mritter0
Newbie
Offline
Activity: 8
Merit: 2
|
|
March 18, 2024, 10:03:41 PM |
|
Now I hooked my R909 up to my PC. Replaced the drivers. Edited the start-r909.bat file with my BTC address. Double clicked it, cmd window opens, cgminer started, no output.
I have an ASUS RT-AX86U Pro router. Could it be blocking everything?
Grabbing at straws here.
|
|
|
|
|
|
|
|
|
Each block is stacked on top of the previous one. Adding another block to the top makes all lower blocks more difficult to remove: there is more "weight" above each block. A transaction in a block 6 blocks deep (6 confirmations) will be very difficult to remove.
|
|
|
Advertised sites are not endorsed by the Bitcoin Forum. They may be unsafe, untrustworthy, or illegal in your jurisdiction.
|
|
|
|
IAmGPIO
Jr. Member
Offline
Activity: 31
Merit: 10
|
|
March 19, 2024, 11:11:31 AM |
|
Now I hooked my R909 up to my PC. Replaced the drivers. Edited the start-r909.bat file with my BTC address. Double clicked it, cmd window opens, cgminer started, no output.
I have an ASUS RT-AX86U Pro router. Could it be blocking everything?
Grabbing at straws here.
Hey, DM me on Discord - I will help you sort this. i will then report back here with findings to help future issues.
|
|
|
|
IAmGPIO
Jr. Member
Offline
Activity: 31
Merit: 10
|
|
March 19, 2024, 11:29:25 PM |
|
New firmware available. Check the 4th post down on this thread.
|
|
|
|
mritter0
Newbie
Offline
Activity: 8
Merit: 2
|
|
March 19, 2024, 11:59:42 PM |
|
I got my connection issues figured out.
ASUS RT-AX86U Pro router AiProtection Two-Way IPS -> Off
It says right in the description that it blocks Bitcoin Mining. Disabling this cured the issue immediately.
Thanks to all the guys who helped me figure this out and with some other newbie questions.
|
|
|
|
gt_addict
|
|
March 20, 2024, 11:29:20 AM |
|
New firmware available. Check the 4th post down on this thread.
I’m going to assume you need to put the details in again for miners, freq, pool details (if different from default)?
|
**SUPPORT SIDEHACK** Miner Development Donations to: 1BURGERAXHH6Yi6LRybRJK7ybEm5m5HwTr
Donations/Tips to:- 1GTADDicTXD1uachKKgW24DZDxDGhSMdRa
Join Bitconnect: https://bitconnect.co/?ref=gtaddict
|
|
|
IAmGPIO
Jr. Member
Offline
Activity: 31
Merit: 10
|
|
March 20, 2024, 01:11:47 PM |
|
New firmware available. Check the 4th post down on this thread.
I’m going to assume you need to put the details in again for miners, freq, pool details (if different from default)? Yes, it's a whole new image and resets everything to factory. This is not a critical update so if your system is working and you're happy, leave it!
|
|
|
|
mritter0
Newbie
Offline
Activity: 8
Merit: 2
|
|
March 20, 2024, 08:12:24 PM |
|
New firmware available. Check the 4th post down on this thread.
I’m going to assume you need to put the details in again for miners, freq, pool details (if different from default)? Yes, it's a whole new image and resets everything to factory. This is not a critical update so if your system is working and you're happy, leave it! What about changing the pool url gadget to a drop-down box with 3 (or more) default options: ckpool solo KanoPool Custom Then a text gadget to enter a custom/modified pool.
|
|
|
|
mritter0
Newbie
Offline
Activity: 8
Merit: 2
|
|
March 20, 2024, 11:56:56 PM |
|
Keep the initial setup simple as it is now. But.....
Add some more settings to the System Config page?
I am sure everyone that mines wants to set their miners to certain IP addresses. DHCP is not working the way I want. I set an assigned IP in my router but the hub is still using the original one it was assigned. I did a system reboot, put the wrong wifi password in on purpose, it still set it to the old IP. It seems to be "stuck".
Add a Workers page with a list and stats of each miner. Easier to see if one is not working properly. 01. R909 100050786 2.142Th 550 etc Red is in error, yellow if warning 02. R909 100xxxxxx 2.201Th 550 etc 03. Compaq F 200346543 350Gh 450 .... 10. R909
Total hash rate in large font.
Plenty of room for more stats/details.
|
|
|
|
IAmGPIO
Jr. Member
Offline
Activity: 31
Merit: 10
|
|
March 21, 2024, 12:46:21 AM |
|
Keep the initial setup simple as it is now. But.....
Add some more settings to the System Config page?
I am sure everyone that mines wants to set their miners to certain IP addresses. DHCP is not working the way I want. I set an assigned IP in my router but the hub is still using the original one it was assigned. I did a system reboot, put the wrong wifi password in on purpose, it still set it to the old IP. It seems to be "stuck".
Add a Workers page with a list and stats of each miner. Easier to see if one is not working properly. 01. R909 100050786 2.142Th 550 etc Red is in error, yellow if warning 02. R909 100xxxxxx 2.201Th 550 etc 03. Compaq F 200346543 350Gh 450 .... 10. R909
Total hash rate in large font.
Plenty of room for more stats/details.
if you want to define a static IP on the SmartHub, edit the /etc/dhcpcd.conf file and define your static IP. Dont assign it in the router, assign it on the Hub itself. All of the stat' bits you mention will all come in due course, embedded in the SmartHub Gui. This is one of the reasons I linked Kano's stats page directly from the SmartHub UI, to give people the extra stats you describe in the meantime.
|
|
|
|
|
philipma1957
Legendary
Online
Activity: 4116
Merit: 7824
'The right to privacy matters'
|
|
April 14, 2024, 10:22:07 PM |
|
People have asked, as I did, how many R909s can the SmartHub handle? I have 8 with plans to get 3 more to use all 11 USB ports. I am using it with an EVGA 1600W PSU that has 9 VGA ports and with special cables, use the 2 CPU ports. Since there is plenty of CPU and RAM available, maybe a USB hub will give a few more R909 slots, with an additional PSU to power them. here are your photos
|
|
|
|
|