@perogi
Why dont you try like jorgebanilla few post back, he got the same error. Read his post on page 155
Thanks alfabitcoin - Note that I was following jorgebanilla during this thread (see below) but the problem is that it seems that my miner's image was "upgraded" when I received it. Without having access to the original image, it would be impossible to follow his instructions "I reverted back to to original image (not the one from dropbox but the one that came with it, which i have no root access to)"
<<<Lots of good stuff>>
[2014-08-23 03:37:38] No any A1 board
NO ANY A1 BOARD???, i don't know what to do next. if anyone has figure this one out, please share your wisdom.
I'll keep trying but i'm currently stuck here, will try to help my brother to see if we have any luck there.
I'll keep you updated if i'm in fact able to figure out. HELP is appreciated!
Same issue here bud. :-/
I got it to work!!!
I reverted back to to original image (not the one from dropbox but the one that came with it, which i have no root access to)
And i changed ip,subnet,gw and dns to be opendns 208.67.222.222. Setup pool, and it works!!!
Hashing ####
Stats coming up....
What error are you getting?
AMT_Miners
Here's my information:
ip: 192.168.0.124
netmask: 255.255.255.0
gateway: 192.168.0.1 (this matches my network - i am able to ping us1.ghash.io)
DNS: tried both 8.8.8.8 and 208.67.222.222 per jorgebonilla
pool_0: stratum+tcp://us1.ghash.io:3333
account: <account_name>.amt1
password: 123
Since it appears that it starts in silent mode, I used this command from /var/www
sudo ./cgminer -o stratum+tcp://uk1.ghash.io:3333 -u perogi.amt -p 5254152 --A1Pll1 950 --A1Pll2 950 --A1Pll3 950 --A1Pll4 950 --A1Pl l5 950 --diff 15 --api-listen --cs 8 --stmcu 0 --hwreset --api-allow W:127.0.0.1 --verbose
Output:
[2014-08-25 07:25:14] Started cgminer 3.9.3
[2014-08-25 07:25:14] Run Reset=1
[2014-08-25 07:25:14] ST MCU hardware reset start
[2014-08-25 07:25:22] SPI Speed 4000 kHz
[2014-08-25 07:25:22] ST MCU - Enable (Pre-header)
[2014-08-25 07:25:22] A1 = 950,1
[2014-08-25 07:25:22] A1 PLL Clock = 950MHz
[2014-08-25 07:25:22] A1 = 950,1
[2014-08-25 07:25:22] A1 PLL Clock = 950MHz
[2014-08-25 07:25:22] A1 = 950,1
[2014-08-25 07:25:22] A1 PLL Clock = 950MHz
[2014-08-25 07:25:22] A1 = 950,1
[2014-08-25 07:25:22] A1 PLL Clock = 950MHz
[2014-08-25 07:25:22] A1 = 950,1
[2014-08-25 07:25:22] A1 PLL Clock = 950MHz
[2014-08-25 07:25:22] ASIC Difficulty = 256
[2014-08-25 07:25:22] AUTO GPIO CS
[2014-08-25 07:25:22] SPI '/dev/spidev0.0': mode=1, bits=8, speed=4000000
[2014-08-25 07:25:28] Failure(cs0)(20): missing ACK for cmd 0x04
[2014-08-25 07:25:28] ACK(cs0) timeout:cmd_RESET_BCAST-6.3550s
[2014-08-25 07:25:28] SPI '/dev/spidev0.0': mode=1, bits=8, speed=4000000
[2014-08-25 07:25:34] Failure(cs1)(20): missing ACK for cmd 0x04
[2014-08-25 07:25:34] ACK(cs1) timeout:cmd_RESET_BCAST-6.3528s
[2014-08-25 07:25:34] SPI '/dev/spidev0.0': mode=1, bits=8, speed=4000000
[2014-08-25 07:25:40] Failure(cs2)(20): missing ACK for cmd 0x04
[2014-08-25 07:25:40] ACK(cs2) timeout:cmd_RESET_BCAST-6.3738s
[2014-08-25 07:25:40] SPI '/dev/spidev0.0': mode=1, bits=8, speed=4000000
[2014-08-25 07:25:46] Failure(cs3)(20): missing ACK for cmd 0x04
[2014-08-25 07:25:46] ACK(cs3) timeout:cmd_RESET_BCAST-6.3050s
[2014-08-25 07:25:46] SPI '/dev/spidev0.0': mode=1, bits=8, speed=4000000
[2014-08-25 07:25:52] Failure(cs4)(20): missing ACK for cmd 0x04
[2014-08-25 07:25:52] ACK(cs4) timeout:cmd_RESET_BCAST-6.3107s
[2014-08-25 07:25:52] SPI '/dev/spidev0.0': mode=1, bits=8, speed=4000000
[2014-08-25 07:25:58] Failure(cs5)(20): missing ACK for cmd 0x04
[2014-08-25 07:25:58] ACK(cs5) timeout:cmd_RESET_BCAST-6.3273s
[2014-08-25 07:25:58] No any A1 board
No any A1 board
: No such file or directory
Thanks,
perogi.
EDIT: I also tried using
ip: 192.168.1.100
netmask: 255.255.255.0
gateway: 192.168.1.1 (added a router and used that to allow communication between 192.168.1.1 and 192.168.0.1)
DNS: tried both 8.8.8.8 and 208.67.222.222