[Setup & Troubleshoot] Bitmain AntMiner S1 180GH/S miner

[zamot]

Ohfercryingoutloud, I just set WAN to DCHP and now my browser cannot find the Ant. I keep getting "Oops! Google Chrome could not connect." Suggestions, anyone?

Damn hell ass distracting dogs. Heh.

Try with some IP scan tool to find your hiding Ant  .

[brush242]

Ohfercryingoutloud, I just set WAN to DCHP and now my browser cannot find the Ant. I keep getting "Oops! Google Chrome could not connect." Suggestions, anyone?

Damn hell ass distracting dogs. Heh

Try with some IP scan tool to find your hiding Ant  .

Crap, right, that's exactly right. D'oh!! Thanks!

[wolf_miner]

@brush242 look at your router config pages, usually there is a DHCP Client table.

W_M

[brush242]

@brush242 look at your router config pages, usually there is a DHCP Client table.

You're right, and thank you as well. Sometimes I amaze myself at the things I forget.

Well, not "forget," per se. Forget to check.

[snoopy_nzl]

be very careful if you order S1 via sushi-review website, if you get error you seem to be stuffed, no responses from repeated attempts to contact Josh, I certainly wont spend another cent via Bitmain tech till I get my 2 x  S1's I paid for  or BTC back, it is looking to me like a scam even though I had successfully ordered and received some units once prior how do I troubleshoot this??

[brush242]

So far, the only thing I would change is that I would add a "Start" button on the Miner Config page. I think people like to see those.

[w00tcoin]

Just ordered an AntMiner from minersource!

Can't wait to get it!

[oztusk]

Ohfercryingoutloud, I just set WAN to DCHP and now my browser cannot find the Ant. I keep getting "Oops! Google Chrome could not connect." Suggestions, anyone?

Damn hell ass distracting dogs. Heh

Try with some IP scan tool to find your hiding Ant  .

Crap, right, that's exactly right. D'oh!! Thanks!

there is a windows uility that works quite well called "advanced ip scanner"

[realnebby]

I'm having an issue keeping my AntMiner S1 up and working. More often than not when I power it up it doesn't seem to see the ASIC blades and the "AntMiner" section of the "Miner Status" page says there is no information to show. When it does see it and starts mining I get a lot of errors in the logs like what I have posted below. It seems to work for a little while and then stop and start. Sometimes it stops and starts beeping. It seems from other messages I see that the blades are connected to the main computer via USB, so these errors seem relevant. Anyone else had this issue?


[10094.940000] usb 1-1: clear tt 1 (9081) error -71
[10099.700000] usb 1-1: clear tt 1 (9081) error -71
[10101.850000] usb 1-1: clear tt 1 (9081) error -71
[10104.940000] usb 1-1: clear tt 1 (9081) error -71
[10107.080000] usb 1-1: clear tt 1 (9081) error -71
[10113.340000] usb 1-1: clear tt 1 (9081) error -71
[10115.070000] usb 1-1: clear tt 1 (9081) error -71
[10118.610000] usb 1-1: clear tt 1 (9081) error -71
[10121.960000] usb 1-1: clear tt 1 (9081) error -71
[10123.420000] usb 1-1: clear tt 1 (9081) error -71
[10128.980000] usb 1-1: clear tt 1 (9081) error -71
[10129.260000] usb 1-1: clear tt 1 (9081) error -71
[10129.720000] usb 1-1: clear tt 1 (9081) error -71
[10131.910000] usb 1-1: clear tt 1 (9081) error -71
[10135.810000] usb 1-1: clear tt 1 (9081) error -71
[10139.930000] usb 1-1: clear tt 1 (9081) error -71
[10139.980000] usb 1-1: clear tt 1 (9081) error -71
[10140.000000] usb 1-1: clear tt 1 (9081) error -71
[10140.780000] usb 1-1: clear tt 1 (9081) error -71
[10144.020000] usb 1-1: clear tt 1 (9081) error -71

[freebit13]

I'm having an issue keeping my AntMiner S1 up and working. More often than not when I power it up it doesn't seem to see the ASIC blades and the "AntMiner" section of the "Miner Status" page says there is no information to show. When it does see it and starts mining I get a lot of errors in the logs like what I have posted below. It seems to work for a little while and then stop and start. Sometimes it stops and starts beeping. It seems from other messages I see that the blades are connected to the main computer via USB, so these errors seem relevant. Anyone else had this issue?


[10094.940000] usb 1-1: clear tt 1 (9081) error -71
[10099.700000] usb 1-1: clear tt 1 (9081) error -71
[10101.850000] usb 1-1: clear tt 1 (9081) error -71
[10104.940000] usb 1-1: clear tt 1 (9081) error -71
[10107.080000] usb 1-1: clear tt 1 (9081) error -71
[10113.340000] usb 1-1: clear tt 1 (9081) error -71
[10115.070000] usb 1-1: clear tt 1 (9081) error -71
[10118.610000] usb 1-1: clear tt 1 (9081) error -71
[10121.960000] usb 1-1: clear tt 1 (9081) error -71
[10123.420000] usb 1-1: clear tt 1 (9081) error -71
[10128.980000] usb 1-1: clear tt 1 (9081) error -71
[10129.260000] usb 1-1: clear tt 1 (9081) error -71
[10129.720000] usb 1-1: clear tt 1 (9081) error -71
[10131.910000] usb 1-1: clear tt 1 (9081) error -71
[10135.810000] usb 1-1: clear tt 1 (9081) error -71
[10139.930000] usb 1-1: clear tt 1 (9081) error -71
[10139.980000] usb 1-1: clear tt 1 (9081) error -71
[10140.000000] usb 1-1: clear tt 1 (9081) error -71
[10140.780000] usb 1-1: clear tt 1 (9081) error -71
[10144.020000] usb 1-1: clear tt 1 (9081) error -71

I've not seen this problem, but I'd suggest checking that all the cables are fitted nice and snug.

[realnebby]

I'm having an issue keeping my AntMiner S1 up and working. More often than not when I power it up it doesn't seem to see the ASIC blades and the "AntMiner" section of the "Miner Status" page says there is no information to show. When it does see it and starts mining I get a lot of errors in the logs like what I have posted below. It seems to work for a little while and then stop and start. Sometimes it stops and starts beeping. It seems from other messages I see that the blades are connected to the main computer via USB, so these errors seem relevant. Anyone else had this issue?


[10094.940000] usb 1-1: clear tt 1 (9081) error -71
[10099.700000] usb 1-1: clear tt 1 (9081) error -71
[10101.850000] usb 1-1: clear tt 1 (9081) error -71
[10104.940000] usb 1-1: clear tt 1 (9081) error -71
[10107.080000] usb 1-1: clear tt 1 (9081) error -71
[10113.340000] usb 1-1: clear tt 1 (9081) error -71
[10115.070000] usb 1-1: clear tt 1 (9081) error -71
[10118.610000] usb 1-1: clear tt 1 (9081) error -71
[10121.960000] usb 1-1: clear tt 1 (9081) error -71
[10123.420000] usb 1-1: clear tt 1 (9081) error -71
[10128.980000] usb 1-1: clear tt 1 (9081) error -71
[10129.260000] usb 1-1: clear tt 1 (9081) error -71
[10129.720000] usb 1-1: clear tt 1 (9081) error -71
[10131.910000] usb 1-1: clear tt 1 (9081) error -71
[10135.810000] usb 1-1: clear tt 1 (9081) error -71
[10139.930000] usb 1-1: clear tt 1 (9081) error -71
[10139.980000] usb 1-1: clear tt 1 (9081) error -71
[10140.000000] usb 1-1: clear tt 1 (9081) error -71
[10140.780000] usb 1-1: clear tt 1 (9081) error -71
[10144.020000] usb 1-1: clear tt 1 (9081) error -71

I've not seen this problem, but I'd suggest checking that all the cables are fitted nice and snug.

I've tried that already. Thanks anyway.

[freebit13]

I've not seen this problem, but I'd suggest checking that all the cables are fitted nice and snug.

I've tried that already. Thanks anyway.

Next thing I'd try would be a hard reset and if that doesn't help, try reloading the firmware, even if you do have the latest.

[realnebby]

I've not seen this problem, but I'd suggest checking that all the cables are fitted nice and snug.

I've tried that already. Thanks anyway.

Next thing I'd try would be a hard reset and if that doesn't help, try reloading the firmware, even if you do have the latest.

By hard reset, do you mean turning off the power? Or reseting to defaults on the "Backup / Flash Firmware" tab? Where do I get the latest firmware image?

[Raptor2213]

I've not seen this problem, but I'd suggest checking that all the cables are fitted nice and snug.

I've tried that already. Thanks anyway.

Next thing I'd try would be a hard reset and if that doesn't help, try reloading the firmware, even if you do have the latest.

By hard reset, do you mean turning off the power? Or reseting to defaults on the "Backup / Flash Firmware" tab? Where do I get the latest firmware image?

A hard reset is done via the black button on the controller card.
Firmware updates: https://github.com/AntMiner/AntGen1
CGminer updates: https://github.com/kanoi/cgminer-binaries/tree/master/AntS1

[realnebby]

I've not seen this problem, but I'd suggest checking that all the cables are fitted nice and snug.

I've tried that already. Thanks anyway.

Next thing I'd try would be a hard reset and if that doesn't help, try reloading the firmware, even if you do have the latest.

By hard reset, do you mean turning off the power? Or reseting to defaults on the "Backup / Flash Firmware" tab? Where do I get the latest firmware image?

A hard reset is done via the black button on the controller card.
Firmware updates: https://github.com/AntMiner/AntGen1
CGminer updates: https://github.com/kanoi/cgminer-binaries/tree/master/AntS1

So I tried the hardreset and now I'm getting more errors like the following. Any ideas?

[  115.270000] bitmainbl 1-1.1:1.0: bitmainbl_read_int_callback - nonzero write bulk status received: -71
[  115.280000] no int in filled
[  115.400000] bitmainbl 1-1.1:1.0: bitmainbl_read_int_callback - nonzero write bulk status received: -32
[  115.410000] no int in filled
[  115.510000] bitmainbl 1-1.1:1.0: bitmainbl_read_int_callback - nonzero write bulk status received: -32
[  115.530000] no int in filled
[  115.530000] bitmainbl 1-1.1:1.0: bitmainbl_read_int_callback - nonzero write bulk status received: -32
[  115.540000] no int in filled
[  115.570000] bitmainbl 1-1.1:1.0: bitmainbl_read_int_callback - nonzero write bulk status received: -32
[  115.590000] no int in filled
[  115.690000] bitmainbl 1-1.1:1.0: bitmainbl_read_int_callback - nonzero write bulk status received: -71
[  115.700000] no int in filled
[  115.740000] bitmainbl 1-1.1:1.0: bitmainbl_read_int_callback - nonzero write bulk status received: -32
[  115.750000] no int in filled
[  115.750000] bitmainbl 1-1.1:1.0: bitmainbl_read_int_callback - nonzero write bulk status received: -32
[  115.770000] no int in filled
[  115.770000] bitmainbl 1-1.1:1.0: bitmainbl_read_int_callback - nonzero write bulk status received: -32
[  115.780000] no int in filled
[  115.860000] bitmainbl 1-1.1:1.0: bitmainbl_read_int_callback - nonzero write bulk status received: -32
[  115.880000] no int in filled
[  115.880000] bitmainbl 1-1.1:1.0: bitmainbl_read_int_callback - nonzero write bulk status received: -32
[  115.890000] no int in filled
[  115.890000] bitmainbl 1-1.1:1.0: bitmainbl_read_int_callback - nonzero write bulk status received: -32
[  115.910000] no int in filled

[realnebby]

I've not seen this problem, but I'd suggest checking that all the cables are fitted nice and snug.

I've tried that already. Thanks anyway.

Next thing I'd try would be a hard reset and if that doesn't help, try reloading the firmware, even if you do have the latest.

By hard reset, do you mean turning off the power? Or reseting to defaults on the "Backup / Flash Firmware" tab? Where do I get the latest firmware image?

A hard reset is done via the black button on the controller card.
Firmware updates: https://github.com/AntMiner/AntGen1
CGminer updates: https://github.com/kanoi/cgminer-binaries/tree/master/AntS1

So I tried the hardreset and now I'm getting more errors like the following. Any ideas?

[  115.270000] bitmainbl 1-1.1:1.0: bitmainbl_read_int_callback - nonzero write bulk status received: -71
[  115.280000] no int in filled
[  115.400000] bitmainbl 1-1.1:1.0: bitmainbl_read_int_callback - nonzero write bulk status received: -32
[  115.410000] no int in filled
[  115.510000] bitmainbl 1-1.1:1.0: bitmainbl_read_int_callback - nonzero write bulk status received: -32
[  115.530000] no int in filled
[  115.530000] bitmainbl 1-1.1:1.0: bitmainbl_read_int_callback - nonzero write bulk status received: -32
[  115.540000] no int in filled
[  115.570000] bitmainbl 1-1.1:1.0: bitmainbl_read_int_callback - nonzero write bulk status received: -32
[  115.590000] no int in filled
[  115.690000] bitmainbl 1-1.1:1.0: bitmainbl_read_int_callback - nonzero write bulk status received: -71
[  115.700000] no int in filled
[  115.740000] bitmainbl 1-1.1:1.0: bitmainbl_read_int_callback - nonzero write bulk status received: -32
[  115.750000] no int in filled
[  115.750000] bitmainbl 1-1.1:1.0: bitmainbl_read_int_callback - nonzero write bulk status received: -32
[  115.770000] no int in filled
[  115.770000] bitmainbl 1-1.1:1.0: bitmainbl_read_int_callback - nonzero write bulk status received: -32
[  115.780000] no int in filled
[  115.860000] bitmainbl 1-1.1:1.0: bitmainbl_read_int_callback - nonzero write bulk status received: -32
[  115.880000] no int in filled
[  115.880000] bitmainbl 1-1.1:1.0: bitmainbl_read_int_callback - nonzero write bulk status received: -32
[  115.890000] no int in filled
[  115.890000] bitmainbl 1-1.1:1.0: bitmainbl_read_int_callback - nonzero write bulk status received: -32
[  115.910000] no int in filled

I've also now tried re-flashing the lastest firmware and reseting to factory settings and still seeing the above errors.

Does anyone have any experience with activating BitMain's warranty replacement?

[LanMachine]

ship the broken device to bitmain back if you within 90 days of waranty!

i had a problem with the lan adapter on my device and this was a communication with bitmain support!

Hi Dimitri,

please just ship back the bad parts to bellow address, and mark your name and order ID in the package.Â
----------------------------------------------------------------------
Building No.13-16, Jiu Wei New Village, Xixiang Street, BaoAn District, Shenzhen, 518126, China

Contact: Gao JianPing

----------------------------------------------------------------------

please share us your tracking number after you ship out, when we receive it, we will re-ship good replacement to you.


Best Regards

 

BITMAIN

[wurzelsepp82]

hi all,

how can i configure the S1 to shutdown if a critical temperature reaches ...
i dont trust the units and i cant watch them 24/7 .

there is a command --bitmain-temp  but how can i use it?
I cant find anything at the webinterface.


thx
Wurzelsepp

[J_Dubbs]

hi all,

how can i configure the S1 to shutdown if a critical temperature reaches ...
i dont trust the units and i cant watch them 24/7 .

there is a command --bitmain-temp  but how can i use it?
I cant find anything at the webinterface.


thx
Wurzelsepp

I don't have an answer but what is considered "critical temperature"? Weather is getting warm here and mine are running at 47c... I might add a fan pulling from the front, but the most recommended brand seems discontinued.

[J_Dubbs]

Is this fan good for the front of these? (Ie, to pull air from opposite side of OEM fan)

http://www.newegg.com/Product/Product.aspx?Item=N82E16835705040

From what I've seen this looks like good bang for the buck, right?