (Hynix Memory)

[john1010]

I don't think if my command line was correct, I see some improvement in hashrate but my 4 ramaining cards never get the increase like other card got, Im using same brand of rx 570 4gb..

my command line:

PhoenixMiner.exe -pool asia1.ethermine.org:4444 -pool2 asia1.ethermine.org:14444 -wal 0xa465*****E6F45d49ce57E************4.john1010007 -mt 2 -amd -tt 60,55,60,55,55,60,60,60,60,60,60,60 -eres 2 -wdog 1 -proto 2 -powlim -10,-10,-10,-10,-10,-10,-10,-10,-10,-10,-10,-10 -gt 45,28,45,45,45,45,45,45,45,45,45,45 -fanmin 70,70,70,70,70,70,70,70,70,70,70,70 -rmode 1 -gpureset 1


result:

main Eth speed: 327.666 MH/s, shares: 111/0/0, time: 0:22
2020.08.19:07:33:49.251: main GPUs: 1: 27.058 MH/s (11) 2: 27.933 MH/s (2) 3: 27.895 MH/s (9) 4: 25.981 MH/s (11) 5: 25.643 MH/s ( 6: 27.895 MH/s (7) 7: 25.973 MH/s (14) 8: 27.896 MH/s (10) 9: 27.899 MH/s (12) 10: 27.897 MH/s (13) 11: 27.892 MH/s (7) 12: 27.704 MH/s (7)

You don't nedd to put 12 times the same parameter if it's the same for your 12 cards.

What are your clocks? for the same GPU I have :
 - 30,8 Mh/s  1150/2060 @875mV with 30 in REF parameter in AMDTweakXL. (Samsung Memory)
 - 29,9 Mh/s  1110/2000 @875mV with 30 in REF parameter in AMDTweakXL. (Hynix Memory)

Yeah your right but this command line seems works a little for me and my cards are different moded bios, for example 10 of them are ASUS strix and they've got same moded bios, while the other was MSI and they have also a different moded bios, that's why Im' experimenting the command line... But thanks anyway for you reply, my ASUS are elpida and i don't know what the MSI is.

[bigfootnz]

Hi, I'm having problem on one my rig with 5 GTX 1070/1070Ti and PhoenixMiner v5.1c. Rig is crashing every time while DAG file is created. On other rigs with 4 GPU I do not have problems with Rigs crashing. Also Clay is working without problem on this rig with 5GPUs. I would like to use PhoenixMiner but I do not know what is the problem. Also I've tried few nVidia drivers no difference. This Rig was off for last year and I've started back mining few days ago. Does someone have idea what could be problem with this Rig? Thanks

[astark052970]

Hi, I'm having problem on one my rig with 5 GTX 1070/1070Ti and PhoenixMiner v5.1c. Rig is crashing every time while DAG file is created. On other rigs with 4 GPU I do not have problems with Rigs crashing. Also Clay is working without problem on this rig with 5GPUs. I would like to use PhoenixMiner but I do not know what is the problem. Also I've tried few nVidia drivers no difference. This Rig was off for last year and I've started back mining few days ago. Does someone have idea what could be problem with this Rig? Thanks

Came here looking for info on this. I'm having the same issue. I'm using 5700XTs, 20.4.2 drivers, and 5.1c. Things work fine at first then it will crash when creating the DAG file. This started after switching to 5.1c. I was using 4.9c before so I'm going to go back to that for now and make sure that still works.