Hello,
My S19J Pro 104th stopped hash yesterday.
Rate abnormal
Temp abnormal
Fault light is on.
Im new to mining and would be nice with some support.
Pool: Nicehash
My log here:
2023-12-24 18:18:31 fails to write 1
2023-12-24 18:18:31 fails to read 0:1
2023-12-24 18:18:31 fails to write 1
2023-12-24 18:18:31 fails to read 0:1
2023-12-24 18:18:31 fails to write 1
2023-12-24 18:18:31 fails to read 0:1
2023-12-24 18:18:31 fails to write 1
2023-12-24 18:18:31 fails to read 0:1
2023-12-24 18:18:31 fails to write 1
2023-12-24 18:18:31 fails to read 0:1
2023-12-24 18:18:31 load chain 1 eeprom data
2023-12-24 18:18:34 load chain 2 eeprom data
2023-12-24 18:18:34 i2c_sim_init start
2023-12-24 18:18:34 init gpio477
2023-12-24 18:18:34 init gpio476
2023-12-24 18:18:34 i2c_sim_init end
2023-12-24 18:18:36 power open power_version = 0x75
2023-12-24 18:18:38 power is not calibrated
2023-12-24 18:18:40 miner type: Antminer S19j Pro
2023-12-24 18:18:40 multimachine mode
2023-12-24 18:18:40 load machine BHB42631 conf
2023-12-24 18:18:40 machine: BHB42631
2023-12-24 18:18:40 chain_num 4, chain_domain_num 42, chain_asic_num 126, domain_asic_num 3
2023-12-24 18:18:40 abandon mixboard!
2023-12-24 18:18:40 abandon mixboard!
2023-12-24 18:18:40 fan_eft: 1 fan_pwm: 80
2023-12-24 18:18:40 create thread get_nonce_and_register_thread
2023-12-24 18:18:40 fixed working voltage = 1360
2023-12-24 18:18:40 fixed frequency is 525
2023-12-24 18:18:40 Chain
2023-12-24 18:18:40 Chain
2023-12-24 18:18:40 Chain [1] PCB Version: 0x0130
2023-12-24 18:18:40 Chain [1] BOM Version: 0x0010
2023-12-24 18:18:40 Chain [2] PCB Version: 0x0130
2023-12-24 18:18:40 Chain [2] BOM Version: 0x0010
2023-12-24 18:18:40 bad chain ID = 3
2023-12-24 18:18:40 Fan control approved.
2023-12-24 18:18:40 uart_trans addr:0xf70a6000.
2023-12-24 18:18:40 max sensor number = 4
2023-12-24 18:18:40 STATUS_INITED: soc init complete!
2023-12-24 18:18:40 temperature_monitor_thread_start...
2023-12-24 18:18:40 cannot read tsensor via iic, chain: 1, slave: 72, addr: 0
2023-12-24 18:18:40 cannot read image temp for chain 1
2023-12-24 18:18:40 cannot read tsensor via iic, chain: 1, slave: 76, addr: 0
2023-12-24 18:18:40 cannot read image temp for chain 1
2023-12-24 18:18:41 cannot read tsensor via iic, chain: 1, slave: 72, addr: 0
2023-12-24 18:18:41 unable to read image temp for chain 1
2023-12-24 18:18:41 cannot read tsensor via iic, chain: 1, slave: 76, addr: 0
2023-12-24 18:18:41 unable to read image temp for chain 1
2023-12-24 18:18:42 cannot read tsensor via iic, chain: 1, slave: 72, addr: 0
2023-12-24 18:18:42 cannot read image temp for chain 1
2023-12-24 18:18:42 cannot read tsensor via iic, chain: 1, slave: 76, addr: 0
2023-12-24 18:18:42 cannot read image temp for chain 1
2023-12-24 18:18:42 over max temp, pcb temp 26 (max 75), chip temp 26 (max 95) pcb temp rise 0 chip temp rise 0, total_exit_failure 6
2023-12-24 18:18:42 Sweep error string = J0:6.
2023-12-24 18:18:42 ERROR_TEMP_TOO_HIGH: over max temp
2023-12-24 18:18:42 stop_mining: over max temp
2023-12-24 18:18:42 uninit_temp_info
2023-12-24 18:18:42 no longer reading temp...
2023-12-24 18:18:42 cancel thread
2023-12-24 18:18:42 *power off hashboard*
2023-12-24 18:18:42 starting...
2023-12-24 18:18:42 warning: power is not calibrated.
2023-12-24 18:18:42 Version number 65536
2023-12-24 18:18:42 Mask num 0x1fffe000
2023-12-24 18:18:42 opt_multi_version = 65536, interval timeout = 2945120
2023-12-24 18:18:42 freq = 525, percent = 90, hcn = 4993, timeout = 2945120
2023-12-24 18:18:44 power type version: 0x0075
2023-12-24 18:18:45 disable power watchdog: 0x0000
2023-12-24 18:18:46 temp monitor thread exit
2023-12-24 18:18:46 Initializing power, wait, this may take up to 2 minutes...
