Bitcoin Forum
March 28, 2024, 08:12:37 PM *
News: Latest Bitcoin Core release: 26.0 [Torrent]
 
   Home   Help Search Login Register More  
Pages: « 1 ... 414 415 416 417 418 419 420 421 422 423 424 425 426 427 428 429 430 431 432 433 434 435 436 437 438 439 440 441 442 443 444 445 446 447 448 449 450 451 452 453 454 455 456 457 458 459 460 461 462 463 [464] 465 466 467 468 469 470 471 472 473 474 475 476 477 478 479 480 481 482 483 484 485 486 487 488 489 490 491 492 493 494 495 496 497 498 499 »
  Print  
Author Topic: PhoenixMiner 6.2c: fastest Ethereum/Ethash miner with lowest devfee (Win/Linux)  (Read 784583 times)
abg00
Jr. Member
*
Offline Offline

Activity: 288
Merit: 1


View Profile
September 21, 2021, 01:39:31 PM
 #9261

Hi

Suddenly @ 13:30 GMT+2 on the 22 of August, my PhoenixMiner reports error while mining ETC on 3 GB cards

GPU1: Starting up… (0)
GPU1: Generating etchash light cache for epoch #223
Listening for CDM remote manager at port 3335 in read-only mode
Eth: New job #7e8cde29 from eu-etc.hiveon.net:8888; diff: 5000MH
Eth: New job #778ea926 from eu-etc.hiveon.net:8888; diff: 5000MH
Light cache generated in 4.3 s (10.2 MB/s)
GPU1: Free VRAM: 2.966 GB; used: 0.018 GB
GPU1: Disabling DAG pre-allocation (not enough VRAM)
GPU1: Allocating DAG for epoch #223 (2.74) GB
GPU1: Allocating buffers failed with: clCreateBuffer (-61).

Fatal error detected. Restarting.


As far as I knwo we are far ( 1 year ) from being at epoch so DAG file size is over 3 GB

Other miners continue to work properly ( e.g. : lolminer )

I use 5.7b but also tried with 5.4c

Any idea ?

I have the same problem, anyone found solution ?

one card in system? miner card connect to monitor?
1711656757
Hero Member
*
Offline Offline

Posts: 1711656757

View Profile Personal Message (Offline)

Ignore
1711656757
Reply with quote  #2

1711656757
Report to moderator
1711656757
Hero Member
*
Offline Offline

Posts: 1711656757

View Profile Personal Message (Offline)

Ignore
1711656757
Reply with quote  #2

1711656757
Report to moderator
If you see garbage posts (off-topic, trolling, spam, no point, etc.), use the "report to moderator" links. All reports are investigated, though you will rarely be contacted about your reports.
Advertised sites are not endorsed by the Bitcoin Forum. They may be unsafe, untrustworthy, or illegal in your jurisdiction.
winiu
Newbie
*
Offline Offline

Activity: 11
Merit: 0


View Profile
September 21, 2021, 02:07:33 PM
 #9262

Hi

Suddenly @ 13:30 GMT+2 on the 22 of August, my PhoenixMiner reports error while mining ETC on 3 GB cards

GPU1: Starting up… (0)
GPU1: Generating etchash light cache for epoch #223
Listening for CDM remote manager at port 3335 in read-only mode
Eth: New job #7e8cde29 from eu-etc.hiveon.net:8888; diff: 5000MH
Eth: New job #778ea926 from eu-etc.hiveon.net:8888; diff: 5000MH
Light cache generated in 4.3 s (10.2 MB/s)
GPU1: Free VRAM: 2.966 GB; used: 0.018 GB
GPU1: Disabling DAG pre-allocation (not enough VRAM)
GPU1: Allocating DAG for epoch #223 (2.74) GB
GPU1: Allocating buffers failed with: clCreateBuffer (-61).

Fatal error detected. Restarting.


As far as I knwo we are far ( 1 year ) from being at epoch so DAG file size is over 3 GB

Other miners continue to work properly ( e.g. : lolminer )

I use 5.7b but also tried with 5.4c

Any idea ?

I have the same problem, anyone found solution ?

one card in system? miner card connect to monitor?

The number of cards does not matter. The same on 1 card. Two, four. Connecting the monitor also does not matter. It was working normally. It stopped working on all computers overnight. I am currently using lolminer and it works fine. But I'd rather go back to Phoenix Miner ... I just don't know how.

I'm mining ETC ...
m1chael
Newbie
*
Offline Offline

Activity: 6
Merit: 0


View Profile
September 21, 2021, 10:29:11 PM
 #9263

Guys when I want enable watchdog function for moments when my gpu crash, for automatical restart Phoenix miner, must I write manually into my bat file "-wdog 1" or watchdog function works automatically without any additional parametr in file?
Gpumanijak
Newbie
*
Offline Offline

Activity: 18
Merit: 0


View Profile
September 22, 2021, 05:12:56 AM
 #9264

Hi

Suddenly @ 13:30 GMT+2 on the 22 of August, my PhoenixMiner reports error while mining ETC on 3 GB cards

GPU1: Starting up… (0)
GPU1: Generating etchash light cache for epoch #223
Listening for CDM remote manager at port 3335 in read-only mode
Eth: New job #7e8cde29 from eu-etc.hiveon.net:8888; diff: 5000MH
Eth: New job #778ea926 from eu-etc.hiveon.net:8888; diff: 5000MH
Light cache generated in 4.3 s (10.2 MB/s)
GPU1: Free VRAM: 2.966 GB; used: 0.018 GB
GPU1: Disabling DAG pre-allocation (not enough VRAM)
GPU1: Allocating DAG for epoch #223 (2.74) GB
GPU1: Allocating buffers failed with: clCreateBuffer (-61).

Fatal error detected. Restarting.


As far as I knwo we are far ( 1 year ) from being at epoch so DAG file size is over 3 GB

Other miners continue to work properly ( e.g. : lolminer )

I use 5.7b but also tried with 5.4c

Any idea ?

I have the same problem, anyone found solution ?

one card in system? miner card connect to monitor?

The number of cards does not matter. The same on 1 card. Two, four. Connecting the monitor also does not matter. It was working normally. It stopped working on all computers overnight. I am currently using lolminer and it works fine. But I'd rather go back to Phoenix Miner ... I just don't know how.

I'm mining ETC ...


Same problem with 280x 3gb, will anyone solve this??
sleep0fox
Newbie
*
Offline Offline

Activity: 2
Merit: 0


View Profile
September 22, 2021, 10:19:21 AM
Last edit: September 23, 2021, 03:18:31 AM by sleep0fox
 #9265

Hi, PhoenixMiner Dev

"-rmode 2" option does not work for non-GPU errors, it works only GPU errors.

Non-GPU errors are always fixed to "restart" by default.

I want to reboot on non-GPU errors with "-rmode 2" option.

--- Non-GPU errors are Stratum error, etc.


Make sure to chain all non-GPU errors to "-rmode <n>".
can fix it ?
Bagge6
Newbie
*
Offline Offline

Activity: 22
Merit: 0


View Profile
September 23, 2021, 04:48:12 AM
 #9266

Hello everyone

I am using Phoenix miner but -mi doesnt work for some reason, is there a button to set mining intensity? I tried numpads + and - but it gives me text "GPU tuning is disabled only optimized kernels" or something alike
In my config.cfg there is -mi 6 for example but it mines with 100% intensity still

Btw I managed to bios flash 2 cards (5700xt Gigabyte and PowerColor) from 49.7mh/s to 53.8mh/s so if anyone need help with this send me a pm
relax69
Member
**
Offline Offline

Activity: 61
Merit: 40


View Profile
September 23, 2021, 04:56:00 AM
Merited by vapourminer (2), xandry (2)
 #9267

Guys when I want enable watchdog function for moments when my gpu crash, for automatical restart Phoenix miner, must I write manually into my bat file "-wdog 1" or watchdog function works automatically without any additional parametr in file?

In the miner's directory have readme.txt file. You could find this in there:

Code:
-wdog <n>
   Enable watchdog timer: 1 - yes, 0 - no (1 is the default). The
   watchdog timer checks periodically if any of the GPUs freezes and
   if it does, restarts the miner (see the "-rmode" command-line
   parameter for the restart modes)

-wdtimeout <n>
   Watchdog timeout (30 - 300; default 45 seconds). You can use this
   parameter to increase the default watchdog timeout in case it
   restarts the miner needlessly

-rmode <n>
   Selects the restart mode when a GPU crashes or freezes: :0:
   disabled - miner will shut down instead of restarting :1: restart
   with the same command line options - this is the default :2: reboot
   (shut down miner and execute "reboot.bat")

micdee
Newbie
*
Offline Offline

Activity: 11
Merit: 3


View Profile
September 23, 2021, 07:27:08 AM
 #9268

Well PM 5.7b is finally running.. with the AMD 21.1.8.1
I know I am an impatient person..
With 5.5c it was about 10-20 seconds I had to wait before I could see the openCL drivers were loaded and the rest of the config file was executed.

but waiting for 5-6 minutes to finally see that the miner is actually start to load the openCL drivers and read the rest of the config file...
Is the long waiting period all have to do with the extra setting features in PM?

I understand it has something to do with the pentium (3,3Ghz) CPU I use, but from 10-20 sec to 5-6 minutes waiting is a bit much in my opinion.. Anything I can do to shorten this? without upgrading my CPU..
I also use 16Gb of RAM..

any help much appreciated.

m1chael
Newbie
*
Offline Offline

Activity: 6
Merit: 0


View Profile
September 23, 2021, 10:50:05 AM
 #9269

Guys when I want enable watchdog function for moments when my gpu crash, for automatical restart Phoenix miner, must I write manually into my bat file "-wdog 1" or watchdog function works automatically without any additional parametr in file?

In the miner's directory have readme.txt file. You could find this in there:

Code:
-wdog <n>
   Enable watchdog timer: 1 - yes, 0 - no (1 is the default). The
   watchdog timer checks periodically if any of the GPUs freezes and
   if it does, restarts the miner (see the "-rmode" command-line
   parameter for the restart modes)

-wdtimeout <n>
   Watchdog timeout (30 - 300; default 45 seconds). You can use this
   parameter to increase the default watchdog timeout in case it
   restarts the miner needlessly

-rmode <n>
   Selects the restart mode when a GPU crashes or freezes: :0:
   disabled - miner will shut down instead of restarting :1: restart
   with the same command line options - this is the default :2: reboot
   (shut down miner and execute "reboot.bat")


Thank you for info. 👍
So I added into my bat file these parametres and looks it ok:  -log 0 -wdog 1 -rmode 1 -nvidia
janding
Jr. Member
*
Offline Offline

Activity: 170
Merit: 6


View Profile
September 24, 2021, 01:57:42 AM
Merited by vapourminer (1)
 #9270

Well PM 5.7b is finally running.. with the AMD 21.1.8.1
I know I am an impatient person..
With 5.5c it was about 10-20 seconds I had to wait before I could see the openCL drivers were loaded and the rest of the config file was executed.

but waiting for 5-6 minutes to finally see that the miner is actually start to load the openCL drivers and read the rest of the config file...
Is the long waiting period all have to do with the extra setting features in PM?

I understand it has something to do with the pentium (3,3Ghz) CPU I use, but from 10-20 sec to 5-6 minutes waiting is a bit much in my opinion.. Anything I can do to shorten this? without upgrading my CPU..
I also use 16Gb of RAM..

any help much appreciated


I think is something else other than the CPU processor.
This is what I'm using and 5.7b comes up and runs in seconds for me.

Processor   Intel(R) Pentium(R) CPU G4400 @ 3.30GHz, 3312 Mhz, 2 Core(s), 2 Logical Processor(s)
Also same memory 16Gb
relax69
Member
**
Offline Offline

Activity: 61
Merit: 40


View Profile
September 24, 2021, 04:23:47 AM
 #9271

Well PM 5.7b is finally running.. with the AMD 21.1.8.1
I know I am an impatient person..
With 5.5c it was about 10-20 seconds I had to wait before I could see the openCL drivers were loaded and the rest of the config file was executed.

but waiting for 5-6 minutes to finally see that the miner is actually start to load the openCL drivers and read the rest of the config file...
Is the long waiting period all have to do with the extra setting features in PM?

I understand it has something to do with the pentium (3,3Ghz) CPU I use, but from 10-20 sec to 5-6 minutes waiting is a bit much in my opinion.. Anything I can do to shorten this? without upgrading my CPU..
I also use 16Gb of RAM..

any help much appreciated.



Most likely is nothing to do with the CPU or with the PM software. I had same issue after I try to find best drivers for me they did huge mess in the registry.

Best way to fix this is to do system restore to the point when the Windows was just installed or to do fresh install. Please note in this case you will lost all your files so do backup before instalation.
Another option to speed up could be to uninstall drivers and clean up registry manualy, but I would not recomend it because will speed up but not to the point of fresh installation.

Also you could gain little speed if you use hard disk, by replacing it with SSD.
swogerino
Legendary
*
Offline Offline

Activity: 3108
Merit: 1230


Leading Crypto Sports Betting & Casino Platform


View Profile
September 24, 2021, 06:42:51 AM
 #9272

Well PM 5.7b is finally running.. with the AMD 21.1.8.1
I know I am an impatient person..
With 5.5c it was about 10-20 seconds I had to wait before I could see the openCL drivers were loaded and the rest of the config file was executed.

but waiting for 5-6 minutes to finally see that the miner is actually start to load the openCL drivers and read the rest of the config file...
Is the long waiting period all have to do with the extra setting features in PM?

I understand it has something to do with the pentium (3,3Ghz) CPU I use, but from 10-20 sec to 5-6 minutes waiting is a bit much in my opinion.. Anything I can do to shorten this? without upgrading my CPU..
I also use 16Gb of RAM..

any help much appreciated


I think is something else other than the CPU processor.
This is what I'm using and 5.7b comes up and runs in seconds for me.

Processor   Intel(R) Pentium(R) CPU G4400 @ 3.30GHz, 3312 Mhz, 2 Core(s), 2 Logical Processor(s)
Also same memory 16Gb


I have even a slower processor that I use which is G3900 Celeron which is the lowest of Gen 6 processors and it works perfectly well with the Rx 6800 XT cards I have.The processor is ruled out here and I think you need to uninstall drivers and reinstall them once again,installing a new version of driver like 21.8.1 over an old one does not always run smoothly so this is the first thing to check.Also the HDD is not a problem as the difference between an SSD and an HDD is big enough but surely not 6 minutes.

..Stake.com..   ▄████████████████████████████████████▄
   ██ ▄▄▄▄▄▄▄▄▄▄            ▄▄▄▄▄▄▄▄▄▄ ██  ▄████▄
   ██ ▀▀▀▀▀▀▀▀▀▀ ██████████ ▀▀▀▀▀▀▀▀▀▀ ██  ██████
   ██ ██████████ ██      ██ ██████████ ██   ▀██▀
   ██ ██      ██ ██████  ██ ██      ██ ██    ██
   ██ ██████  ██ █████  ███ ██████  ██ ████▄ ██
   ██ █████  ███ ████  ████ █████  ███ ████████
   ██ ████  ████ ██████████ ████  ████ ████▀
   ██ ██████████ ▄▄▄▄▄▄▄▄▄▄ ██████████ ██
   ██            ▀▀▀▀▀▀▀▀▀▀            ██ 
   ▀█████████▀ ▄████████████▄ ▀█████████▀
  ▄▄▄▄▄▄▄▄▄▄▄▄███  ██  ██  ███▄▄▄▄▄▄▄▄▄▄▄▄
 ██████████████████████████████████████████
▄▀▀▀▀▀▀▀▀▀▀▀▀▀▀▀▀▀▀▄
█  ▄▀▄             █▀▀█▀▄▄
█  █▀█             █  ▐  ▐▌
█       ▄██▄       █  ▌  █
█     ▄██████▄     █  ▌ ▐▌
█    ██████████    █ ▐  █
█   ▐██████████▌   █ ▐ ▐▌
█    ▀▀██████▀▀    █ ▌ █
█     ▄▄▄██▄▄▄     █ ▌▐▌
█                  █▐ █
█                  █▐▐▌
█                  █▐█
▀▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▄▀█
▄▄█████████▄▄
▄██▀▀▀▀█████▀▀▀▀██▄
▄█▀       ▐█▌       ▀█▄
██         ▐█▌         ██
████▄     ▄█████▄     ▄████
████████▄███████████▄████████
███▀    █████████████    ▀███
██       ███████████       ██
▀█▄       █████████       ▄█▀
▀█▄    ▄██▀▀▀▀▀▀▀██▄  ▄▄▄█▀
▀███████         ███████▀
▀█████▄       ▄█████▀
▀▀▀███▄▄▄███▀▀▀
..PLAY NOW..
dazmann
Jr. Member
*
Offline Offline

Activity: 45
Merit: 6


View Profile
September 24, 2021, 02:58:42 PM
 #9273

Well PM 5.7b is finally running.. with the AMD 21.1.8.1
I know I am an impatient person..
With 5.5c it was about 10-20 seconds I had to wait before I could see the openCL drivers were loaded and the rest of the config file was executed.

but waiting for 5-6 minutes to finally see that the miner is actually start to load the openCL drivers and read the rest of the config file...
Is the long waiting period all have to do with the extra setting features in PM?

I understand it has something to do with the pentium (3,3Ghz) CPU I use, but from 10-20 sec to 5-6 minutes waiting is a bit much in my opinion.. Anything I can do to shorten this? without upgrading my CPU..
I also use 16Gb of RAM..

any help much appreciated.


Your HDD or SSD might be the culprit. Check the S.M.A.R.T. Try a chkdsk to check for errors or try a defrag. If not, try doing a clean installation of the GPU drivers using DDU (Display Driver Uninstaller) and download the full driver version from the release notes page, do not use the updater/downloader.
Jonasuke
Newbie
*
Offline Offline

Activity: 7
Merit: 0


View Profile
September 24, 2021, 06:05:21 PM
 #9274

Hello anyone can help me for thats problem.
Its my first try on windows 10 Pro 64

https://i.ibb.co/B2zBMWD/error-phoenix-start.jpg

best regards
oleg_123
Newbie
*
Offline Offline

Activity: 2
Merit: 0


View Profile
September 24, 2021, 07:17:04 PM
 #9275

Hi

Suddenly @ 13:30 GMT+2 on the 22 of August, my PhoenixMiner reports error while mining ETC on 3 GB cards

GPU1: Starting up… (0)
GPU1: Generating etchash light cache for epoch #223
Listening for CDM remote manager at port 3335 in read-only mode
Eth: New job #7e8cde29 from eu-etc.hiveon.net:8888; diff: 5000MH
Eth: New job #778ea926 from eu-etc.hiveon.net:8888; diff: 5000MH
Light cache generated in 4.3 s (10.2 MB/s)
GPU1: Free VRAM: 2.966 GB; used: 0.018 GB
GPU1: Disabling DAG pre-allocation (not enough VRAM)
GPU1: Allocating DAG for epoch #223 (2.74) GB
GPU1: Allocating buffers failed with: clCreateBuffer (-61).

Fatal error detected. Restarting.


As far as I knwo we are far ( 1 year ) from being at epoch so DAG file size is over 3 GB

Other miners continue to work properly ( e.g. : lolminer )

I use 5.7b but also tried with 5.4c

Any idea ?

I have the same problem, anyone found solution ?

one card in system? miner card connect to monitor?

The number of cards does not matter. The same on 1 card. Two, four. Connecting the monitor also does not matter. It was working normally. It stopped working on all computers overnight. I am currently using lolminer and it works fine. But I'd rather go back to Phoenix Miner ... I just don't know how.

I'm mining ETC ...


Same problem with 280x 3gb, will anyone solve this??

Hello,
The same problem here with r9 280/280x. Is there any solution?
janding
Jr. Member
*
Offline Offline

Activity: 170
Merit: 6


View Profile
September 25, 2021, 02:57:17 AM
 #9276

Hi

Suddenly @ 13:30 GMT+2 on the 22 of August, my PhoenixMiner reports error while mining ETC on 3 GB cards

GPU1: Starting up… (0)
GPU1: Generating etchash light cache for epoch #223
Listening for CDM remote manager at port 3335 in read-only mode
Eth: New job #7e8cde29 from eu-etc.hiveon.net:8888; diff: 5000MH
Eth: New job #778ea926 from eu-etc.hiveon.net:8888; diff: 5000MH
Light cache generated in 4.3 s (10.2 MB/s)
GPU1: Free VRAM: 2.966 GB; used: 0.018 GB
GPU1: Disabling DAG pre-allocation (not enough VRAM)
GPU1: Allocating DAG for epoch #223 (2.74) GB
GPU1: Allocating buffers failed with: clCreateBuffer (-61).

Fatal error detected. Restarting.


As far as I knwo we are far ( 1 year ) from being at epoch so DAG file size is over 3 GB

Other miners continue to work properly ( e.g. : lolminer )

I use 5.7b but also tried with 5.4c

Any idea ?

I have the same problem, anyone found solution ?

one card in system? miner card connect to monitor?

The number of cards does not matter. The same on 1 card. Two, four. Connecting the monitor also does not matter. It was working normally. It stopped working on all computers overnight. I am currently using lolminer and it works fine. But I'd rather go back to Phoenix Miner ... I just don't know how.

I'm mining ETC ...


Same problem with 280x 3gb, will anyone solve this??

Hello,
The same problem here with r9 280/280x. Is there any solution?

I'm going to assume that you have done this ?

 -rvram  -1

If not, then do that.
relax69
Member
**
Offline Offline

Activity: 61
Merit: 40


View Profile
September 25, 2021, 03:36:32 AM
 #9277

Hello anyone can help me for thats problem.
Its my first try on windows 10 Pro 64



best regards

Zombie mode for mining ETH with 4G cards stopped working more than 6 months ago. Try mining ETC or other coins.
list1999
Newbie
*
Offline Offline

Activity: 1
Merit: 0


View Profile
September 25, 2021, 06:18:26 PM
 #9278

Hi

Suddenly @ 13:30 GMT+2 on the 22 of August, my PhoenixMiner reports error while mining ETC on 3 GB cards

GPU1: Starting up… (0)
GPU1: Generating etchash light cache for epoch #223
Listening for CDM remote manager at port 3335 in read-only mode
Eth: New job #7e8cde29 from eu-etc.hiveon.net:8888; diff: 5000MH
Eth: New job #778ea926 from eu-etc.hiveon.net:8888; diff: 5000MH
Light cache generated in 4.3 s (10.2 MB/s)
GPU1: Free VRAM: 2.966 GB; used: 0.018 GB
GPU1: Disabling DAG pre-allocation (not enough VRAM)
GPU1: Allocating DAG for epoch #223 (2.74) GB
GPU1: Allocating buffers failed with: clCreateBuffer (-61).

Fatal error detected. Restarting.


As far as I knwo we are far ( 1 year ) from being at epoch so DAG file size is over 3 GB

Other miners continue to work properly ( e.g. : lolminer )

I use 5.7b but also tried with 5.4c

Any idea ?

I have the same problem, anyone found solution ?

one card in system? miner card connect to monitor?

The number of cards does not matter. The same on 1 card. Two, four. Connecting the monitor also does not matter. It was working normally. It stopped working on all computers overnight. I am currently using lolminer and it works fine. But I'd rather go back to Phoenix Miner ... I just don't know how.

I'm mining ETC ...


Same problem with 280x 3gb, will anyone solve this??

Hello,
The same problem here with r9 280/280x. Is there any solution?

I'm going to assume that you have done this ?

 -rvram  -1

If not, then do that.


There is only one solution to the problem so far - lolminer. hd7950 3Gb - 9,8 mh/s etc
iStarbuck
Newbie
*
Offline Offline

Activity: 1
Merit: 0


View Profile
September 25, 2021, 08:29:04 PM
 #9279

Does PhoenixMiner have any planned implementations of the LHR workarounds like NBminer has implemented that restores up to 70% of hashing power for ETH? I've been using PheonixMiner exclusively and though I've tried a few out I keep coming back, but even though my new LHR 3080 is pulling way more than my 1080 that I replaced in my main gaming rig, it hurts knowing that there's potentially so much performance left on the table when compared to NBminer. I've toyed with it but haven't gotten it to work so for time and sanity I'm keeping up with the 50% hash and what I know best.
oleg_123
Newbie
*
Offline Offline

Activity: 2
Merit: 0


View Profile
September 26, 2021, 08:44:06 AM
 #9280

Hi

Suddenly @ 13:30 GMT+2 on the 22 of August, my PhoenixMiner reports error while mining ETC on 3 GB cards

GPU1: Starting up… (0)
GPU1: Generating etchash light cache for epoch #223
Listening for CDM remote manager at port 3335 in read-only mode
Eth: New job #7e8cde29 from eu-etc.hiveon.net:8888; diff: 5000MH
Eth: New job #778ea926 from eu-etc.hiveon.net:8888; diff: 5000MH
Light cache generated in 4.3 s (10.2 MB/s)
GPU1: Free VRAM: 2.966 GB; used: 0.018 GB
GPU1: Disabling DAG pre-allocation (not enough VRAM)
GPU1: Allocating DAG for epoch #223 (2.74) GB
GPU1: Allocating buffers failed with: clCreateBuffer (-61).

Fatal error detected. Restarting.


As far as I knwo we are far ( 1 year ) from being at epoch so DAG file size is over 3 GB

Other miners continue to work properly ( e.g. : lolminer )

I use 5.7b but also tried with 5.4c

Any idea ?

I have the same problem, anyone found solution ?

one card in system? miner card connect to monitor?

The number of cards does not matter. The same on 1 card. Two, four. Connecting the monitor also does not matter. It was working normally. It stopped working on all computers overnight. I am currently using lolminer and it works fine. But I'd rather go back to Phoenix Miner ... I just don't know how.

I'm mining ETC ...


Same problem with 280x 3gb, will anyone solve this??

Hello,
The same problem here with r9 280/280x. Is there any solution?

I'm going to assume that you have done this ?

 -rvram  -1

If not, then do that.


There is only one solution to the problem so far - lolminer. hd7950 3Gb - 9,8 mh/s etc

"-rvram -1" doesn't help. The error is still the same.
Pages: « 1 ... 414 415 416 417 418 419 420 421 422 423 424 425 426 427 428 429 430 431 432 433 434 435 436 437 438 439 440 441 442 443 444 445 446 447 448 449 450 451 452 453 454 455 456 457 458 459 460 461 462 463 [464] 465 466 467 468 469 470 471 472 473 474 475 476 477 478 479 480 481 482 483 484 485 486 487 488 489 490 491 492 493 494 495 496 497 498 499 »
  Print  
 
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.19 | SMF © 2006-2009, Simple Machines Valid XHTML 1.0! Valid CSS!