HELP - Antminer S9 - Shows no speed after running for 3 minutes ???

[Dragonizer]

Hi All

I have about x15 S9's and have run them for years BUT i am having a problem with a 13.5Th one...

It runs for 2 or 3 mins, all temps perfect, fan speeds OK, no dodgy boards/chips. (temps in the med/high 70's)

The speed just goes to 0Gh ??

I have tried rebooting, i also reflashed the auto Freq FW and also i have tried the 600Mhz fixed FW...But it still just stops after 2/3 mins ??

I have also tried DHCP....

Anyone got any ideas, its only 2 months old.

Thanks in advance for any reply...

[1713531438]

1713531438

[1713531438]

1713531438

[1713531438]

1713531438

[1713531438]

1713531438

[BitMaxz]

Can you post your kernel logs here or copy-paste it to https://pastebin.com and put it here.

Sometimes the problem is a fan so if one of your fans is damaged the miner will work for a while then stop.

You can try to replace the fan cable or replace it with a new working fan, but first, troubleshoot the problem which fan is damaged if it's the intake or the exhaust fan.

[Dragonizer]

Can you post your kernel logs here or copy-paste it to https://pastebin.com and put it here.

Sometimes the problem is a fan so if one of your fans is damaged the miner will work for a while then stop.

You can try to replace the fan cable or replace it with a new working fan, but first, troubleshoot the problem which fan is damaged if it's the intake or the exhaust fan.

I've replaced 40 odd fan's over the years....It's not that.

It's running on 2 Boards AND the disconnected board id no.6/No3/No.3 from opposite the PCB supply

It has NEVER shown high temps, never had a problem BUT why now ?
I will post a log, there MUST be some analogy there ?

Cheers

[Dragonizer]

EDIT -Just plugged third board back in ( On EVERY miner fail/overtemp it is board 3 or chain 8 !!!! NOT 6 AS I STATED ABOVE, same thing)
Temps are stable at 61,56,69.

LOG-

Code:

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 3.14.0-xilinx-gb190cb0-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #57 SMP PREEMPT Fri Dec 9 14:49:22 CST 2016
[    0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine model: Xilinx Zynq
[    0.000000] cma: CMA: reserved 128 MiB at 16800000
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] On node 0 totalpages: 126976
[    0.000000] free_area_init_node: node 0, pgdat c0740a40, node_mem_map debd8000
[    0.000000]   Normal zone: 992 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 126976 pages, LIFO batch:31
[    0.000000] PERCPU: Embedded 8 pages/cpu @debc1000 s9088 r8192 d15488 u32768
[    0.000000] pcpu-alloc: s9088 r8192 d15488 u32768 alloc=8*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 125984
[    0.000000] Kernel command line: noinitrd mem=496M console=ttyPS0,115200 root=ubi0:rootfs ubi.mtd=1 rootfstype=ubifs rw rootwait
[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Memory: 364356K/507904K available (5032K kernel code, 283K rwdata, 1916K rodata, 204K init, 258K bss, 143548K reserved, 0K highmem)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xdf800000 - 0xff000000   ( 504 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xdf000000   ( 496 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc06d1374   (6949 kB)
[    0.000000]       .init : 0xc06d2000 - 0xc0705380   ( 205 kB)
[    0.000000]       .data : 0xc0706000 - 0xc074cf78   ( 284 kB)
[    0.000000]        .bss : 0xc074cf84 - 0xc078d9fc   ( 259 kB)
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] 	Dump stacks of tasks blocking RCU-preempt GP.
[    0.000000] 	RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] ps7-slcr mapped to df802000
[    0.000000] zynq_clock_init: clkc starts at df802100
[    0.000000] Zynq clock init
[    0.000014] sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 3298534883328ns
[    0.000303] ps7-ttc #0 at df804000, irq=43
[    0.000612] Console: colour dummy device 80x30
[    0.000644] Calibrating delay loop... 1332.01 BogoMIPS (lpj=6660096)
[    0.090249] pid_max: default: 32768 minimum: 301
[    0.090473] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.090492] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.092638] CPU: Testing write buffer coherency: ok
[    0.092976] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.093034] Setting up static identity map for 0x4c4af8 - 0x4c4b50
[    0.093255] L310 cache controller enabled
[    0.093275] l2x0: 8 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x72760000, Cache size: 512 kB
[    0.171032] CPU1: Booted secondary processor
[    0.260226] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.260355] Brought up 2 CPUs
[    0.260375] SMP: Total of 2 processors activated.
[    0.260382] CPU: All CPU(s) started in SVC mode.
[    0.261075] devtmpfs: initialized
[    0.263483] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[    0.264697] regulator-dummy: no parameters
[    0.271954] NET: Registered protocol family 16
[    0.274193] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.276469] cpuidle: using governor ladder
[    0.276482] cpuidle: using governor menu
[    0.283848] syscon f8000000.ps7-slcr: regmap [mem 0xf8000000-0xf8000fff] registered
[    0.285365] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[    0.285378] hw-breakpoint: maximum watchpoint size is 4 bytes.
[    0.285491] zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xdf880000
[    0.307203] bio: create slab <bio-0> at 0
[    0.308607] vgaarb: loaded
[    0.309308] SCSI subsystem initialized
[    0.310325] usbcore: registered new interface driver usbfs
[    0.310507] usbcore: registered new interface driver hub
[    0.310730] usbcore: registered new device driver usb
[    0.311276] media: Linux media interface: v0.10
[    0.311434] Linux video capture interface: v2.00
[    0.311672] pps_core: LinuxPPS API ver. 1 registered
[    0.311684] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.311812] PTP clock support registered
[    0.312181] EDAC MC: Ver: 3.0.0
[    0.313229] Advanced Linux Sound Architecture Driver Initialized.
[    0.316083] DMA-API: preallocated 4096 debug entries
[    0.316096] DMA-API: debugging enabled by kernel config
[    0.316170] Switched to clocksource arm_global_timer
[    0.335993] NET: Registered protocol family 2
[    0.336745] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[    0.336801] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[    0.336886] TCP: Hash tables configured (established 4096 bind 4096)
[    0.336936] TCP: reno registered
[    0.336953] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.336987] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.337233] NET: Registered protocol family 1
[    0.337570] RPC: Registered named UNIX socket transport module.
[    0.337582] RPC: Registered udp transport module.
[    0.337591] RPC: Registered tcp transport module.
[    0.337599] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.337612] PCI: CLS 0 bytes, default 64
[    0.338041] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[    0.340048] futex hash table entries: 512 (order: 3, 32768 bytes)
[    0.342158] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[    0.342351] msgmni has been set to 967
[    0.343124] io scheduler noop registered
[    0.343136] io scheduler deadline registered
[    0.343178] io scheduler cfq registered (default)
[    0.352630] dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-2364208
[    0.352650] dma-pl330 f8003000.ps7-dma: 	DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
[    0.475612] e0001000.serial: ttyPS0 at MMIO 0xe0001000 (irq = 82, base_baud = 3124999) is a xuartps
[    1.043583] console [ttyPS0] enabled
[    1.047863] xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to df866000
[    1.055464] [drm] Initialized drm 1.1.0 20060810
[    1.072439] brd: module loaded
[    1.081829] loop: module loaded
[    1.091230] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
[    1.097054] e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
[    1.104785] libphy: XEMACPS mii bus: probed
[    1.109328] ------------- phy_id = 0x3625e62
[    1.114060] xemacps e000b000.ps7-ethernet: pdev->id -1, baseaddr 0xe000b000, irq 54
[    1.122812] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.129473] ehci-pci: EHCI PCI platform driver
[    1.136701] zynq-dr e0002000.ps7-usb: Unable to init USB phy, missing?
[    1.143505] usbcore: registered new interface driver usb-storage
[    1.150360] mousedev: PS/2 mouse device common for all mice
[    1.156501] i2c /dev entries driver
[    1.163374] zynq-edac f8006000.ps7-ddrc: ecc not enabled
[    1.168902] cpufreq_cpu0: failed to get cpu0 regulator: -19
[    1.174800] Xilinx Zynq CpuIdle Driver started
[    1.179688] sdhci: Secure Digital Host Controller Interface driver
[    1.185786] sdhci: Copyright(c) Pierre Ossman
[    1.190149] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.197001] mmc0: no vqmmc regulator found
[    1.201014] mmc0: no vmmc regulator found
[    1.246229] mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
[    1.254918] usbcore: registered new interface driver usbhid
[    1.260430] usbhid: USB HID core driver
[    1.265134] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
[    1.271442] nand: Micron MT29F2G08ABAEAWP
[    1.275402] nand: 256MiB, SLC, page size: 2048, OOB size: 64
[    1.281338] Bad block table found at page 131008, version 0x01
[    1.287562] Bad block table found at page 130944, version 0x01
[    1.293614] 3 ofpart partitions found on MTD device pl353-nand
[    1.299407] Creating 3 MTD partitions on "pl353-nand":
[    1.304488] 0x000000000000-0x000002000000 : "BOOT.bin-env-dts-kernel"
[    1.312543] 0x000002000000-0x00000b000000 : "angstram-rootfs"
[    1.319859] 0x00000b000000-0x000010000000 : "upgrade-rootfs"
[    1.328798] TCP: cubic registered
[    1.332031] NET: Registered protocol family 17
[    1.336752] Registering SWP/SWPB emulation handler
[    1.342633] regulator-dummy: disabling
[    1.347023] UBI: attaching mtd1 to ubi0
[    1.873588] UBI: scanning is finished
[    1.885169] UBI: attached mtd1 (name "angstram-rootfs", size 144 MiB) to ubi0
[    1.892248] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    1.899008] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    1.905673] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
[    1.912550] UBI: good PEBs: 1152, bad PEBs: 0, corrupted PEBs: 0
[    1.918531] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
[    1.925639] UBI: max/mean erase counter: 2875/1371, WL threshold: 4096, image sequence number: 767909345
[    1.935115] UBI: available PEBs: 0, total reserved PEBs: 1152, PEBs reserved for bad PEB handling: 40
[    1.944330] UBI: background thread "ubi_bgt0d" started, PID 1080
[    1.944335] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[    1.948303] ALSA device list:
[    1.948306]   No soundcards found.
[    1.964694] UBIFS: background thread "ubifs_bgt0_0" started, PID 1082
[    1.993851] UBIFS: recovery needed
[    2.080207] UBIFS: recovery completed
[    2.083879] UBIFS: mounted UBI device 0, volume 0, name "rootfs"
[    2.089824] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[    2.098931] UBIFS: FS size: 128626688 bytes (122 MiB, 1013 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
[    2.108819] UBIFS: reserved for root: 0 bytes (0 KiB)
[    2.113849] UBIFS: media format: w4/r0 (latest is w4/r0), UUID F4300A22-CCD3-41F9-98C8-CD0E0F28FD62, small LPT model
[    2.125377] VFS: Mounted root (ubifs filesystem) on device 0:11.
[    2.132798] devtmpfs: mounted
[    2.135904] Freeing unused kernel memory: 204K (c06d2000 - c0705000)
[    2.977411] random: dd urandom read with 0 bits of entropy available
[    3.366206] 
[    3.366206] bcm54xx_config_init
[    3.976219] 
[    3.976219] bcm54xx_config_init
[    7.977035] xemacps e000b000.ps7-ethernet: Set clk to 124999998 Hz
[    7.983135] xemacps e000b000.ps7-ethernet: link up (1000/FULL)
[   22.685542] In axi fpga driver!
[   22.688647] request_mem_region OK!
[   22.692001] AXI fpga dev virtual address is 0xdf9fc000
[   22.697142] *base_vir_addr = 0x8c510
[   22.712024] In fpga mem driver!
[   22.715468] request_mem_region OK!
[   22.719085] fpga mem virtual address is 0xe2000000
[   23.485597] 
[   23.485597] bcm54xx_config_init
[   24.115517] 
[   24.115517] bcm54xx_config_init
[   28.115937] xemacps e000b000.ps7-ethernet: Set clk to 124999998 Hz
[   28.122040] xemacps e000b000.ps7-ethernet: link up (1000/FULL)
[  182.972298] random: nonblocking pool is initialized
Detect 512MB control board of XILINX
Miner Type = S9
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x0000ffff
Check chain[5] PIC fw version=0x03
Check chain[6] PIC fw version=0x03
Check chain[7] PIC fw version=0x03
Fix freq=600 Chain[5] voltage_pic=23 value=930
Fix freq=600 Chain[6] voltage_pic=23 value=930
Fix freq=600 Chain[7] voltage_pic=23 value=930
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
Chain[J6] has 63 asic
Chain[J7] has 63 asic
Chain[J8] has 63 asic
Chain[J6] has no freq in PIC, set default freq=600M
Chain[J6] has no core num in PIC
Chain[J7] has no freq in PIC, set default freq=600M
Chain[J7] has no core num in PIC
Chain[J8] has no freq in PIC, set default freq=600M
Chain[J8] has no core num in PIC

Miner fix freq ...
read PIC voltage=940 on chain[5]
Chain:5 chipnum=63
Asic[ 0]:600 
Asic[ 1]:600 Asic[ 2]:600 Asic[ 3]:600 Asic[ 4]:600 Asic[ 5]:600 Asic[ 6]:600 Asic[ 7]:600 Asic[ 8]:600 
Asic[ 9]:600 Asic[10]:600 Asic[11]:600 Asic[12]:600 Asic[13]:600 Asic[14]:600 Asic[15]:600 Asic[16]:600 
Asic[17]:600 Asic[18]:600 Asic[19]:600 Asic[20]:600 Asic[21]:600 Asic[22]:600 Asic[23]:600 Asic[24]:600 
Asic[25]:600 Asic[26]:600 Asic[27]:600 Asic[28]:600 Asic[29]:600 Asic[30]:600 Asic[31]:600 Asic[32]:600 
Asic[33]:600 Asic[34]:600 Asic[35]:600 Asic[36]:600 Asic[37]:600 Asic[38]:600 Asic[39]:600 Asic[40]:600 
Asic[41]:600 Asic[42]:600 Asic[43]:600 Asic[44]:600 Asic[45]:600 Asic[46]:600 Asic[47]:600 Asic[48]:600 
Asic[49]:600 Asic[50]:600 Asic[51]:600 Asic[52]:600 Asic[53]:600 Asic[54]:600 Asic[55]:600 Asic[56]:600 
Asic[57]:600 Asic[58]:600 Asic[59]:600 Asic[60]:600 Asic[61]:600 Asic[62]:600 
Chain:5 max freq=600
Chain:5 min freq=600

read PIC voltage=940 on chain[6]
Chain:6 chipnum=63
Asic[ 0]:600 
Asic[ 1]:600 Asic[ 2]:600 Asic[ 3]:600 Asic[ 4]:600 Asic[ 5]:600 Asic[ 6]:600 Asic[ 7]:600 Asic[ 8]:600 
Asic[ 9]:600 Asic[10]:600 Asic[11]:600 Asic[12]:600 Asic[13]:600 Asic[14]:600 Asic[15]:600 Asic[16]:600 
Asic[17]:600 Asic[18]:600 Asic[19]:600 Asic[20]:600 Asic[21]:600 Asic[22]:600 Asic[23]:600 Asic[24]:600 
Asic[25]:600 Asic[26]:600 Asic[27]:600 Asic[28]:600 Asic[29]:600 Asic[30]:600 Asic[31]:600 Asic[32]:600 
Asic[33]:600 Asic[34]:600 Asic[35]:600 Asic[36]:600 Asic[37]:600 Asic[38]:600 Asic[39]:600 Asic[40]:600 
Asic[41]:600 Asic[42]:600 Asic[43]:600 Asic[44]:600 Asic[45]:600 Asic[46]:600 Asic[47]:600 Asic[48]:600 
Asic[49]:600 Asic[50]:600 Asic[51]:600 Asic[52]:600 Asic[53]:600 Asic[54]:600 Asic[55]:600 Asic[56]:600 
Asic[57]:600 Asic[58]:600 Asic[59]:600 Asic[60]:600 Asic[61]:600 Asic[62]:600 
Chain:6 max freq=600
Chain:6 min freq=600

read PIC voltage=940 on chain[7]
Chain:7 chipnum=63
Asic[ 0]:600 
Asic[ 1]:600 Asic[ 2]:600 Asic[ 3]:600 Asic[ 4]:600 Asic[ 5]:600 Asic[ 6]:600 Asic[ 7]:600 Asic[ 8]:600 
Asic[ 9]:600 Asic[10]:600 Asic[11]:600 Asic[12]:600 Asic[13]:600 Asic[14]:600 Asic[15]:600 Asic[16]:600 
Asic[17]:600 Asic[18]:600 Asic[19]:600 Asic[20]:600 Asic[21]:600 Asic[22]:600 Asic[23]:600 Asic[24]:600 
Asic[25]:600 Asic[26]:600 Asic[27]:600 Asic[28]:600 Asic[29]:600 Asic[30]:600 Asic[31]:600 Asic[32]:600 
Asic[33]:600 Asic[34]:600 Asic[35]:600 Asic[36]:600 Asic[37]:600 Asic[38]:600 Asic[39]:600 Asic[40]:600 
Asic[41]:600 Asic[42]:600 Asic[43]:600 Asic[44]:600 Asic[45]:600 Asic[46]:600 Asic[47]:600 Asic[48]:600 
Asic[49]:600 Asic[50]:600 Asic[51]:600 Asic[52]:600 Asic[53]:600 Asic[54]:600 Asic[55]:600 Asic[56]:600 
Asic[57]:600 Asic[58]:600 Asic[59]:600 Asic[60]:600 Asic[61]:600 Asic[62]:600 
Chain:7 max freq=600
Chain:7 min freq=600

max freq = 600
set baud=1
Chain[J6] PIC temp offset=62,0,0,0,0,0,35,28
Chain[J6] chip[244] use PIC middle temp offset=0 typeID=55
New offset Chain[5] chip[244] local:49 remote:55 offset:26 
Chain[J6] chip[244] get middle temp offset=26 typeID=55
Chain[J6] chip[136] use PIC middle temp offset=28 typeID=00
Warning: Chain[J6] has no temp offset in PIC! will fix it
New offset Chain[5] chip[244] local:48 remote:54 offset:26 
Chain[J6] chip[244] get middle temp offset=26 typeID=55
Chain[J7] PIC temp offset=62,0,0,0,0,0,35,28
Chain[J7] chip[244] use PIC middle temp offset=0 typeID=55
New offset Chain[6] chip[244] local:42 remote:46 offset:27 
Chain[J7] chip[244] get middle temp offset=27 typeID=55
Chain[J7] chip[136] use PIC middle temp offset=28 typeID=00
Warning: Chain[J7] has no temp offset in PIC! will fix it
New offset Chain[6] chip[244] local:41 remote:45 offset:27 
Chain[J7] chip[244] get middle temp offset=27 typeID=55
Chain[J8] PIC temp offset=62,0,0,0,0,0,35,28
Chain[J8] chip[244] use PIC middle temp offset=0 typeID=55
New offset Chain[7] chip[244] local:35 remote:40 offset:26 
Chain[J8] chip[244] get middle temp offset=26 typeID=55
Chain[J8] chip[136] use PIC middle temp offset=28 typeID=00
Warning: Chain[J8] has no temp offset in PIC! will fix it
New offset Chain[7] chip[244] local:35 remote:40 offset:26 
Chain[J8] chip[244] get middle temp offset=26 typeID=55
Chain[J6] set working voltage=930 [23]
Chain[J7] set working voltage=930 [23]
Chain[J8] set working voltage=930 [23]
setStartTimePoint total_tv_start_sys=72 total_tv_end_sys=73
restartNum = 2 , auto-reinit enabled...
do read_temp_func once...
do check_asic_reg 0x08

get RT hashrate from Chain[5]: (asic index start from 1-63)
Asic[01]=70.5810 Asic[02]=70.2790 Asic[03]=65.0110 Asic[04]=70.2790 Asic[05]=69.7090 Asic[06]=69.9940 Asic[07]=71.3870 Asic[08]=69.3900 
Asic[09]=70.1450 Asic[10]=70.3460 Asic[11]=68.8360 Asic[12]=67.2760 Asic[13]=63.6860 Asic[14]=73.0470 Asic[15]=65.7160 Asic[16]=69.1380 
Asic[17]=68.8200 Asic[18]=70.9340 Asic[19]=68.1820 Asic[20]=65.0620 Asic[21]=66.2020 Asic[22]=70.2290 Asic[23]=67.4610 Asic[24]=67.8800 
Asic[25]=67.3600 Asic[26]=65.9340 Asic[27]=71.9570 Asic[28]=66.2190 Asic[29]=62.1260 Asic[30]=69.8260 Asic[31]=64.8270 Asic[32]=67.4940 
Asic[33]=65.4470 Asic[34]=73.0140 Asic[35]=61.2530 Asic[36]=67.1590 Asic[37]=71.6550 Asic[38]=68.4170 Asic[39]=64.6760 Asic[40]=59.9280 
Asic[41]=67.7960 Asic[42]=70.6650 Asic[43]=74.9270 Asic[44]=62.0080 Asic[45]=67.3430 Asic[46]=63.5180 Asic[47]=70.4810 Asic[48]=60.4980 
Asic[49]=68.2490 Asic[50]=71.5880 Asic[51]=68.6520 Asic[52]=67.5950 Asic[53]=70.1280 Asic[54]=61.7560 Asic[55]=63.9040 Asic[56]=65.9000 
Asic[57]=66.8570 Asic[58]=66.0180 Asic[59]=69.6420 Asic[60]=65.5310 Asic[61]=69.5750 Asic[62]=65.0450 Asic[63]=66.8230 

get RT hashrate from Chain[6]: (asic index start from 1-63)
Asic[01]=70.2790 Asic[02]=70.2790 Asic[03]=70.7660 Asic[04]=69.6920 Asic[05]=64.0550 Asic[06]=66.2530 Asic[07]=63.9370 Asic[08]=68.3160 
Asic[09]=61.1020 Asic[10]=65.5820 Asic[11]=66.2020 Asic[12]=64.6420 Asic[13]=67.9980 Asic[14]=67.3100 Asic[15]=60.7830 Asic[16]=68.5510 
Asic[17]=64.3740 Asic[18]=66.4200 Asic[19]=65.5820 Asic[20]=66.8730 Asic[21]=69.5080 Asic[22]=65.5650 Asic[23]=63.6860 Asic[24]=68.8870 
Asic[25]=67.6620 Asic[26]=70.9500 Asic[27]=67.7120 Asic[28]=67.6280 Asic[29]=67.8300 Asic[30]=71.3530 Asic[31]=69.2730 Asic[32]=70.2620 
Asic[33]=64.0720 Asic[34]=70.9670 Asic[35]=70.5480 Asic[36]=69.8090 Asic[37]=72.2760 Asic[38]=72.0740 Asic[39]=61.3200 Asic[40]=68.9040 
Asic[41]=68.7360 Asic[42]=71.2690 Asic[43]=63.8030 Asic[44]=63.4010 Asic[45]=70.2790 Asic[46]=69.2560 Asic[47]=67.1420 Asic[48]=66.5710 
Asic[49]=60.1960 Asic[50]=69.9270 Asic[51]=75.6480 Asic[52]=67.6790 Asic[53]=62.5790 Asic[54]=62.9480 Asic[55]=63.3170 Asic[56]=65.3640 
Asic[57]=66.6390 Asic[58]=62.3440 Asic[59]=73.5170 Asic[60]=66.6220 Asic[61]=64.6250 Asic[62]=63.9370 Asic[63]=66.1690 

get RT hashrate from Chain[7]: (asic index start from 1-63)
Asic[01]=70.0950 Asic[02]=74.9270 Asic[03]=69.8930 Asic[04]=72.5780 Asic[05]=65.4810 Asic[06]=75.4800 Asic[07]=60.6990 Asic[08]=69.9600 
Asic[09]=65.3800 Asic[10]=69.4740 Asic[11]=63.1490 Asic[12]=72.4770 Asic[13]=67.6620 Asic[14]=67.9140 Asic[15]=72.4770 Asic[16]=70.5640 
Asic[17]=68.0810 Asic[18]=69.0880 Asic[19]=67.0240 Asic[20]=67.0920 Asic[21]=73.2660 Asic[22]=73.2660 Asic[23]=69.4910 Asic[24]=67.0240 
Asic[25]=70.0950 Asic[26]=70.0440 Asic[27]=66.7390 Asic[28]=65.8840 Asic[29]=70.8330 Asic[30]=67.9470 Asic[31]=69.5580 Asic[32]=60.9680 
Asic[33]=74.0370 Asic[34]=67.5950 Asic[35]=73.3830 Asic[36]=71.5540 Asic[37]=66.6890 Asic[38]=69.5080 Asic[39]=68.1150 Asic[40]=63.2330 
Asic[41]=62.8810 Asic[42]=67.3260 Asic[43]=70.8330 Asic[44]=67.4770 Asic[45]=72.4940 Asic[46]=66.0510 Asic[47]=65.8670 Asic[48]=65.5150 
Asic[49]=64.0880 Asic[50]=68.1820 Asic[51]=69.8090 Asic[52]=68.6850 Asic[53]=67.5610 Asic[54]=64.3400 Asic[55]=70.0110 Asic[56]=69.1550 
Asic[57]=72.3760 Asic[58]=64.6250 Asic[59]=64.5750 Asic[60]=70.2120 Asic[61]=67.3940 Asic[62]=70.7990 Asic[63]=68.3670 
Check Chain[J6] ASIC RT error: (asic index start from 1-63)
Check Chain[J7] ASIC RT error: (asic index start from 1-63)
Check Chain[J8] ASIC RT error: (asic index start from 1-63)
Done check_asic_reg
do read temp on Chain[5]
Chain[5] Chip[62] TempTypeID=55 middle offset=26
Chain[5] Chip[62] local Temp=76
Chain[5] Chip[62] middle Temp=63
Done read temp on Chain[5]
do read temp on Chain[6]
Chain[6] Chip[62] TempTypeID=55 middle offset=27
Chain[6] Chip[62] local Temp=68
Chain[6] Chip[62] middle Temp=58
Done read temp on Chain[6]
do read temp on Chain[7]
Chain[7] Chip[62] TempTypeID=55 middle offset=26
Chain[7] Chip[62] local Temp=83
Chain[7] Chip[62] middle Temp=71
Done read temp on Chain[7]
set FAN speed according to: temp_highest=71 temp_top1[PWM_T]=71 temp_top1[TEMP_POS_LOCAL]=83 temp_change=11 fix_fan_steps=0
set full FAN speed...
FAN PWM: 100
read_temp_func Done!
CRC error counter=0

[BitMaxz]

I can not find any error or failure in the kernel log and I can not find the BMminer and Hardware version.

Can you add more details and screenshot of the miner status and overview here.

Overview sample:

Code:

Miner Type: Antminer S9-14.0T
Hardware Version: 16.8.1.2
Kernel Version: Linux 3.15.0-xilinx-ge8a2f71-dirty #82 SMP PREEMPT Tue May 16 19:49:53 CST 2017
File System Version: Mon Nov 6 17:17:48 CST 2017
Logic Version: S9_V1.47
BMminer Version: 2.0.0
Controller Board Version: 1.20

It looks fine but have you tried the other firmware? How about the latest one (Antminer-S9-all-201705031918-550M-user-Update2UBI-NF.tar.gz)?

[Dragonizer]

I can not find any error or failure in the kernel log and I can not find the BMminer and Hardware version.

Can you add more details and screenshot of the miner status and overview here.

Overview sample:

Code:

Miner Type: Antminer S9-14.0T
Hardware Version: 16.8.1.2
Kernel Version: Linux 3.15.0-xilinx-ge8a2f71-dirty #82 SMP PREEMPT Tue May 16 19:49:53 CST 2017
File System Version: Mon Nov 6 17:17:48 CST 2017
Logic Version: S9_V1.47
BMminer Version: 2.0.0
Controller Board Version: 1.20

It looks fine but have you tried the other firmware? How about the latest one (Antminer-S9-all-201705031918-550M-user-Update2UBI-NF.tar.gz)?

Tried them all....Still no joy, i put the third card in another S9 and and it works fine ?? All the fixed FW's allow to to alter the freq anyway..lol eg 500, 600 or 650...

[tim-bc]

Try running one hashboard at a time and see if the issue still occurs with each one. Could also be a power issue, have you tried another psu?