abg00
Jr. Member
Offline
Activity: 288
Merit: 1
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
September 21, 2021, 01:39:31 PM |
|
Hi
Suddenly @ 13:30 GMT+2 on the 22 of August, my PhoenixMiner reports error while mining ETC on 3 GB cards
GPU1: Starting up… (0) GPU1: Generating etchash light cache for epoch #223 Listening for CDM remote manager at port 3335 in read-only mode Eth: New job #7e8cde29 from eu-etc.hiveon.net:8888; diff: 5000MH Eth: New job #778ea926 from eu-etc.hiveon.net:8888; diff: 5000MH Light cache generated in 4.3 s (10.2 MB/s) GPU1: Free VRAM: 2.966 GB; used: 0.018 GB GPU1: Disabling DAG pre-allocation (not enough VRAM) GPU1: Allocating DAG for epoch #223 (2.74) GB GPU1: Allocating buffers failed with: clCreateBuffer (-61). Fatal error detected. Restarting.
As far as I knwo we are far ( 1 year ) from being at epoch so DAG file size is over 3 GB
Other miners continue to work properly ( e.g. : lolminer )
I use 5.7b but also tried with 5.4c
Any idea ?
I have the same problem, anyone found solution ? one card in system? miner card connect to monitor?
|
|
|
|
winiu
Newbie
Offline
Activity: 11
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
September 21, 2021, 02:07:33 PM |
|
Hi
Suddenly @ 13:30 GMT+2 on the 22 of August, my PhoenixMiner reports error while mining ETC on 3 GB cards
GPU1: Starting up… (0) GPU1: Generating etchash light cache for epoch #223 Listening for CDM remote manager at port 3335 in read-only mode Eth: New job #7e8cde29 from eu-etc.hiveon.net:8888; diff: 5000MH Eth: New job #778ea926 from eu-etc.hiveon.net:8888; diff: 5000MH Light cache generated in 4.3 s (10.2 MB/s) GPU1: Free VRAM: 2.966 GB; used: 0.018 GB GPU1: Disabling DAG pre-allocation (not enough VRAM) GPU1: Allocating DAG for epoch #223 (2.74) GB GPU1: Allocating buffers failed with: clCreateBuffer (-61). Fatal error detected. Restarting.
As far as I knwo we are far ( 1 year ) from being at epoch so DAG file size is over 3 GB
Other miners continue to work properly ( e.g. : lolminer )
I use 5.7b but also tried with 5.4c
Any idea ?
I have the same problem, anyone found solution ? one card in system? miner card connect to monitor? The number of cards does not matter. The same on 1 card. Two, four. Connecting the monitor also does not matter. It was working normally. It stopped working on all computers overnight. I am currently using lolminer and it works fine. But I'd rather go back to Phoenix Miner ... I just don't know how. I'm mining ETC ...
|
|
|
|
m1chael
Newbie
Offline
Activity: 6
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
September 21, 2021, 10:29:11 PM |
|
Guys when I want enable watchdog function for moments when my gpu crash, for automatical restart Phoenix miner, must I write manually into my bat file "-wdog 1" or watchdog function works automatically without any additional parametr in file?
|
|
|
|
Gpumanijak
Newbie
Offline
Activity: 18
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
September 22, 2021, 05:12:56 AM |
|
Hi
Suddenly @ 13:30 GMT+2 on the 22 of August, my PhoenixMiner reports error while mining ETC on 3 GB cards
GPU1: Starting up… (0) GPU1: Generating etchash light cache for epoch #223 Listening for CDM remote manager at port 3335 in read-only mode Eth: New job #7e8cde29 from eu-etc.hiveon.net:8888; diff: 5000MH Eth: New job #778ea926 from eu-etc.hiveon.net:8888; diff: 5000MH Light cache generated in 4.3 s (10.2 MB/s) GPU1: Free VRAM: 2.966 GB; used: 0.018 GB GPU1: Disabling DAG pre-allocation (not enough VRAM) GPU1: Allocating DAG for epoch #223 (2.74) GB GPU1: Allocating buffers failed with: clCreateBuffer (-61). Fatal error detected. Restarting.
As far as I knwo we are far ( 1 year ) from being at epoch so DAG file size is over 3 GB
Other miners continue to work properly ( e.g. : lolminer )
I use 5.7b but also tried with 5.4c
Any idea ?
I have the same problem, anyone found solution ? one card in system? miner card connect to monitor? The number of cards does not matter. The same on 1 card. Two, four. Connecting the monitor also does not matter. It was working normally. It stopped working on all computers overnight. I am currently using lolminer and it works fine. But I'd rather go back to Phoenix Miner ... I just don't know how. I'm mining ETC ... Same problem with 280x 3gb, will anyone solve this??
|
|
|
|
sleep0fox
Newbie
Offline
Activity: 2
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
September 22, 2021, 10:19:21 AM Last edit: September 23, 2021, 03:18:31 AM by sleep0fox |
|
Hi, PhoenixMiner Dev
"-rmode 2" option does not work for non-GPU errors, it works only GPU errors.
Non-GPU errors are always fixed to "restart" by default.
I want to reboot on non-GPU errors with "-rmode 2" option.
--- Non-GPU errors are Stratum error, etc.
Make sure to chain all non-GPU errors to "-rmode <n>". can fix it ?
|
|
|
|
Bagge6
Newbie
Offline
Activity: 22
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
September 23, 2021, 04:48:12 AM |
|
Hello everyone
I am using Phoenix miner but -mi doesnt work for some reason, is there a button to set mining intensity? I tried numpads + and - but it gives me text "GPU tuning is disabled only optimized kernels" or something alike In my config.cfg there is -mi 6 for example but it mines with 100% intensity still
Btw I managed to bios flash 2 cards (5700xt Gigabyte and PowerColor) from 49.7mh/s to 53.8mh/s so if anyone need help with this send me a pm
|
|
|
|
relax69
Member
![*](https://bitcointalk.org/Themes/custom1/images/star.gif)
Offline
Activity: 61
Merit: 40
|
Guys when I want enable watchdog function for moments when my gpu crash, for automatical restart Phoenix miner, must I write manually into my bat file "-wdog 1" or watchdog function works automatically without any additional parametr in file?
In the miner's directory have readme.txt file. You could find this in there: -wdog <n> Enable watchdog timer: 1 - yes, 0 - no (1 is the default). The watchdog timer checks periodically if any of the GPUs freezes and if it does, restarts the miner (see the "-rmode" command-line parameter for the restart modes)
-wdtimeout <n> Watchdog timeout (30 - 300; default 45 seconds). You can use this parameter to increase the default watchdog timeout in case it restarts the miner needlessly
-rmode <n> Selects the restart mode when a GPU crashes or freezes: :0: disabled - miner will shut down instead of restarting :1: restart with the same command line options - this is the default :2: reboot (shut down miner and execute "reboot.bat")
|
|
|
|
micdee
Newbie
Offline
Activity: 11
Merit: 3
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
September 23, 2021, 07:27:08 AM |
|
Well PM 5.7b is finally running.. with the AMD 21.1.8.1 I know I am an impatient person.. With 5.5c it was about 10-20 seconds I had to wait before I could see the openCL drivers were loaded and the rest of the config file was executed.
but waiting for 5-6 minutes to finally see that the miner is actually start to load the openCL drivers and read the rest of the config file... Is the long waiting period all have to do with the extra setting features in PM?
I understand it has something to do with the pentium (3,3Ghz) CPU I use, but from 10-20 sec to 5-6 minutes waiting is a bit much in my opinion.. Anything I can do to shorten this? without upgrading my CPU.. I also use 16Gb of RAM..
any help much appreciated.
|
|
|
|
m1chael
Newbie
Offline
Activity: 6
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
September 23, 2021, 10:50:05 AM |
|
Guys when I want enable watchdog function for moments when my gpu crash, for automatical restart Phoenix miner, must I write manually into my bat file "-wdog 1" or watchdog function works automatically without any additional parametr in file?
In the miner's directory have readme.txt file. You could find this in there: -wdog <n> Enable watchdog timer: 1 - yes, 0 - no (1 is the default). The watchdog timer checks periodically if any of the GPUs freezes and if it does, restarts the miner (see the "-rmode" command-line parameter for the restart modes)
-wdtimeout <n> Watchdog timeout (30 - 300; default 45 seconds). You can use this parameter to increase the default watchdog timeout in case it restarts the miner needlessly
-rmode <n> Selects the restart mode when a GPU crashes or freezes: :0: disabled - miner will shut down instead of restarting :1: restart with the same command line options - this is the default :2: reboot (shut down miner and execute "reboot.bat")
Thank you for info. 👍 So I added into my bat file these parametres and looks it ok: -log 0 -wdog 1 -rmode 1 -nvidia
|
|
|
|
janding
Jr. Member
Offline
Activity: 170
Merit: 6
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
September 24, 2021, 01:57:42 AM Merited by vapourminer (1) |
|
Well PM 5.7b is finally running.. with the AMD 21.1.8.1 I know I am an impatient person.. With 5.5c it was about 10-20 seconds I had to wait before I could see the openCL drivers were loaded and the rest of the config file was executed.
but waiting for 5-6 minutes to finally see that the miner is actually start to load the openCL drivers and read the rest of the config file... Is the long waiting period all have to do with the extra setting features in PM?
I understand it has something to do with the pentium (3,3Ghz) CPU I use, but from 10-20 sec to 5-6 minutes waiting is a bit much in my opinion.. Anything I can do to shorten this? without upgrading my CPU.. I also use 16Gb of RAM..
any help much appreciated
I think is something else other than the CPU processor. This is what I'm using and 5.7b comes up and runs in seconds for me. Processor Intel(R) Pentium(R) CPU G4400 @ 3.30GHz, 3312 Mhz, 2 Core(s), 2 Logical Processor(s) Also same memory 16Gb
|
|
|
|
relax69
Member
![*](https://bitcointalk.org/Themes/custom1/images/star.gif)
Offline
Activity: 61
Merit: 40
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
September 24, 2021, 04:23:47 AM |
|
Well PM 5.7b is finally running.. with the AMD 21.1.8.1 I know I am an impatient person.. With 5.5c it was about 10-20 seconds I had to wait before I could see the openCL drivers were loaded and the rest of the config file was executed.
but waiting for 5-6 minutes to finally see that the miner is actually start to load the openCL drivers and read the rest of the config file... Is the long waiting period all have to do with the extra setting features in PM?
I understand it has something to do with the pentium (3,3Ghz) CPU I use, but from 10-20 sec to 5-6 minutes waiting is a bit much in my opinion.. Anything I can do to shorten this? without upgrading my CPU.. I also use 16Gb of RAM..
any help much appreciated.
Most likely is nothing to do with the CPU or with the PM software. I had same issue after I try to find best drivers for me they did huge mess in the registry. Best way to fix this is to do system restore to the point when the Windows was just installed or to do fresh install. Please note in this case you will lost all your files so do backup before instalation. Another option to speed up could be to uninstall drivers and clean up registry manualy, but I would not recomend it because will speed up but not to the point of fresh installation. Also you could gain little speed if you use hard disk, by replacing it with SSD.
|
|
|
|
swogerino
Legendary
Online
Activity: 3262
Merit: 1244
Play Poker on Telegram
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
September 24, 2021, 06:42:51 AM |
|
Well PM 5.7b is finally running.. with the AMD 21.1.8.1 I know I am an impatient person.. With 5.5c it was about 10-20 seconds I had to wait before I could see the openCL drivers were loaded and the rest of the config file was executed.
but waiting for 5-6 minutes to finally see that the miner is actually start to load the openCL drivers and read the rest of the config file... Is the long waiting period all have to do with the extra setting features in PM?
I understand it has something to do with the pentium (3,3Ghz) CPU I use, but from 10-20 sec to 5-6 minutes waiting is a bit much in my opinion.. Anything I can do to shorten this? without upgrading my CPU.. I also use 16Gb of RAM..
any help much appreciated
I think is something else other than the CPU processor. This is what I'm using and 5.7b comes up and runs in seconds for me. Processor Intel(R) Pentium(R) CPU G4400 @ 3.30GHz, 3312 Mhz, 2 Core(s), 2 Logical Processor(s) Also same memory 16Gb I have even a slower processor that I use which is G3900 Celeron which is the lowest of Gen 6 processors and it works perfectly well with the Rx 6800 XT cards I have.The processor is ruled out here and I think you need to uninstall drivers and reinstall them once again,installing a new version of driver like 21.8.1 over an old one does not always run smoothly so this is the first thing to check.Also the HDD is not a problem as the difference between an SSD and an HDD is big enough but surely not 6 minutes.
|
|
|
|
dazmann
Jr. Member
Offline
Activity: 45
Merit: 6
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
September 24, 2021, 02:58:42 PM |
|
Well PM 5.7b is finally running.. with the AMD 21.1.8.1 I know I am an impatient person.. With 5.5c it was about 10-20 seconds I had to wait before I could see the openCL drivers were loaded and the rest of the config file was executed.
but waiting for 5-6 minutes to finally see that the miner is actually start to load the openCL drivers and read the rest of the config file... Is the long waiting period all have to do with the extra setting features in PM?
I understand it has something to do with the pentium (3,3Ghz) CPU I use, but from 10-20 sec to 5-6 minutes waiting is a bit much in my opinion.. Anything I can do to shorten this? without upgrading my CPU.. I also use 16Gb of RAM..
any help much appreciated.
Your HDD or SSD might be the culprit. Check the S.M.A.R.T. Try a chkdsk to check for errors or try a defrag. If not, try doing a clean installation of the GPU drivers using DDU (Display Driver Uninstaller) and download the full driver version from the release notes page, do not use the updater/downloader.
|
|
|
|
|
oleg_123
Newbie
Offline
Activity: 2
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
September 24, 2021, 07:17:04 PM |
|
Hi
Suddenly @ 13:30 GMT+2 on the 22 of August, my PhoenixMiner reports error while mining ETC on 3 GB cards
GPU1: Starting up… (0) GPU1: Generating etchash light cache for epoch #223 Listening for CDM remote manager at port 3335 in read-only mode Eth: New job #7e8cde29 from eu-etc.hiveon.net:8888; diff: 5000MH Eth: New job #778ea926 from eu-etc.hiveon.net:8888; diff: 5000MH Light cache generated in 4.3 s (10.2 MB/s) GPU1: Free VRAM: 2.966 GB; used: 0.018 GB GPU1: Disabling DAG pre-allocation (not enough VRAM) GPU1: Allocating DAG for epoch #223 (2.74) GB GPU1: Allocating buffers failed with: clCreateBuffer (-61). Fatal error detected. Restarting.
As far as I knwo we are far ( 1 year ) from being at epoch so DAG file size is over 3 GB
Other miners continue to work properly ( e.g. : lolminer )
I use 5.7b but also tried with 5.4c
Any idea ?
I have the same problem, anyone found solution ? one card in system? miner card connect to monitor? The number of cards does not matter. The same on 1 card. Two, four. Connecting the monitor also does not matter. It was working normally. It stopped working on all computers overnight. I am currently using lolminer and it works fine. But I'd rather go back to Phoenix Miner ... I just don't know how. I'm mining ETC ... Same problem with 280x 3gb, will anyone solve this?? Hello, The same problem here with r9 280/280x. Is there any solution?
|
|
|
|
janding
Jr. Member
Offline
Activity: 170
Merit: 6
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
September 25, 2021, 02:57:17 AM |
|
Hi
Suddenly @ 13:30 GMT+2 on the 22 of August, my PhoenixMiner reports error while mining ETC on 3 GB cards
GPU1: Starting up… (0) GPU1: Generating etchash light cache for epoch #223 Listening for CDM remote manager at port 3335 in read-only mode Eth: New job #7e8cde29 from eu-etc.hiveon.net:8888; diff: 5000MH Eth: New job #778ea926 from eu-etc.hiveon.net:8888; diff: 5000MH Light cache generated in 4.3 s (10.2 MB/s) GPU1: Free VRAM: 2.966 GB; used: 0.018 GB GPU1: Disabling DAG pre-allocation (not enough VRAM) GPU1: Allocating DAG for epoch #223 (2.74) GB GPU1: Allocating buffers failed with: clCreateBuffer (-61). Fatal error detected. Restarting.
As far as I knwo we are far ( 1 year ) from being at epoch so DAG file size is over 3 GB
Other miners continue to work properly ( e.g. : lolminer )
I use 5.7b but also tried with 5.4c
Any idea ?
I have the same problem, anyone found solution ? one card in system? miner card connect to monitor? The number of cards does not matter. The same on 1 card. Two, four. Connecting the monitor also does not matter. It was working normally. It stopped working on all computers overnight. I am currently using lolminer and it works fine. But I'd rather go back to Phoenix Miner ... I just don't know how. I'm mining ETC ... Same problem with 280x 3gb, will anyone solve this?? Hello, The same problem here with r9 280/280x. Is there any solution? I'm going to assume that you have done this ? -rvram -1 If not, then do that.
|
|
|
|
relax69
Member
![*](https://bitcointalk.org/Themes/custom1/images/star.gif)
Offline
Activity: 61
Merit: 40
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
September 25, 2021, 03:36:32 AM |
|
Hello anyone can help me for thats problem. Its my first try on windows 10 Pro 64 ![](https://ip.bitcointalk.org/?u=https%3A%2F%2Fi.ibb.co%2FB2zBMWD%2Ferror-phoenix-start.jpg&t=665&c=KNGwamiRYwsQzw) best regards Zombie mode for mining ETH with 4G cards stopped working more than 6 months ago. Try mining ETC or other coins.
|
|
|
|
list1999
Newbie
Offline
Activity: 1
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
September 25, 2021, 06:18:26 PM |
|
Hi
Suddenly @ 13:30 GMT+2 on the 22 of August, my PhoenixMiner reports error while mining ETC on 3 GB cards
GPU1: Starting up… (0) GPU1: Generating etchash light cache for epoch #223 Listening for CDM remote manager at port 3335 in read-only mode Eth: New job #7e8cde29 from eu-etc.hiveon.net:8888; diff: 5000MH Eth: New job #778ea926 from eu-etc.hiveon.net:8888; diff: 5000MH Light cache generated in 4.3 s (10.2 MB/s) GPU1: Free VRAM: 2.966 GB; used: 0.018 GB GPU1: Disabling DAG pre-allocation (not enough VRAM) GPU1: Allocating DAG for epoch #223 (2.74) GB GPU1: Allocating buffers failed with: clCreateBuffer (-61). Fatal error detected. Restarting.
As far as I knwo we are far ( 1 year ) from being at epoch so DAG file size is over 3 GB
Other miners continue to work properly ( e.g. : lolminer )
I use 5.7b but also tried with 5.4c
Any idea ?
I have the same problem, anyone found solution ? one card in system? miner card connect to monitor? The number of cards does not matter. The same on 1 card. Two, four. Connecting the monitor also does not matter. It was working normally. It stopped working on all computers overnight. I am currently using lolminer and it works fine. But I'd rather go back to Phoenix Miner ... I just don't know how. I'm mining ETC ... Same problem with 280x 3gb, will anyone solve this?? Hello, The same problem here with r9 280/280x. Is there any solution? I'm going to assume that you have done this ? -rvram -1 If not, then do that. There is only one solution to the problem so far - lolminer. hd7950 3Gb - 9,8 mh/s etc
|
|
|
|
iStarbuck
Newbie
Offline
Activity: 1
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
September 25, 2021, 08:29:04 PM |
|
Does PhoenixMiner have any planned implementations of the LHR workarounds like NBminer has implemented that restores up to 70% of hashing power for ETH? I've been using PheonixMiner exclusively and though I've tried a few out I keep coming back, but even though my new LHR 3080 is pulling way more than my 1080 that I replaced in my main gaming rig, it hurts knowing that there's potentially so much performance left on the table when compared to NBminer. I've toyed with it but haven't gotten it to work so for time and sanity I'm keeping up with the 50% hash and what I know best.
|
|
|
|
oleg_123
Newbie
Offline
Activity: 2
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
September 26, 2021, 08:44:06 AM |
|
Hi
Suddenly @ 13:30 GMT+2 on the 22 of August, my PhoenixMiner reports error while mining ETC on 3 GB cards
GPU1: Starting up… (0) GPU1: Generating etchash light cache for epoch #223 Listening for CDM remote manager at port 3335 in read-only mode Eth: New job #7e8cde29 from eu-etc.hiveon.net:8888; diff: 5000MH Eth: New job #778ea926 from eu-etc.hiveon.net:8888; diff: 5000MH Light cache generated in 4.3 s (10.2 MB/s) GPU1: Free VRAM: 2.966 GB; used: 0.018 GB GPU1: Disabling DAG pre-allocation (not enough VRAM) GPU1: Allocating DAG for epoch #223 (2.74) GB GPU1: Allocating buffers failed with: clCreateBuffer (-61). Fatal error detected. Restarting.
As far as I knwo we are far ( 1 year ) from being at epoch so DAG file size is over 3 GB
Other miners continue to work properly ( e.g. : lolminer )
I use 5.7b but also tried with 5.4c
Any idea ?
I have the same problem, anyone found solution ? one card in system? miner card connect to monitor? The number of cards does not matter. The same on 1 card. Two, four. Connecting the monitor also does not matter. It was working normally. It stopped working on all computers overnight. I am currently using lolminer and it works fine. But I'd rather go back to Phoenix Miner ... I just don't know how. I'm mining ETC ... Same problem with 280x 3gb, will anyone solve this?? Hello, The same problem here with r9 280/280x. Is there any solution? I'm going to assume that you have done this ? -rvram -1 If not, then do that. There is only one solution to the problem so far - lolminer. hd7950 3Gb - 9,8 mh/s etc "-rvram -1" doesn't help. The error is still the same.
|
|
|
|
|