What is the maximum overclocking limit for a mining machine? Is it safe?

[uefbv]

Is it safe?

[philipma1957]

question is too general.

best answer is cooling cooling cooling allows higher over clocks.


but overclocks are a degenerate move which often kills a machine.



i have been mining since 2012. I have consistently found underclocks dont break the gear and that over clocks break the gear.

[FP91G]

Is it safe?

This needs to be discussed for each ASIC model.
Sometimes overclocking is not beneficial due to higher power consumption and overheating. If you are interested in non-factory firmware, then this is also a separate topic for dialogue.
If you have installed water cooling, then overclocking is possible, but this is usually done for heating a house, greenhouse or pool.

[uefbv]

question is too general.

best answer is cooling cooling cooling allows higher over clocks.


but overclocks are a degenerate move which often kills a machine.



i have been mining since 2012. I have consistently found underclocks dont break the gear and that over clocks break the gear.

Just like singing, if you toil day and night, your voice might sound beautiful and you might earn a lot of money, but it will damage your body. Over time, your body will be unable to bear it and will eventually collapse! Right?

[philipma1957]

question is too general.

best answer is cooling cooling cooling allows higher over clocks.


but overclocks are a degenerate move which often kills a machine.



i have been mining since 2012. I have consistently found underclocks dont break the gear and that over clocks break the gear.

Just like singing, if you toil day and night, your voice might sound beautiful and you might earn a lot of money, but it will damage your body. Over time, your body will be unable to bear it and will eventually collapse! Right?

Well some singers nurse their voices and can sing well into their 80’s

[uefbv]

question is too general.

best answer is cooling cooling cooling allows higher over clocks.


but overclocks are a degenerate move which often kills a machine.



i have been mining since 2012. I have consistently found underclocks dont break the gear and that over clocks break the gear.

Just like singing, if you toil day and night, your voice might sound beautiful and you might earn a lot of money, but it will damage your body. Over time, your body will be unable to bear it and will eventually collapse! Right?

Well some singers nurse their voices and can sing well into their 80’s

It still depends on how to maintain it?  😁😁😁

Is it safe?

This needs to be discussed for each ASIC model.
Sometimes overclocking is not beneficial due to higher power consumption and overheating. If you are interested in non-factory firmware, then this is also a separate topic for dialogue.
If you have installed water cooling, then overclocking is possible, but this is usually done for heating a house, greenhouse or pool.

Does this mean that water cooling is installed, and overclocking will not harm the mining machine itself?

[Kryss191]

Honestly, there isn’t really a “max” that fits every card. It depends a lot on the GPU model, cooling, and your power setup. Most miners just push clocks slowly until it starts crashing or temps get too high, then back it off a bit. As long as you keep temps under control and don’t go crazy with voltage, it’s usually safe. The real danger is heat and running fans 24/7, that’s what kills parts over time.

[philipma1957]

Honestly, there isn’t really a “max” that fits every card. It depends a lot on the GPU model, cooling, and your power setup. Most miners just push clocks slowly until it starts crashing or temps get too high, then back it off a bit. As long as you keep temps under control and don’t go crazy with voltage, it’s usually safe. The real danger is heat and running fans 24/7, that’s what kills parts over time.

Ahh that depends..
A high energy asic.

The s21xp burns about 3500 watts it is energy dense  in terms of its actual size.

Even with great cooling it can over heat really fast if cooling has an issue.

The 4 fans pull air hard and they are 140mm 6000 rpm plus fans.

If they suck a plastic wrapper or a piece of paper to the rear fan the air flow drops 30 to 60 percent in an instant.

But all the meters for the until read fans are working and the until will slowly heat up.

Then the unit may not shut down fast enough to cool off and you toasted the gear.

Been there done that.

If you were clocked with after market at 90% and set shut down at 78c . The gear will likely not die.

If you are clocked at 100% and 85c or stock maybe it gets damaged maybe not.

But if you clock to 110% and set temp to 88c. Huge chance you toast the gear.



This is also true of really high power gpus 3090s 3090tis etc.


But lite duty gear say antminer L3+ an 800 watt miner it is way harder to burn it out from over clock.  Or the 3060ti gpu

[FP91G]

Is it safe?

This needs to be discussed for each ASIC model.
Sometimes overclocking is not beneficial due to higher power consumption and overheating. If you are interested in non-factory firmware, then this is also a separate topic for dialogue.
If you have installed water cooling, then overclocking is possible, but this is usually done for heating a house, greenhouse or pool.

Does this mean that water cooling is installed, and overclocking will not harm the mining machine itself?

The same ASICs with water cooling can be overclocked more, because water cooling is more effective, it is:
1. much more expensive
2. more difficult to maintain
3. not always possible to use

It is actively developing now, but the simplest and most proven method is air cooling.

[AlexPalma]

It must be evaluated model by model, but he first limitations are:
1-Temperature (solution: liquid cooling)
2-PSU limitation (solution: replace the stock PSU with a more powerful one)

Then you realize that it was a fun experiment, but that the ASIC became much less efficient in terms of power draw/hashrate, so you put everything back the way it was because what really matters is the sweet spot of efficiency.

Generally, this sweet spot is achieved with better-developed firmware, without hardware changes.

[Outhue]

If this is your first time I suggest you grab yourself an old asic miner, like the old S9 Antminer to do some testing, the best answer is how cool they can get along the way.

Gradual increase of small percentage and seeing how the cooling gets is the key, I suggest you watch YouTube videos online for a specific Asic miner because they are built differently too.

Few miners can handle OC out of the box and still be able to cool without upgrading the power supply or adding extra coolings, but the OC percentage vs the factory clock won't be that different.

[philipma1957]

If this is your first time I suggest you grab yourself an old asic miner, like the old S9 Antminer to do some testing, the best answer is how cool they can get along the way.

Gradual increase of small percentage and seeing how the cooling gets is the key, I suggest you watch YouTube videos online for a specific Asic miner because they are built differently too.

Few miners can handle OC out of the box and still be able to cool without upgrading the power supply or adding extra coolings, but the OC percentage vs the factory clock won't be that different.

If you want a number or percentage 5% overclock with proper psu and proper cooling should work and be safe.


while 25% even with a proper psu and proper cooling will likely knock the machine out quicker.

That is for air cooling.

liquid cooling you can likely do 35% on some gear but zero slip ups or the gear will die.

People do not understand that overclock is almost never is worth it.
yeah if there is a high paying in fees which does happen.

You can over clock while it lasts. other than that it is not cost effective.