Bitcoin Forum
November 20, 2018, 05:03:01 PM *
News: Latest Bitcoin Core release: 0.17.0 [Torrent].
 
   Home   Help Search Login Register More  
Pages: [1]
  Print  
Author Topic: Antminer S9 problem  (Read 157 times)
malamama
Newbie
*
Offline Offline

Activity: 11
Merit: 0


View Profile
April 19, 2018, 07:10:00 PM
 #1

I have this problem with a S9 antminer, i did the reboot and the factory reset, i was trying to download the firmware from Bitmain web but its impossible the file does not exist

https://ibb.co/hu4ap7

https://ibb.co/d4pEhS

Best regards
1542733381
Hero Member
*
Offline Offline

Posts: 1542733381

View Profile Personal Message (Offline)

Ignore
1542733381
Reply with quote  #2

1542733381
Report to moderator
Advertised sites are not endorsed by the Bitcoin Forum. They may be unsafe, untrustworthy, or illegal in your jurisdiction. Advertise here.
1542733381
Hero Member
*
Offline Offline

Posts: 1542733381

View Profile Personal Message (Offline)

Ignore
1542733381
Reply with quote  #2

1542733381
Report to moderator
fanatic26
Hero Member
*****
Offline Offline

Activity: 756
Merit: 560


View Profile
April 19, 2018, 08:57:01 PM
 #2

What you are showing is not a problem per se.

Hardware Version and bmminer version only show up if the machine is actively hashing. This is why your status page is empty. The machine has not started hashing yet. You need to give it time to start the process, I have had machines take 45 minutes before they started hashing right out of the box. Posting your kernel log for errors is something else that might help us identify the problem if you can still not connect after a period of time.

Stop buying industrial miners, running them at home, and then complaining about the noise.
malamama
Newbie
*
Offline Offline

Activity: 11
Merit: 0


View Profile
April 19, 2018, 11:04:35 PM
 #3

I still having the same error

Code:
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 3.14.0-xilinx-gb190cb0-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #57 SMP PREEMPT Fri Dec 9 14:49:22 CST 2016
[    0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine model: Xilinx Zynq
[    0.000000] cma: CMA: reserved 128 MiB at 16800000
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] On node 0 totalpages: 126976
[    0.000000] free_area_init_node: node 0, pgdat c0740a40, node_mem_map debd8000
[    0.000000]   Normal zone: 992 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 126976 pages, LIFO batch:31
[    0.000000] PERCPU: Embedded 8 pages/cpu @debc1000 s9088 r8192 d15488 u32768
[    0.000000] pcpu-alloc: s9088 r8192 d15488 u32768 alloc=8*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 125984
[    0.000000] Kernel command line: noinitrd mem=496M console=ttyPS0,115200 root=ubi0:rootfs ubi.mtd=1 rootfstype=ubifs rw rootwait
[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Memory: 364356K/507904K available (5032K kernel code, 283K rwdata, 1916K rodata, 204K init, 258K bss, 143548K reserved, 0K highmem)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xdf800000 - 0xff000000   ( 504 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xdf000000   ( 496 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc06d1374   (6949 kB)
[    0.000000]       .init : 0xc06d2000 - 0xc0705380   ( 205 kB)
[    0.000000]       .data : 0xc0706000 - 0xc074cf78   ( 284 kB)
[    0.000000]        .bss : 0xc074cf84 - 0xc078d9fc   ( 259 kB)
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] Dump stacks of tasks blocking RCU-preempt GP.
[    0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] ps7-slcr mapped to df802000
[    0.000000] zynq_clock_init: clkc starts at df802100
[    0.000000] Zynq clock init
[    0.000015] sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 3298534883328ns
[    0.000306] ps7-ttc #0 at df804000, irq=43
[    0.000613] Console: colour dummy device 80x30
[    0.000643] Calibrating delay loop... 1325.46 BogoMIPS (lpj=6627328)
[    0.040206] pid_max: default: 32768 minimum: 301
[    0.040427] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.040447] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.042599] CPU: Testing write buffer coherency: ok
[    0.042934] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.042992] Setting up static identity map for 0x4c4af8 - 0x4c4b50
[    0.043212] L310 cache controller enabled
[    0.043232] l2x0: 8 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x72760000, Cache size: 512 kB
[    0.121032] CPU1: Booted secondary processor
[    0.210227] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.210360] Brought up 2 CPUs
[    0.210378] SMP: Total of 2 processors activated.
[    0.210386] CPU: All CPU(s) started in SVC mode.
[    0.211049] devtmpfs: initialized
[    0.213475] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[    0.214683] regulator-dummy: no parameters
[    0.222352] NET: Registered protocol family 16
[    0.224636] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.226925] cpuidle: using governor ladder
[    0.226939] cpuidle: using governor menu
[    0.234316] syscon f8000000.ps7-slcr: regmap [mem 0xf8000000-0xf8000fff] registered
[    0.235825] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[    0.235839] hw-breakpoint: maximum watchpoint size is 4 bytes.
[    0.235950] zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xdf880000
[    0.257596] bio: create slab <bio-0> at 0
[    0.259018] vgaarb: loaded
[    0.259696] SCSI subsystem initialized
[    0.260782] usbcore: registered new interface driver usbfs
[    0.260959] usbcore: registered new interface driver hub
[    0.261221] usbcore: registered new device driver usb
[    0.261750] media: Linux media interface: v0.10
[    0.261908] Linux video capture interface: v2.00
[    0.262156] pps_core: LinuxPPS API ver. 1 registered
[    0.262167] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.262297] PTP clock support registered
[    0.262654] EDAC MC: Ver: 3.0.0
[    0.263698] Advanced Linux Sound Architecture Driver Initialized.
[    0.266550] DMA-API: preallocated 4096 debug entries
[    0.266564] DMA-API: debugging enabled by kernel config
[    0.266641] Switched to clocksource arm_global_timer
[    0.287671] NET: Registered protocol family 2
[    0.288334] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[    0.288392] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[    0.288477] TCP: Hash tables configured (established 4096 bind 4096)
[    0.288521] TCP: reno registered
[    0.288538] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.288570] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.288806] NET: Registered protocol family 1
[    0.289145] RPC: Registered named UNIX socket transport module.
[    0.289157] RPC: Registered udp transport module.
[    0.289166] RPC: Registered tcp transport module.
[    0.289174] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.289187] PCI: CLS 0 bytes, default 64
[    0.289624] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[    0.291629] futex hash table entries: 512 (order: 3, 32768 bytes)
[    0.293765] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[    0.293947] msgmni has been set to 967
[    0.294726] io scheduler noop registered
[    0.294739] io scheduler deadline registered
[    0.294794] io scheduler cfq registered (default)
[    0.302787] dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-2364208
[    0.302808] dma-pl330 f8003000.ps7-dma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
[    0.426131] e0001000.serial: ttyPS0 at MMIO 0xe0001000 (irq = 82, base_baud = 3124999) is a xuartps
[    0.993501] console [ttyPS0] enabled
[    0.997777] xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to df866000
[    1.005396] [drm] Initialized drm 1.1.0 20060810
[    1.022327] brd: module loaded
[    1.031795] loop: module loaded
[    1.041315] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
[    1.047340] e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
[    1.055117] libphy: XEMACPS mii bus: probed
[    1.059704] ------------- phy_id = 0x3625e62
[    1.064431] xemacps e000b000.ps7-ethernet: pdev->id -1, baseaddr 0xe000b000, irq 54
[    1.073047] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.079703] ehci-pci: EHCI PCI platform driver
[    1.086933] zynq-dr e0002000.ps7-usb: Unable to init USB phy, missing?
[    1.093734] usbcore: registered new interface driver usb-storage
[    1.100603] mousedev: PS/2 mouse device common for all mice
[    1.106712] i2c /dev entries driver
[    1.113585] zynq-edac f8006000.ps7-ddrc: ecc not enabled
[    1.119136] cpufreq_cpu0: failed to get cpu0 regulator: -19
[    1.125012] Xilinx Zynq CpuIdle Driver started
[    1.129891] sdhci: Secure Digital Host Controller Interface driver
[    1.135983] sdhci: Copyright(c) Pierre Ossman
[    1.140369] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.147142] mmc0: no vqmmc regulator found
[    1.151159] mmc0: no vmmc regulator found
[    1.186661] mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
[    1.195353] usbcore: registered new interface driver usbhid
[    1.200863] usbhid: USB HID core driver
[    1.205576] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
[    1.211878] nand: Micron MT29F2G08ABAEAWP
[    1.215842] nand: 256MiB, SLC, page size: 2048, OOB size: 64
[    1.221784] Bad block table found at page 131008, version 0x01
[    1.228010] Bad block table found at page 130944, version 0x01
[    1.234007] nand_read_bbt: bad block at 0x00000c980000
[    1.239094] nand_read_bbt: bad block at 0x00000cda0000
[    1.244180] nand_read_bbt: bad block at 0x00000d040000
[    1.249328] nand_read_bbt: bad block at 0x00000d420000
[    1.254479] 3 ofpart partitions found on MTD device pl353-nand
[    1.260256] Creating 3 MTD partitions on "pl353-nand":
[    1.265365] 0x000000000000-0x000002000000 : "BOOT.bin-env-dts-kernel"
[    1.273421] 0x000002000000-0x00000b000000 : "angstram-rootfs"
[    1.280736] 0x00000b000000-0x000010000000 : "upgrade-rootfs"
[    1.289651] TCP: cubic registered
[    1.292887] NET: Registered protocol family 17
[    1.297617] Registering SWP/SWPB emulation handler
[    1.303497] regulator-dummy: disabling
[    1.307866] UBI: attaching mtd1 to ubi0
[    1.834897] UBI: scanning is finished
[    1.846527] UBI: attached mtd1 (name "angstram-rootfs", size 144 MiB) to ubi0
[    1.853607] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    1.860368] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    1.867053] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
[    1.873889] UBI: good PEBs: 1152, bad PEBs: 0, corrupted PEBs: 0
[    1.879891] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
[    1.887014] UBI: max/mean erase counter: 246/94, WL threshold: 4096, image sequence number: 916511165
[    1.896197] UBI: available PEBs: 0, total reserved PEBs: 1152, PEBs reserved for bad PEB handling: 40
[    1.905432] UBI: background thread "ubi_bgt0d" started, PID 1080
[    1.905438] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[    1.909412] ALSA device list:
[    1.909416]   No soundcards found.
[    1.925790] UBIFS: background thread "ubifs_bgt0_0" started, PID 1082
[    1.954886] UBIFS: recovery needed
[    2.071024] UBIFS: recovery completed
[    2.074695] UBIFS: mounted UBI device 0, volume 0, name "rootfs"
[    2.080642] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[    2.089748] UBIFS: FS size: 128626688 bytes (122 MiB, 1013 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
[    2.099643] UBIFS: reserved for root: 0 bytes (0 KiB)
[    2.104667] UBIFS: media format: w4/r0 (latest is w4/r0), UUID BBDF9B01-1A34-456B-9FBF-33B446951E64, small LPT model
[    2.115739] VFS: Mounted root (ubifs filesystem) on device 0:11.
[    2.122465] devtmpfs: mounted
[    2.125566] Freeing unused kernel memory: 204K (c06d2000 - c0705000)
[    2.962526] random: dd urandom read with 0 bits of entropy available
[    3.356676]
[    3.356676] bcm54xx_config_init
[    3.966686]
[    3.966686] bcm54xx_config_init
[    6.967519] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[    6.973612] xemacps e000b000.ps7-ethernet: link up (100/FULL)
[   36.432057] In axi fpga driver!
[   36.435127] request_mem_region OK!
[   36.438557] AXI fpga dev virtual address is 0xdf9fc000
[   36.443625] *base_vir_addr = 0x8c510
[   36.458906] In fpga mem driver!
[   36.461992] request_mem_region OK!
[   36.465557] fpga mem virtual address is 0xe2000000
[   37.276013]
[   37.276013] bcm54xx_config_init
[   37.905923]
[   37.905923] bcm54xx_config_init
[   40.906453] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[   40.912473] xemacps e000b000.ps7-ethernet: link up (100/FULL)
[  869.913967] random: nonblocking pool is initialized
[ 1372.757602] xemacps e000b000.ps7-ethernet: link down
[ 1397.754511] xemacps e000b000.ps7-ethernet: link up (100/FULL)
[ 1403.753758] xemacps e000b000.ps7-ethernet: link down
[ 1405.753511] xemacps e000b000.ps7-ethernet: link up (100/FULL)
This is XILINX board. Totalram:       507527168
Detect 512MB control board of XILINX
DETECT HW version=0008c510
miner ID : 81440c411375885c
Miner Type = S9
AsicType = 1387
real AsicNum = 63
use critical mode to search freq...
get PLUG ON=0x000000e0
Find hashboard on Chain[5]
Find hashboard on Chain[6]
Find hashboard on Chain[7]
set_reset_allhashboard = 0x0000ffff
Check chain[5] PIC fw version=0x03
Check chain[6] PIC fw version=0x03
Check chain[7] PIC fw version=0x03
chain[5]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
has freq in PIC, will disable freq setting.
chain[5] has freq in PIC and will jump over...
Chain[5] has core num in PIC
Chain[5] ASIC[12] has core num=15
Check chain[5] PIC fw version=0x03
chain[6]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
has freq in PIC, will disable freq setting.
chain[6] has freq in PIC and will jump over...
Chain[6] has core num in PIC
Chain[6] ASIC[0] has core num=1
Chain[6] ASIC[1] has core num=1
Chain[6] ASIC[2] has core num=1
Chain[6] ASIC[3] has core num=1
Chain[6] ASIC[4] has core num=1
Chain[6] ASIC[5] has core num=1
Chain[6] ASIC[6] has core num=1
Chain[6] ASIC[7] has core num=1
Chain[6] ASIC[8] has core num=1
Chain[6] ASIC[9] has core num=1
Chain[6] ASIC[10] has core num=2
Chain[6] ASIC[11] has core num=1
Chain[6] ASIC[12] has core num=1
Chain[6] ASIC[14] has core num=1
Chain[6] ASIC[15] has core num=1
Chain[6] ASIC[16] has core num=1
Chain[6] ASIC[17] has core num=1
Chain[6] ASIC[18] has core num=1
Chain[6] ASIC[19] has core num=1
Chain[6] ASIC[20] has core num=3
Chain[6] ASIC[21] has core num=1
Chain[6] ASIC[22] has core num=1
Chain[6] ASIC[23] has core num=1
Chain[6] ASIC[24] has core num=1
Chain[6] ASIC[25] has core num=1
Chain[6] ASIC[26] has core num=1
Chain[6] ASIC[27] has core num=1
Chain[6] ASIC[28] has core num=1
Chain[6] ASIC[29] has core num=1
Chain[6] ASIC[30] has core num=1
Chain[6] ASIC[31] has core num=1
Chain[6] ASIC[32] has core num=1
Chain[6] ASIC[33] has core num=1
Chain[6] ASIC[34] has core num=1
Chain[6] ASIC[35] has core num=3
Chain[6] ASIC[36] has core num=2
Chain[6] ASIC[37] has core num=1
Chain[6] ASIC[38] has core num=1
Chain[6] ASIC[39] has core num=1
Chain[6] ASIC[40] has core num=1
Chain[6] ASIC[41] has core num=1
Chain[6] ASIC[42] has core num=1
Chain[6] ASIC[43] has core num=1
Chain[6] ASIC[44] has core num=1
Chain[6] ASIC[45] has core num=1
Chain[6] ASIC[46] has core num=1
Chain[6] ASIC[47] has core num=1
Chain[6] ASIC[48] has core num=2
Chain[6] ASIC[49] has core num=1
Chain[6] ASIC[50] has core num=1
Chain[6] ASIC[51] has core num=1
Chain[6] ASIC[52] has core num=1
Chain[6] ASIC[53] has core num=1
Chain[6] ASIC[54] has core num=3
Chain[6] ASIC[55] has core num=1
Chain[6] ASIC[56] has core num=1
Chain[6] ASIC[57] has core num=1
Chain[6] ASIC[58] has core num=1
Chain[6] ASIC[59] has core num=1
Chain[6] ASIC[60] has core num=1
Chain[6] ASIC[61] has core num=1
Chain[6] ASIC[62] has core num=1
Check chain[6] PIC fw version=0x03
chain[7]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
has freq in PIC, will disable freq setting.
chain[7] has freq in PIC and will jump over...
Chain[7] has core num in PIC
Check chain[7] PIC fw version=0x03
get PIC voltage=91 on chain[5], value=890
get PIC voltage=91 on chain[6], value=890
get PIC voltage=91 on chain[7], value=890
set_reset_allhashboard = 0x00000000
chain[5] temp offset record: 62,0,0,0,0,0,38,28
chain[5] temp chip I2C addr=0x9a
chain[5] has no middle temp, use special fix mode.
chain[6] temp offset record: 62,0,0,0,0,0,38,28
chain[6] temp chip I2C addr=0x9a
chain[6] has no middle temp, use special fix mode.
chain[7] temp offset record: 62,0,0,0,0,0,38,28
chain[7] temp chip I2C addr=0x9a
chain[7] has no middle temp, use special fix mode.
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
CRC error counter=0
set command mode to VIL

--- check asic number
set_baud=0
The min freq=700
set real timeout 52, need sleep=379392
After TEST CRC error counter=0
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
search freq for 1 times, completed chain = 3, total chain num = 3
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
restart Miner chance num=2
waiting for receive_func to exit!
waiting for pic heart to exit!
bmminer not found=16175 root       0:00 grep bmminer

bmminer not found, restart bmminer ...
bmminer not found=16670 root       0:00 grep bmminer

bmminer not found, restart bmminer ...
bmminer not found= 3658 root       0:00 grep bmminer

bmminer not found, restart bmminer ...
bmminer not found=23292 root       0:00 grep bmminer

bmminer not found, restart bmminer ...
This is user mode for mining
Detect 512MB control board of XILINX
Miner Type = S9
Miner compile time: Fri Jul 21 05:15:25 EDT 2017 type: Antminer S9set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
set_reset_allhashboard = 0x0000ffff
miner ID : 81440c411375885c
set_reset_allhashboard = 0x0000ffff
Checking fans!get fan[2] speed=5400
get fan[2] speed=5400
get fan[2] speed=5400
get fan[2] speed=5400
get fan[2] speed=5400
get fan[2] speed=5400
get fan[5] speed=6000
get fan[2] speed=5400
get fan[5] speed=6000
get fan[2] speed=5400
get fan[5] speed=6000
chain[5]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
Detect: use voltage limit rules on single board!
Detect: use lower voltage on searching freq!
Chain[J6] has backup chain_voltage=890
Check chain[5] PIC fw version=0x03
chain[6]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
Detect: use voltage limit rules on single board!
Detect: use lower voltage on searching freq!
Chain[J7] has backup chain_voltage=890
Check chain[6] PIC fw version=0x03
chain[7]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
Detect: use voltage limit rules on single board!
Detect: use lower voltage on searching freq!
Chain[J8] has backup chain_voltage=890
Check chain[7] PIC fw version=0x03
Chain[J6] orignal chain_voltage_pic=91 value=890
Chain[J7] orignal chain_voltage_pic=91 value=890
Chain[J8] orignal chain_voltage_pic=91 value=890
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
Chain[J6] has 63 asic
Chain[J7] has 63 asic
Chain[J8] has 63 asic
Chain[J6] has core num in PIC
Chain[J6] ASIC[12] has core num=15
Chain[J7] has core num in PIC
Chain[J7] ASIC[0] has core num=1
Chain[J7] ASIC[1] has core num=1
Chain[J7] ASIC[2] has core num=1
Chain[J7] ASIC[3] has core num=1
Chain[J7] ASIC[4] has core num=1
Chain[J7] ASIC[5] has core num=1
Chain[J7] ASIC[6] has core num=1
Chain[J7] ASIC[7] has core num=1
Chain[J7] ASIC[8] has core num=1
Chain[J7] ASIC[9] has core num=1
Chain[J7] ASIC[10] has core num=2
Chain[J7] ASIC[11] has core num=1
Chain[J7] ASIC[12] has core num=1
Chain[J7] ASIC[14] has core num=1
Chain[J7] ASIC[15] has core num=1
Chain[J7] ASIC[16] has core num=1
Chain[J7] ASIC[17] has core num=1
Chain[J7] ASIC[18] has core num=1
Chain[J7] ASIC[19] has core num=1
Chain[J7] ASIC[20] has core num=3
Chain[J7] ASIC[21] has core num=1
Chain[J7] ASIC[22] has core num=1
Chain[J7] ASIC[23] has core num=1
Chain[J7] ASIC[24] has core num=1
Chain[J7] ASIC[25] has core num=1
Chain[J7] ASIC[26] has core num=1
Chain[J7] ASIC[27] has core num=1
Chain[J7] ASIC[28] has core num=1
Chain[J7] ASIC[29] has core num=1
Chain[J7] ASIC[30] has core num=1
Chain[J7] ASIC[31] has core num=1
Chain[J7] ASIC[32] has core num=1
Chain[J7] ASIC[33] has core num=1
Chain[J7] ASIC[34] has core num=1
Chain[J7] ASIC[35] has core num=3
Chain[J7] ASIC[36] has core num=2
Chain[J7] ASIC[37] has core num=1
Chain[J7] ASIC[38] has core num=1
Chain[J7] ASIC[39] has core num=1
Chain[J7] ASIC[40] has core num=1
Chain[J7] ASIC[41] has core num=1
Chain[J7] ASIC[42] has core num=1
Chain[J7] ASIC[43] has core num=1
Chain[J7] ASIC[44] has core num=1
Chain[J7] ASIC[45] has core num=1
Chain[J7] ASIC[46] has core num=1
Chain[J7] ASIC[47] has core num=1
Chain[J7] ASIC[48] has core num=2
Chain[J7] ASIC[49] has core num=1
Chain[J7] ASIC[50] has core num=1
Chain[J7] ASIC[51] has core num=1
Chain[J7] ASIC[52] has core num=1
Chain[J7] ASIC[53] has core num=1
Chain[J7] ASIC[54] has core num=3
Chain[J7] ASIC[55] has core num=1
Chain[J7] ASIC[56] has core num=1
Chain[J7] ASIC[57] has core num=1
Chain[J7] ASIC[58] has core num=1
Chain[J7] ASIC[59] has core num=1
Chain[J7] ASIC[60] has core num=1
Chain[J7] ASIC[61] has core num=1
Chain[J7] ASIC[62] has core num=1
Chain[J8] has core num in PIC
miner total rate=13692GH/s fixed rate=13500GH/s
read PIC voltage=940 on chain[5]
Chain:5 chipnum=63
Chain[J6] voltage added=0.0V
Chain:5 temp offset=0
Chain:5 base freq=643
Asic[ 0]:643
Asic[ 1]:643 Asic[ 2]:643 Asic[ 3]:643 Asic[ 4]:643 Asic[ 5]:643 Asic[ 6]:643 Asic[ 7]:643 Asic[ 8]:643
Asic[ 9]:643 Asic[10]:643 Asic[11]:643 Asic[12]:643 Asic[13]:643 Asic[14]:643 Asic[15]:643 Asic[16]:643
Asic[17]:643 Asic[18]:643 Asic[19]:643 Asic[20]:643 Asic[21]:643 Asic[22]:643 Asic[23]:643 Asic[24]:643
Asic[25]:643 Asic[26]:643 Asic[27]:643 Asic[28]:643 Asic[29]:643 Asic[30]:643 Asic[31]:643 Asic[32]:643
Asic[33]:643 Asic[34]:643 Asic[35]:643 Asic[36]:643 Asic[37]:643 Asic[38]:643 Asic[39]:643 Asic[40]:643
Asic[41]:643 Asic[42]:643 Asic[43]:643 Asic[44]:643 Asic[45]:643 Asic[46]:643 Asic[47]:643 Asic[48]:643
Asic[49]:643 Asic[50]:643 Asic[51]:643 Asic[52]:643 Asic[53]:643 Asic[54]:643 Asic[55]:643 Asic[56]:643
Asic[57]:643 Asic[58]:643 Asic[59]:643 Asic[60]:643 Asic[61]:643 Asic[62]:643
Chain:5 max freq=643
Chain:5 min freq=643

read PIC voltage=940 on chain[6]
Chain:6 chipnum=63
Chain[J7] voltage added=0.0V
Chain:6 temp offset=0
Chain:6 base freq=643
Asic[ 0]:643
Asic[ 1]:643 Asic[ 2]:643 Asic[ 3]:643 Asic[ 4]:643 Asic[ 5]:643 Asic[ 6]:643 Asic[ 7]:643 Asic[ 8]:643
Asic[ 9]:643 Asic[10]:643 Asic[11]:643 Asic[12]:643 Asic[13]:643 Asic[14]:643 Asic[15]:643 Asic[16]:643
Asic[17]:643 Asic[18]:643 Asic[19]:643 Asic[20]:643 Asic[21]:643 Asic[22]:643 Asic[23]:643 Asic[24]:643
Asic[25]:643 Asic[26]:643 Asic[27]:643 Asic[28]:643 Asic[29]:643 Asic[30]:643 Asic[31]:643 Asic[32]:643
Asic[33]:643 Asic[34]:643 Asic[35]:643 Asic[36]:643 Asic[37]:643 Asic[38]:643 Asic[39]:643 Asic[40]:643
Asic[41]:643 Asic[42]:643 Asic[43]:643 Asic[44]:643 Asic[45]:643 Asic[46]:643 Asic[47]:643 Asic[48]:643
Asic[49]:643 Asic[50]:643 Asic[51]:643 Asic[52]:643 Asic[53]:643 Asic[54]:643 Asic[55]:643 Asic[56]:643
Asic[57]:643 Asic[58]:643 Asic[59]:643 Asic[60]:643 Asic[61]:643 Asic[62]:643
Chain:6 max freq=643
Chain:6 min freq=643

read PIC voltage=940 on chain[7]
Chain:7 chipnum=63
Chain[J8] voltage added=0.0V
Chain:7 temp offset=0
Chain:7 base freq=637
Asic[ 0]:637
Asic[ 1]:637 Asic[ 2]:637 Asic[ 3]:637 Asic[ 4]:637 Asic[ 5]:637 Asic[ 6]:637 Asic[ 7]:637 Asic[ 8]:637
Asic[ 9]:637 Asic[10]:637 Asic[11]:637 Asic[12]:637 Asic[13]:637 Asic[14]:637 Asic[15]:637 Asic[16]:637
Asic[17]:637 Asic[18]:637 Asic[19]:637 Asic[20]:637 Asic[21]:637 Asic[22]:637 Asic[23]:637 Asic[24]:637
Asic[25]:637 Asic[26]:637 Asic[27]:637 Asic[28]:637 Asic[29]:637 Asic[30]:637 Asic[31]:637 Asic[32]:637
Asic[33]:637 Asic[34]:637 Asic[35]:637 Asic[36]:637 Asic[37]:637 Asic[38]:637 Asic[39]:637 Asic[40]:637
Asic[41]:637 Asic[42]:637 Asic[43]:637 Asic[44]:637 Asic[45]:637 Asic[46]:637 Asic[47]:637 Asic[48]:637
Asic[49]:637 Asic[50]:637 Asic[51]:637 Asic[52]:637 Asic[53]:637 Asic[54]:637 Asic[55]:637 Asic[56]:637
Asic[57]:637 Asic[58]:637 Asic[59]:637 Asic[60]:637 Asic[61]:637 Asic[62]:637
Chain:7 max freq=637
Chain:7 min freq=637


Miner fix freq ...
read PIC voltage=940 on chain[5]
Chain:5 chipnum=63
Chain[J6] voltage added=0.0V
Chain:5 temp offset=0
Chain:5 base freq=643
Asic[ 0]:643
Asic[ 1]:643 Asic[ 2]:643 Asic[ 3]:643 Asic[ 4]:643 Asic[ 5]:643 Asic[ 6]:643 Asic[ 7]:643 Asic[ 8]:643
Asic[ 9]:643 Asic[10]:643 Asic[11]:643 Detect a bad chip=12 on chain[5], fixed to 400M
Asic[12]:643 Asic[13]:643 Asic[14]:643 Asic[15]:643 Asic[16]:643
Asic[17]:643 Asic[18]:643 Asic[19]:643 Asic[20]:643 Asic[21]:643 Asic[22]:643 Asic[23]:643 Asic[24]:643
Asic[25]:643 Asic[26]:643 Asic[27]:643 Asic[28]:643 Asic[29]:643 Asic[30]:643 Asic[31]:643 Asic[32]:643
Asic[33]:643 Asic[34]:643 Asic[35]:643 Asic[36]:643 Asic[37]:643 Asic[38]:643 Asic[39]:643 Asic[40]:643
Asic[41]:643 Asic[42]:643 Asic[43]:643 Asic[44]:643 Asic[45]:643 Asic[46]:643 Asic[47]:643 Asic[48]:643
Asic[49]:643 Asic[50]:643 Asic[51]:643 Asic[52]:643 Asic[53]:643 Asic[54]:643 Asic[55]:643 Asic[56]:643
Asic[57]:643 Asic[58]:643 Asic[59]:643 Asic[60]:643 Asic[61]:643 Asic[62]:643
Chain:5 max freq=643
Chain:5 min freq=643

read PIC voltage=940 on chain[6]
Chain:6 chipnum=63
Chain[J7] voltage added=0.0V
Chain:6 temp offset=0
Chain:6 base freq=643
Asic[ 0]:643
Asic[ 1]:643 Asic[ 2]:643 Asic[ 3]:643 Asic[ 4]:643 Asic[ 5]:643 Asic[ 6]:643 Asic[ 7]:643 Asic[ 8]:643
Asic[ 9]:643 Asic[10]:643 Asic[11]:643 Asic[12]:643 Asic[13]:643 Asic[14]:643 Asic[15]:643 Asic[16]:643
Asic[17]:643 Asic[18]:643 Asic[19]:643 Asic[20]:643 Asic[21]:643 Asic[22]:643 Asic[23]:643 Asic[24]:643
Asic[25]:643 Asic[26]:643 Asic[27]:643 Asic[28]:643 Asic[29]:643 Asic[30]:643 Asic[31]:643 Asic[32]:643
Asic[33]:643 Asic[34]:643 Asic[35]:643 Asic[36]:643 Asic[37]:643 Asic[38]:643 Asic[39]:643 Asic[40]:643
Asic[41]:643 Asic[42]:643 Asic[43]:643 Asic[44]:643 Asic[45]:643 Asic[46]:643 Asic[47]:643 Asic[48]:643
Asic[49]:643 Asic[50]:643 Asic[51]:643 Asic[52]:643 Asic[53]:643 Asic[54]:643 Asic[55]:643 Asic[56]:643
Asic[57]:643 Asic[58]:643 Asic[59]:643 Asic[60]:643 Asic[61]:643 Asic[62]:643
Chain:6 max freq=643
Chain:6 min freq=643

read PIC voltage=940 on chain[7]
Chain:7 chipnum=63
Chain[J8] voltage added=0.0V
Chain:7 temp offset=0
Chain:7 base freq=637
Asic[ 0]:637
Asic[ 1]:637 Asic[ 2]:637 Asic[ 3]:637 Asic[ 4]:637 Asic[ 5]:637 Asic[ 6]:637 Asic[ 7]:637 Asic[ 8]:637
Asic[ 9]:637 Asic[10]:637 Asic[11]:637 Asic[12]:637 Asic[13]:637 Asic[14]:637 Asic[15]:637 Asic[16]:637
Asic[17]:637 Asic[18]:637 Asic[19]:637 Asic[20]:637 Asic[21]:637 Asic[22]:637 Asic[23]:637 Asic[24]:637
Asic[25]:637 Asic[26]:637 Asic[27]:637 Asic[28]:637 Asic[29]:637 Asic[30]:637 Asic[31]:637 Asic[32]:637
Asic[33]:637 Asic[34]:637 Asic[35]:637 Asic[36]:637 Asic[37]:637 Asic[38]:637 Asic[39]:637 Asic[40]:637
Asic[41]:637 Asic[42]:637 Asic[43]:637 Asic[44]:637 Asic[45]:637 Asic[46]:637 Asic[47]:637 Asic[48]:637
Asic[49]:637 Asic[50]:637 Asic[51]:637 Asic[52]:637 Asic[53]:637 Asic[54]:637 Asic[55]:637 Asic[56]:637
Asic[57]:637 Asic[58]:637 Asic[59]:637 Asic[60]:637 Asic[61]:637 Asic[62]:637
Chain:7 max freq=637
Chain:7 min freq=637

max freq = 643
set baud=1
Chain[J6] PIC temp offset=62,0,0,0,0,0,38,28
chain[5] temp chip I2C addr=0x9a
chain[5] has no middle temp, use special fix mode.
Chain[J6] chip[244] use PIC middle temp offset=0 typeID=55
New offset Chain[5] chip[244] local:38 remote:41 offset:28
Chain[J6] chip[244] get middle temp offset=28 typeID=55
Chain[J7] PIC temp offset=62,0,0,0,0,0,38,28
chain[6] temp chip I2C addr=0x9a
chain[6] has no middle temp, use special fix mode.
Chain[J7] chip[244] use PIC middle temp offset=0 typeID=55
New offset Chain[6] chip[244] local:34 remote:38 offset:27
Chain[J7] chip[244] get middle temp offset=27 typeID=55
Chain[J8] PIC temp offset=62,0,0,0,0,0,38,28
chain[7] temp chip I2C addr=0x9a
chain[7] has no middle temp, use special fix mode.
Chain[J8] chip[244] use PIC middle temp offset=0 typeID=55
New offset Chain[7] chip[244] local:36 remote:40 offset:27
Chain[J8] chip[244] get middle temp offset=27 typeID=55
single board rate=4544 voltage limit=890 on chain[5]
get PIC voltage=890 on chain[5], check: must be < 890
single board rate=4572 voltage limit=890 on chain[6]
get PIC voltage=890 on chain[6], check: must be < 890
single board rate=4574 voltage limit=890 on chain[7]
get PIC voltage=890 on chain[7], check: must be < 890
Chain[J6] set working voltage=890 [91]
Chain[J7] set working voltage=890 [91]
Chain[J8] set working voltage=890 [91]
do heat board 8xPatten for 1 times
start send works on chain[5]
start send works on chain[6]
start send works on chain[7]
do read_temp_func once...
do check_asic_reg 0x08
Done check_asic_reg
do read temp on Chain[5]
Chain[5] Chip[62] TempTypeID=55 middle offset=28
Chain[5] Chip[62] local Temp=48
Chain[5] Chip[62] middle Temp=36
Special fix Chain[5] Chip[62] middle Temp = 63
Done read temp on Chain[5]
do read temp on Chain[6]
Chain[6] Chip[62] TempTypeID=55 middle offset=27
Chain[6] Chip[62] local Temp=45
Chain[6] Chip[62] middle Temp=35
Special fix Chain[6] Chip[62] middle Temp = 60
Done read temp on Chain[6]
do read temp on Chain[7]
Chain[7] Chip[62] TempTypeID=55 middle offset=27
Chain[7] Chip[62] local Temp=47
Chain[7] Chip[62] middle Temp=36
Special fix Chain[7] Chip[62] middle Temp = 62
Done read temp on Chain[7]
set FAN speed according to: temp_highest=48 temp_top1[PWM_T]=48 temp_top1[TEMP_POS_LOCAL]=48 temp_change=3 fix_fan_steps=0
set normal FAN speed...
FAN PWM: 46
read_temp_func Done!
CRC error counter=0



Moderator's note: This post was edited by frodocooper to add code tags.
BitMaxz
Legendary
*
Offline Offline

Activity: 1246
Merit: 1038

Bitmain miners is getting worst.


View Profile WWW
April 19, 2018, 11:07:12 PM
 #4

What actually shown in the hardware version? Sometimes it's a firmware issue if your hardware version is X.X.X.X or 0.0.0.0 your firmware might be corrupted.

If the reset doesn't work the next thing you can do now is to update it with firmware.

You can download the firmware from bitmain here https://shop.bitmain.com/support.htm?pid=00720161126080548570Q2tDBXAH065D

I hope that you can add more information about your miner problem so that we can find the solution for your issue.

Code:
Edit: Please use the insert code by click the sharp when creating message before you post just like this

"Unable to init USB phy" something missing according to your log

Code:
[    1.086933] zynq-dr e0002000.ps7-usb: Unable to init USB phy, missing?
[    1.093734] usbcore: registered new interface driver usb-storage
[    1.100603] mousedev: PS/2 mouse device common for all mice
[    1.106712] i2c /dev entries driver
[    1.113585] zynq-edac f8006000.ps7-ddrc: ecc not enabled
[    1.119136] cpufreq_cpu0: failed to get cpu0 regulator: -19

Flashing or update your firmware might fix the issue.

malamama
Newbie
*
Offline Offline

Activity: 11
Merit: 0


View Profile
April 19, 2018, 11:43:08 PM
 #5

Code:
ok  ;D

Quote
Which firmware i should select, I have a S9 13,5T


malamama
Newbie
*
Offline Offline

Activity: 11
Merit: 0


View Profile
April 20, 2018, 01:26:59 AM
 #6

Now i have this problem
https://ibb.co/nRp397

Code:
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 3.14.0-xilinx-gb190cb0-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #57 SMP PREEMPT Fri Dec 9 14:49:22 CST 2016
[    0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine model: Xilinx Zynq
[    0.000000] cma: CMA: reserved 128 MiB at 16800000
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] On node 0 totalpages: 126976
[    0.000000] free_area_init_node: node 0, pgdat c0740a40, node_mem_map debd8000
[    0.000000]   Normal zone: 992 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 126976 pages, LIFO batch:31
[    0.000000] PERCPU: Embedded 8 pages/cpu @debc1000 s9088 r8192 d15488 u32768
[    0.000000] pcpu-alloc: s9088 r8192 d15488 u32768 alloc=8*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 125984
[    0.000000] Kernel command line: noinitrd mem=496M console=ttyPS0,115200 root=ubi0:rootfs ubi.mtd=1 rootfstype=ubifs rw rootwait
[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Memory: 364356K/507904K available (5032K kernel code, 283K rwdata, 1916K rodata, 204K init, 258K bss, 143548K reserved, 0K highmem)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xdf800000 - 0xff000000   ( 504 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xdf000000   ( 496 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc06d1374   (6949 kB)
[    0.000000]       .init : 0xc06d2000 - 0xc0705380   ( 205 kB)
[    0.000000]       .data : 0xc0706000 - 0xc074cf78   ( 284 kB)
[    0.000000]        .bss : 0xc074cf84 - 0xc078d9fc   ( 259 kB)
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] Dump stacks of tasks blocking RCU-preempt GP.
[    0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] ps7-slcr mapped to df802000
[    0.000000] zynq_clock_init: clkc starts at df802100
[    0.000000] Zynq clock init
[    0.000015] sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 3298534883328ns
[    0.000306] ps7-ttc #0 at df804000, irq=43
[    0.000610] Console: colour dummy device 80x30
[    0.000641] Calibrating delay loop... 1325.46 BogoMIPS (lpj=6627328)
[    0.040207] pid_max: default: 32768 minimum: 301
[    0.040425] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.040446] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.042591] CPU: Testing write buffer coherency: ok
[    0.042925] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.042985] Setting up static identity map for 0x4c4af8 - 0x4c4b50
[    0.043208] L310 cache controller enabled
[    0.043227] l2x0: 8 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x72760000, Cache size: 512 kB
[    0.121037] CPU1: Booted secondary processor
[    0.210228] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.210358] Brought up 2 CPUs
[    0.210377] SMP: Total of 2 processors activated.
[    0.210385] CPU: All CPU(s) started in SVC mode.
[    0.211049] devtmpfs: initialized
[    0.213470] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[    0.214679] regulator-dummy: no parameters
[    0.222349] NET: Registered protocol family 16
[    0.224594] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.226883] cpuidle: using governor ladder
[    0.226896] cpuidle: using governor menu
[    0.234292] syscon f8000000.ps7-slcr: regmap [mem 0xf8000000-0xf8000fff] registered
[    0.235805] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[    0.235819] hw-breakpoint: maximum watchpoint size is 4 bytes.
[    0.235932] zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xdf880000
[    0.257724] bio: create slab <bio-0> at 0
[    0.259150] vgaarb: loaded
[    0.259860] SCSI subsystem initialized
[    0.260846] usbcore: registered new interface driver usbfs
[    0.261018] usbcore: registered new interface driver hub
[    0.261292] usbcore: registered new device driver usb
[    0.261822] media: Linux media interface: v0.10
[    0.261988] Linux video capture interface: v2.00
[    0.262227] pps_core: LinuxPPS API ver. 1 registered
[    0.262238] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.262359] PTP clock support registered
[    0.262716] EDAC MC: Ver: 3.0.0
[    0.263753] Advanced Linux Sound Architecture Driver Initialized.
[    0.266581] DMA-API: preallocated 4096 debug entries
[    0.266594] DMA-API: debugging enabled by kernel config
[    0.266671] Switched to clocksource arm_global_timer
[    0.287753] NET: Registered protocol family 2
[    0.288408] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[    0.288465] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[    0.288550] TCP: Hash tables configured (established 4096 bind 4096)
[    0.288596] TCP: reno registered
[    0.288614] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.288647] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.288883] NET: Registered protocol family 1
[    0.289223] RPC: Registered named UNIX socket transport module.
[    0.289235] RPC: Registered udp transport module.
[    0.289243] RPC: Registered tcp transport module.
[    0.289252] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.289265] PCI: CLS 0 bytes, default 64
[    0.289698] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[    0.291688] futex hash table entries: 512 (order: 3, 32768 bytes)
[    0.293780] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[    0.293970] msgmni has been set to 967
[    0.294742] io scheduler noop registered
[    0.294755] io scheduler deadline registered
[    0.294809] io scheduler cfq registered (default)
[    0.305848] dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-2364208
[    0.305868] dma-pl330 f8003000.ps7-dma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
[    0.427591] e0001000.serial: ttyPS0 at MMIO 0xe0001000 (irq = 82, base_baud = 3124999) is a xuartps
[    0.995032] console [ttyPS0] enabled
[    0.999311] xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to df866000
[    1.006966] [drm] Initialized drm 1.1.0 20060810
[    1.023921] brd: module loaded
[    1.033279] loop: module loaded
[    1.042745] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
[    1.048800] e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
[    1.056554] libphy: XEMACPS mii bus: probed
[    1.060955] ------------- phy_id = 0x3625e62
[    1.065679] xemacps e000b000.ps7-ethernet: pdev->id -1, baseaddr 0xe000b000, irq 54
[    1.074334] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.081138] ehci-pci: EHCI PCI platform driver
[    1.088372] zynq-dr e0002000.ps7-usb: Unable to init USB phy, missing?
[    1.095177] usbcore: registered new interface driver usb-storage
[    1.102062] mousedev: PS/2 mouse device common for all mice
[    1.108202] i2c /dev entries driver
[    1.115046] zynq-edac f8006000.ps7-ddrc: ecc not enabled
[    1.120561] cpufreq_cpu0: failed to get cpu0 regulator: -19
[    1.126432] Xilinx Zynq CpuIdle Driver started
[    1.131310] sdhci: Secure Digital Host Controller Interface driver
[    1.137490] sdhci: Copyright(c) Pierre Ossman
[    1.141758] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.148582] mmc0: no vqmmc regulator found
[    1.152594] mmc0: no vmmc regulator found
[    1.196692] mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
[    1.205394] usbcore: registered new interface driver usbhid
[    1.210913] usbhid: USB HID core driver
[    1.215616] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
[    1.221904] nand: Micron MT29F2G08ABAEAWP
[    1.225879] nand: 256MiB, SLC, page size: 2048, OOB size: 64
[    1.231827] Bad block table found at page 131008, version 0x01
[    1.238047] Bad block table found at page 130944, version 0x01
[    1.244043] nand_read_bbt: bad block at 0x00000c980000
[    1.249115] nand_read_bbt: bad block at 0x00000cda0000
[    1.254216] nand_read_bbt: bad block at 0x00000d040000
[    1.259368] nand_read_bbt: bad block at 0x00000d420000
[    1.264515] 3 ofpart partitions found on MTD device pl353-nand
[    1.270296] Creating 3 MTD partitions on "pl353-nand":
[    1.275407] 0x000000000000-0x000002000000 : "BOOT.bin-env-dts-kernel"
[    1.283448] 0x000002000000-0x00000b000000 : "angstram-rootfs"
[    1.290782] 0x00000b000000-0x000010000000 : "upgrade-rootfs"
[    1.299723] TCP: cubic registered
[    1.302958] NET: Registered protocol family 17
[    1.307687] Registering SWP/SWPB emulation handler
[    1.313555] regulator-dummy: disabling
[    1.317897] UBI: attaching mtd1 to ubi0
[    1.627240] UBI: scanning is finished
[    1.647818] UBI: volume 0 ("rootfs") re-sized from 192 to 1108 LEBs
[    1.654885] UBI: attached mtd1 (name "angstram-rootfs", size 144 MiB) to ubi0
[    1.661961] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    1.668725] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    1.675388] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
[    1.682266] UBI: good PEBs: 1152, bad PEBs: 0, corrupted PEBs: 0
[    1.688247] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
[    1.695355] UBI: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 1984962504
[    1.704397] UBI: available PEBs: 0, total reserved PEBs: 1152, PEBs reserved for bad PEB handling: 40
[    1.713614] UBI: background thread "ubi_bgt0d" started, PID 1080
[    1.713619] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[    1.717587] ALSA device list:
[    1.717590]   No soundcards found.
[    1.736144] UBIFS: background thread "ubifs_bgt0_0" started, PID 1082
[    1.868217] UBIFS: mounted UBI device 0, volume 0, name "rootfs"
[    1.874143] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[    1.883275] UBIFS: FS size: 128626688 bytes (122 MiB, 1013 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
[    1.893159] UBIFS: reserved for root: 0 bytes (0 KiB)
[    1.898199] UBIFS: media format: w4/r0 (latest is w4/r0), UUID 56FDF5FA-8D29-4AA7-95D4-1C2E28C7C4E9, small LPT model
[    1.961061] VFS: Mounted root (ubifs filesystem) on device 0:11.
[    2.027688] devtmpfs: mounted
[    2.030793] Freeing unused kernel memory: 204K (c06d2000 - c0705000)
[    3.342769] random: dd urandom read with 0 bits of entropy available
[    3.956690]
[    3.956690] bcm54xx_config_init
[    4.736706]
[    4.736706] bcm54xx_config_init
[    7.737556] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[    7.743649] xemacps e000b000.ps7-ethernet: link up (100/FULL)
[   38.397219] In axi fpga driver!
[   38.400287] request_mem_region OK!
[   38.403677] AXI fpga dev virtual address is 0xdf9fc000
[   38.408822] *base_vir_addr = 0x8c510
[   38.423963] In fpga mem driver!
[   38.427348] request_mem_region OK!
[   38.430854] fpga mem virtual address is 0xe2000000
[   39.186701]
[   39.186701] bcm54xx_config_init
[   39.816690]
[   39.816690] bcm54xx_config_init
[   42.817539] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[   42.823575] xemacps e000b000.ps7-ethernet: link up (100/FULL)
[  182.986723] random: nonblocking pool is initialized
Detect 512MB control board of XILINX
Miner Type = S9
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x0000ffff
Check chain[5] PIC fw version=0x03
Check chain[6] PIC fw version=0x03
Check chain[7] PIC fw version=0x03
Fix freq=550 Chain[5] voltage_pic=6 value=940
Fix freq=550 Chain[6] voltage_pic=6 value=940
Fix freq=550 Chain[7] voltage_pic=6 value=940
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
Chain[J6] has 63 asic
Chain[J7] has 63 asic
Chain[J8] has 63 asic
Chain[J6] has no freq in PIC, set default freq=550M
Chain[J6] has no core num in PIC
Chain[J7] has no freq in PIC, set default freq=550M
Chain[J7] has no core num in PIC
Chain[J8] has no freq in PIC, set default freq=550M
Chain[J8] has no core num in PIC

Miner fix freq ...
read PIC voltage=940 on chain[5]
Chain:5 chipnum=63
Asic[ 0]:550
Asic[ 1]:550 Asic[ 2]:550 Asic[ 3]:550 Asic[ 4]:550 Asic[ 5]:550 Asic[ 6]:550 Asic[ 7]:550 Asic[ 8]:550
Asic[ 9]:550 Asic[10]:550 Asic[11]:550 Asic[12]:550 Asic[13]:550 Asic[14]:550 Asic[15]:550 Asic[16]:550
Asic[17]:550 Asic[18]:550 Asic[19]:550 Asic[20]:550 Asic[21]:550 Asic[22]:550 Asic[23]:550 Asic[24]:550
Asic[25]:550 Asic[26]:550 Asic[27]:550 Asic[28]:550 Asic[29]:550 Asic[30]:550 Asic[31]:550 Asic[32]:550
Asic[33]:550 Asic[34]:550 Asic[35]:550 Asic[36]:550 Asic[37]:550 Asic[38]:550 Asic[39]:550 Asic[40]:550
Asic[41]:550 Asic[42]:550 Asic[43]:550 Asic[44]:550 Asic[45]:550 Asic[46]:550 Asic[47]:550 Asic[48]:550
Asic[49]:550 Asic[50]:550 Asic[51]:550 Asic[52]:550 Asic[53]:550 Asic[54]:550 Asic[55]:550 Asic[56]:550
Asic[57]:550 Asic[58]:550 Asic[59]:550 Asic[60]:550 Asic[61]:550 Asic[62]:550
Chain:5 max freq=550
Chain:5 min freq=550

read PIC voltage=940 on chain[6]
Chain:6 chipnum=63
Asic[ 0]:550
Asic[ 1]:550 Asic[ 2]:550 Asic[ 3]:550 Asic[ 4]:550 Asic[ 5]:550 Asic[ 6]:550 Asic[ 7]:550 Asic[ 8]:550
Asic[ 9]:550 Asic[10]:550 Asic[11]:550 Asic[12]:550 Asic[13]:550 Asic[14]:550 Asic[15]:550 Asic[16]:550
Asic[17]:550 Asic[18]:550 Asic[19]:550 Asic[20]:550 Asic[21]:550 Asic[22]:550 Asic[23]:550 Asic[24]:550
Asic[25]:550 Asic[26]:550 Asic[27]:550 Asic[28]:550 Asic[29]:550 Asic[30]:550 Asic[31]:550 Asic[32]:550
Asic[33]:550 Asic[34]:550 Asic[35]:550 Asic[36]:550 Asic[37]:550 Asic[38]:550 Asic[39]:550 Asic[40]:550
Asic[41]:550 Asic[42]:550 Asic[43]:550 Asic[44]:550 Asic[45]:550 Asic[46]:550 Asic[47]:550 Asic[48]:550
Asic[49]:550 Asic[50]:550 Asic[51]:550 Asic[52]:550 Asic[53]:550 Asic[54]:550 Asic[55]:550 Asic[56]:550
Asic[57]:550 Asic[58]:550 Asic[59]:550 Asic[60]:550 Asic[61]:550 Asic[62]:550
Chain:6 max freq=550
Chain:6 min freq=550

read PIC voltage=940 on chain[7]
Chain:7 chipnum=63
Asic[ 0]:550
Asic[ 1]:550 Asic[ 2]:550 Asic[ 3]:550 Asic[ 4]:550 Asic[ 5]:550 Asic[ 6]:550 Asic[ 7]:550 Asic[ 8]:550
Asic[ 9]:550 Asic[10]:550 Asic[11]:550 Asic[12]:550 Asic[13]:550 Asic[14]:550 Asic[15]:550 Asic[16]:550
Asic[17]:550 Asic[18]:550 Asic[19]:550 Asic[20]:550 Asic[21]:550 Asic[22]:550 Asic[23]:550 Asic[24]:550
Asic[25]:550 Asic[26]:550 Asic[27]:550 Asic[28]:550 Asic[29]:550 Asic[30]:550 Asic[31]:550 Asic[32]:550
Asic[33]:550 Asic[34]:550 Asic[35]:550 Asic[36]:550 Asic[37]:550 Asic[38]:550 Asic[39]:550 Asic[40]:550
Asic[41]:550 Asic[42]:550 Asic[43]:550 Asic[44]:550 Asic[45]:550 Asic[46]:550 Asic[47]:550 Asic[48]:550
Asic[49]:550 Asic[50]:550 Asic[51]:550 Asic[52]:550 Asic[53]:550 Asic[54]:550 Asic[55]:550 Asic[56]:550
Asic[57]:550 Asic[58]:550 Asic[59]:550 Asic[60]:550 Asic[61]:550 Asic[62]:550
Chain:7 max freq=550
Chain:7 min freq=550

max freq = 550
set baud=2
Chain[J6] PIC temp offset=62,0,0,0,0,0,38,28
Chain[J6] chip[244] use PIC middle temp offset=0 typeID=00
Warning: Chain[J6] has no temp offset in PIC! will fix it
New offset Chain[5] chip[244] local:-64 remote:0 offset:-42
Chain[J6] chip[244] get middle temp offset=-42 typeID=00
Chain[J7] PIC temp offset=62,0,0,0,0,0,38,28
Chain[J7] chip[244] use PIC middle temp offset=0 typeID=00
Warning: Chain[J7] has no temp offset in PIC! will fix it
New offset Chain[6] chip[244] local:-64 remote:0 offset:-42
Chain[J7] chip[244] get middle temp offset=-42 typeID=00
Chain[J8] PIC temp offset=62,0,0,0,0,0,38,28
Chain[J8] chip[244] use PIC middle temp offset=0 typeID=00
Warning: Chain[J8] has no temp offset in PIC! will fix it
New offset Chain[7] chip[244] local:-64 remote:0 offset:-42
Chain[J8] chip[244] get middle temp offset=-42 typeID=00
Chain[J6] set working voltage=940 [6]
Chain[J7] set working voltage=940 [6]
Chain[J8] set working voltage=940 [6]
setStartTimePoint total_tv_start_sys=1387 total_tv_end_sys=1388
restartNum = 2 , auto-reinit enabled...
do read_temp_func once...
do check_asic_reg 0x08

get RT hashrate from Chain[5]: (asic index start from 1-63)
Asic[01]=0.00000 Asic[02]=0.00000 Asic[03]=0.00000 Asic[04]=0.00000 Asic[05]=0.00000 Asic[06]=0.00000 Asic[07]=0.00000 Asic[08]=0.00000
Asic[09]=0.00000 Asic[10]=0.00000 Asic[11]=0.00000 Asic[12]=0.00000 Asic[13]=0.00000 Asic[14]=0.00000 Asic[15]=0.00000 Asic[16]=0.00000
Asic[17]=0.00000 Asic[18]=0.00000 Asic[19]=0.00000 Asic[20]=0.00000 Asic[21]=0.00000 Asic[22]=0.00000 Asic[23]=0.00000 Asic[24]=0.00000
Asic[25]=0.00000 Asic[26]=0.00000 Asic[27]=0.00000 Asic[28]=0.00000 Asic[29]=29.6110 Asic[30]=0.00000 Asic[31]=0.00000 Asic[32]=0.00000
Asic[33]=0.00000 Asic[34]=0.00000 Asic[35]=0.00000 Asic[36]=0.00000 Asic[37]=0.00000 Asic[38]=0.00000 Asic[39]=0.00000 Asic[40]=0.00000
Asic[41]=0.00000 Asic[42]=0.00000 Asic[43]=0.00000 Asic[44]=0.00000 Asic[45]=0.00000 Asic[46]=0.00000 Asic[47]=0.00000 Asic[48]=0.00000
Asic[49]=0.00000 Asic[50]=0.00000 Asic[51]=0.00000 Asic[52]=0.00000 Asic[53]=0.00000 Asic[54]=0.00000 Asic[55]=0.00000 Asic[56]=0.00000
Asic[57]=28.0010 Asic[58]=0.00000 Asic[59]=0.00000 Asic[60]=0.00000 Asic[61]=0.00000 Asic[62]=0.00000 Asic[63]=0.00000

get RT hashrate from Chain[6]: (asic index start from 1-63)
Asic[01]=0.00000 Asic[02]=0.00000 Asic[03]=0.00000 Asic[04]=0.00000 Asic[05]=0.00000 Asic[06]=0.00000 Asic[07]=0.00000 Asic[08]=0.00000
Asic[09]=0.00000 Asic[10]=0.00000 Asic[11]=0.00000 Asic[12]=0.00000 Asic[13]=0.00000 Asic[14]=0.00000 Asic[15]=0.00000 Asic[16]=0.00000
Asic[17]=0.00000 Asic[18]=0.00000 Asic[19]=0.00000 Asic[20]=0.00000 Asic[21]=0.00000 Asic[22]=0.00000 Asic[23]=0.00000 Asic[24]=0.00000
Asic[25]=0.00000 Asic[26]=0.00000 Asic[27]=0.00000 Asic[28]=0.00000 Asic[29]=27.7490 Asic[30]=0.00000 Asic[31]=0.00000 Asic[32]=0.00000
Asic[33]=0.00000 Asic[34]=0.00000 Asic[35]=0.00000 Asic[36]=0.00000 Asic[37]=0.00000 Asic[38]=0.00000 Asic[39]=0.00000 Asic[40]=0.00000
Asic[41]=0.00000 Asic[42]=0.00000 Asic[43]=0.00000 Asic[44]=0.00000 Asic[45]=0.00000 Asic[46]=0.00000 Asic[47]=0.00000 Asic[48]=0.00000
Asic[49]=0.00000 Asic[50]=0.00000 Asic[51]=0.00000 Asic[52]=0.00000 Asic[53]=0.00000 Asic[54]=0.00000 Asic[55]=0.00000 Asic[56]=0.00000
Asic[57]=26.2390 Asic[58]=0.00000 Asic[59]=0.00000 Asic[60]=0.00000 Asic[61]=0.00000 Asic[62]=0.00000 Asic[63]=0.00000

get RT hashrate from Chain[7]: (asic index start from 1-63)
Asic[01]=0.00000 Asic[02]=0.00000 Asic[03]=0.00000 Asic[04]=0.00000 Asic[05]=0.00000 Asic[06]=0.00000 Asic[07]=0.00000 Asic[08]=0.00000
Asic[09]=0.00000 Asic[10]=0.00000 Asic[11]=0.00000 Asic[12]=0.00000 Asic[13]=0.00000 Asic[14]=0.00000 Asic[15]=0.00000 Asic[16]=0.00000
Asic[17]=0.00000 Asic[18]=0.00000 Asic[19]=0.00000 Asic[20]=0.00000 Asic[21]=0.00000 Asic[22]=0.00000 Asic[23]=0.00000 Asic[24]=0.00000
Asic[25]=0.00000 Asic[26]=0.00000 Asic[27]=0.00000 Asic[28]=0.00000 Asic[29]=24.3770 Asic[30]=0.00000 Asic[31]=0.00000 Asic[32]=0.00000
Asic[33]=0.00000 Asic[34]=0.00000 Asic[35]=0.00000 Asic[36]=0.00000 Asic[37]=0.00000 Asic[38]=0.00000 Asic[39]=0.00000 Asic[40]=0.00000
Asic[41]=0.00000 Asic[42]=0.00000 Asic[43]=0.00000 Asic[44]=0.00000 Asic[45]=0.00000 Asic[46]=0.00000 Asic[47]=0.00000 Asic[48]=0.00000
Asic[49]=0.00000 Asic[50]=0.00000 Asic[51]=0.00000 Asic[52]=0.00000 Asic[53]=0.00000 Asic[54]=0.00000 Asic[55]=0.00000 Asic[56]=0.00000
Asic[57]=23.0510 Asic[58]=0.00000 Asic[59]=0.00000 Asic[60]=0.00000 Asic[61]=0.00000 Asic[62]=0.00000 Asic[63]=0.00000
Check Chain[J6] ASIC RT error: (asic index start from 1-63)
Check Chain[J7] ASIC RT error: (asic index start from 1-63)
Check Chain[J8] ASIC RT error: (asic index start from 1-63)
Done check_asic_reg
do read temp on Chain[5]
Chain[5] Chip[62] TempTypeID=00 middle offset=-42
read failed, old value: Chain[5] Chip[62] local Temp=0
read failed on Chain[5] Chip[62] middle Temp old value:0
Done read temp on Chain[5]
do read temp on Chain[6]
Chain[6] Chip[62] TempTypeID=00 middle offset=-42
read failed, old value: Chain[6] Chip[62] local Temp=0
read failed on Chain[6] Chip[62] middle Temp old value:0
Done read temp on Chain[6]
do read temp on Chain[7]
Chain[7] Chip[62] TempTypeID=00 middle offset=-42
read failed, old value: Chain[7] Chip[62] local Temp=0
read failed on Chain[7] Chip[62] middle Temp old value:0
Done read temp on Chain[7]
set FAN speed according to: temp_highest=0 temp_top1[PWM_T]=0 temp_top1[TEMP_POS_LOCAL]=0 temp_change=0 fix_fan_steps=0
set full FAN speed...
FAN PWM: 100
read_temp_func Done!
CRC error counter=3

Code:
Check Chain[J6] ASIC RT error: (asic index start from 1-63)
Check Chain[J7] ASIC RT error: (asic index start from 1-63)
Check Chain[J8] ASIC RT error: (asic index start from 1-63)
Done check_asic_reg
do read temp on Chain[5]
Chain[5] Chip[62] TempTypeID=00 middle offset=-42
read failed, old value: Chain[5] Chip[62] local Temp=0
read failed on Chain[5] Chip[62] middle Temp old value:0
Done read temp on Chain[5]
do read temp on Chain[6]
Chain[6] Chip[62] TempTypeID=00 middle offset=-42
read failed, old value: Chain[6] Chip[62] local Temp=0
read failed on Chain[6] Chip[62] middle Temp old value:0
Done read temp on Chain[6]
do read temp on Chain[7]
Chain[7] Chip[62] TempTypeID=00 middle offset=-42
read failed, old value: Chain[7] Chip[62] local Temp=0
read failed on Chain[7] Chip[62] middle Temp old value:0
Done read temp on Chain[7]
set FAN speed according to: temp_highest=0 temp_top1[PWM_T]=0 temp_top1[TEMP_POS_LOCAL]=0 temp_change=0 fix_fan_steps=0
set full FAN speed...
FAN PWM: 100
read_temp_func Done!
CRC error counter=3
rymannphilippe
Newbie
*
Offline Offline

Activity: 5
Merit: 0


View Profile
April 20, 2018, 07:53:37 AM
 #7

Did you install the new Update from BITMAIN Website?

-->--> Antminer-S9-all-201711171757-autofreq-user-Update2UBI-NF.tar.gz


Looks like you installed a fixed frequency.
Try the "AUTOFREQ" firmware.
fanatic26
Hero Member
*****
Offline Offline

Activity: 756
Merit: 560


View Profile
April 20, 2018, 03:06:49 PM
 #8

-->--> Antminer-S9-all-201711171757-autofreq-user-Update2UBI-NF.tar.gz


Do NOT use this firmware. Use an older version from the Bitmain site. The 1117 firmware is well known to be buggy and problem prone.

Stop buying industrial miners, running them at home, and then complaining about the noise.
tim-bc
Member
**
Offline Offline

Activity: 224
Merit: 65


View Profile
April 20, 2018, 06:05:05 PM
 #9

-->--> Antminer-S9-all-201711171757-autofreq-user-Update2UBI-NF.tar.gz
Do NOT use this firmware. Use an older version from the Bitmain site. The 1117 firmware is well known to be buggy and problem prone.
About a week ago, bitmain removed the older autofreq S9 firmware from their site. You can probably still find the file elsewhere.

File: Antminer-S9-all-201704270135-autofreq-user-Update2UBI-NF.tar.gz
SHA-1: 0515029015ad8dcedb185367fc5f829851dc65ed

Ignore scammers on Skype, Telegram, etc. I will only ever contact you via forum PMs. See profile for fingerprint.
malamama
Newbie
*
Offline Offline

Activity: 11
Merit: 0


View Profile
April 21, 2018, 05:21:30 PM
 #10

-->--> Antminer-S9-all-201711171757-autofreq-user-Update2UBI-NF.tar.gz
Do NOT use this firmware. Use an older version from the Bitmain site. The 1117 firmware is well known to be buggy and problem prone.
About a week ago, bitmain removed the older autofreq S9 firmware from their site. You can probably still find the file elsewhere.

File: Antminer-S9-all-201704270135-autofreq-user-Update2UBI-NF.tar.gz
SHA-1: 0515029015ad8dcedb185367fc5f829851dc65ed

I didn't find this firmware, anybody knows where i cand download it

best regards
BitMaxz
Legendary
*
Offline Offline

Activity: 1246
Merit: 1038

Bitmain miners is getting worst.


View Profile WWW
April 21, 2018, 08:19:39 PM
 #11

-->--> Antminer-S9-all-201711171757-autofreq-user-Update2UBI-NF.tar.gz
Do NOT use this firmware. Use an older version from the Bitmain site. The 1117 firmware is well known to be buggy and problem prone.
About a week ago, bitmain removed the older autofreq S9 firmware from their site. You can probably still find the file elsewhere.

File: Antminer-S9-all-201704270135-autofreq-user-Update2UBI-NF.tar.gz
SHA-1: 0515029015ad8dcedb185367fc5f829851dc65ed

I didn't find this firmware, anybody knows where i cand download it

best regards
Its recommended to download the firmware directly to bitmain here https://shop.bitmain.com/support.htm
If you download a firmware in the untrusted source there is possibility that you can be hack or they can remote your miner.
So I suggest you to use only the firmware from bitmain.

tim-bc
Member
**
Offline Offline

Activity: 224
Merit: 65


View Profile
April 21, 2018, 08:51:43 PM
 #12

Unless your source is fully trustworthy, you should always confirm the SHA-1 checksum to verify the integrity of any files you download.

Since the file was on Bitmain's official site until recently, you should be able to find it elsewhere.

Ignore scammers on Skype, Telegram, etc. I will only ever contact you via forum PMs. See profile for fingerprint.
Pages: [1]
  Print  
 
Jump to:  

Sponsored by , a Bitcoin-accepting VPN.
Powered by MySQL Powered by PHP Powered by SMF 1.1.19 | SMF © 2006-2009, Simple Machines Valid XHTML 1.0! Valid CSS!