Sitaga (OP)
Newbie
 Offline
Activity: 14
Merit: 0
|
 |
December 16, 2013, 06:55:46 PM |
|
Do X's in the cube web console mean the chip is bad?
When I first got the unit there was only 1 X on the last blade listed (M_81-96), now there are 8 new Xs on M_65-80. Does this indicate that I need a blade (or the entire cube) replaced?
What does the red "Status" led indicate? I have two cubes - both have this status light blinking irradically, however they both seem to blink at the same time.
Thanks for the help!
Sitaga
|
|
|
|
|
|
|
|
|
|
|
|
Bitcoin addresses contain a checksum, so it is very unlikely that mistyping an address will cause you to lose money.
|
|
|
Advertised sites are not endorsed by the Bitcoin Forum. They may be unsafe, untrustworthy, or illegal in your jurisdiction.
|
|
|
|
|
|
empoweoqwj
|
|
December 17, 2013, 09:35:07 AM |
|
Do X's in the cube web console mean the chip is bad?
When I first got the unit there was only 1 X on the last blade listed (M_81-96), now there are 8 new Xs on M_65-80. Does this indicate that I need a blade (or the entire cube) replaced?
What does the red "Status" led indicate? I have two cubes - both have this status light blinking irradically, however they both seem to blink at the same time.
Thanks for the help!
Sitaga
I would suggest getting support from whoever sold you the cube. |
|
|
|
|
|
HellDiverUK
|
|
December 17, 2013, 03:34:25 PM |
|
The mini-blades come loose in shipping. Try reseating them.
|
|
|
|
|
Sitaga (OP)
Newbie
Offline
Activity: 14
Merit: 0
|
|
December 17, 2013, 03:59:59 PM |
|
I've sent them a message as well. No reply so far, but I'm sure they will get back to me. Been good on all other purchases in the past. Thanks!
I don't want to open the case and re-seat until after I talk to them.
|
|
|
|
|
|
dentldir
|
|
December 17, 2013, 04:18:38 PM |
|
Its also likely that the cube is running too hot.
|
1DentLdiRMv3dpmpmqWsQev8BUaty9vN3v
|
|
|
|
empoweoqwj
|
|
December 17, 2013, 05:21:45 PM |
|
I've sent them a message as well. No reply so far, but I'm sure they will get back to me. Been good on all other purchases in the past. Thanks!
I don't want to open the case and re-seat until after I talk to them.
Is there no manual saying what the lights mean? Or is it in Chinese?  |
|
|
|
|
Sitaga (OP)
Newbie
Offline
Activity: 14
Merit: 0
|
|
December 17, 2013, 06:29:05 PM |
|
No manual included..  |
|
|
|
|
Sitaga (OP)
Newbie
Offline
Activity: 14
Merit: 0
|
|
December 17, 2013, 10:37:32 PM |
|
Some news to report. All the Xs are gone (even the original single X from the beginning).
All I did was run an extension cord to the cube from a different circuit in the house (about 20' away). Previously it was connect to a battery backup (surge side) that my computer uses.
Its now hashing at 32GH/s in Low. I haven't tried High yet.
The status light still blinks whenever and however it wants, but o'well.
|
|
|
|
|
sidehack
Legendary
Offline
Activity: 3318
Merit: 1848
Curmudgeonly hardware guy
|
|
December 18, 2013, 07:12:47 AM |
|
A blinking status light is a good thing, lets you know it's busily hashing away.
Have you slid the boards out and checked for loose heatsinks?
|
|
|
|
|
empoweoqwj
|
|
December 18, 2013, 07:15:25 AM |
|
A blinking status light is a good thing, lets you know it's busily hashing away.
Have you slid the boards out and checked for loose heatsinks?
Yes that's right, the status light blinking is a good thing. |
|
|
|
|
Sitaga (OP)
Newbie
Offline
Activity: 14
Merit: 0
|
|
December 18, 2013, 11:56:42 AM |
|
No, I haven't slid it apart - but everything is working good now that I moved power. Still have 32ghs each.
|
|
|
|
|
|
HellDiverUK
|
|
December 18, 2013, 11:59:24 AM |
|
These things are REALLY picky about power supplies. Mine wouldn't run off my Corsair CX750. It does run off an old Dell 875W PSU.
There's lots of info in the thread in Custom Hardware about PSUs.
|
|
|
|
|
Sitaga (OP)
Newbie
Offline
Activity: 14
Merit: 0
|
|
December 18, 2013, 07:00:55 PM |
|
Ahh. but I didn't switch PSUs.. just the break (plug) in my house. Even stranger, huh?
|
|
|
|
|
chonce
Newbie
Offline
Activity: 4
Merit: 0
|
|
December 30, 2013, 08:54:46 AM |
|
The mini-blades come loose in shipping. Try reseating them.
Agree this
|
|
|
|
|
|
empoweoqwj
|
|
December 30, 2013, 09:18:24 AM |
|
No, I haven't slid it apart - but everything is working good now that I moved power. Still have 32ghs each.
Is 32 Gh/s what they are supposed to hash at? |
|
|
|
|
|
HellDiverUK
|
|
December 30, 2013, 09:44:11 AM |
|
Mine does 38.5GH in High. When it works. It's still a bit fussy about power, but it's mostly stable on a 600W OCZ PSU.
|
|
|
|
|
|
empoweoqwj
|
|
December 30, 2013, 09:53:09 AM |
|
Mine does 38.5GH in High. When it works. It's still a bit fussy about power, but it's mostly stable on a 600W OCZ PSU.
Ah ok. Just re-read and the OP said his was doing 32GH in 'low' so its running ok |
|
|
|
|
|
