Looking for ANTMINER S7 6" to 4" Adapter fan duct heating cooling

[cabal2000]

Looking for this
http://www.ebay.ca/itm/ANTMINER-S7-6-to-4-Adapter-fan-duct-heating-cooling/162015404197
Not going to the very hefty price but its a great idea.
Anyone know where I can get my hands on 6 or 12 of these?

[1714801283]

1714801283

[1714801283]

1714801283

[1714801283]

1714801283

[1714801283]

1714801283

[1714801283]

1714801283

[philipma1957]

Looking for this
http://www.ebay.ca/itm/ANTMINER-S7-6-to-4-Adapter-fan-duct-heating-cooling/162015404197
Not going to the very hefty price but its a great idea.
Anyone know where I can get my hands on 6 or 12 of these?

Watch for overheating.

The reduction in size restricts air speed.

Look into flex vent from Home Depot use bigger like 12 inch put the whole miner in it.

Just about 1 foot inside on intake

 put a small  hole in the vent to allow your pcie cables .

Then make the exhaust side as long as you want .

Just go to Home Depot and search for flex duct 12 inches or 10 inches.

[dogie]

Just go to Home Depot and search for flex duct 12 inches or 10 inches.

He wants something that screws into the fan/mount.

You could probably repurpose one of these, in the worst case cutting them in half to get 2x and then using tape to join the duct to duct ends.
http://www.frozencpu.com/products/16138/duc-55/Akust_Extendable_Air_Flow_Thermal_Hood_-_70_80_92_120_Fans_-_Black_FG02-0100-AKS.html?tl=g54c505s1965
http://www.frozencpu.com/products/18219/duc-61/Akust_Extendable_Air_Flow_Thermal_Hood_-_120_140_Fans_-_Black_FG02-0102-AKS.html?tl=g54c505s1965

[philipma1957]

Just go to Home Depot and search for flex duct 12 inches or 10 inches.

He wants something that screws into the fan/mount.

You could probably repurpose one of these, in the worst case cutting them in half to get 2x and then using tape to join the duct to duct ends.
http://www.frozencpu.com/products/16138/duc-55/Akust_Extendable_Air_Flow_Thermal_Hood_-_70_80_92_120_Fans_-_Black_FG02-0100-AKS.html?tl=g54c505s1965
http://www.frozencpu.com/products/18219/duc-61/Akust_Extendable_Air_Flow_Thermal_Hood_-_120_140_Fans_-_Black_FG02-0102-AKS.html?tl=g54c505s1965

I had some made up on a 3d printer.   They raised temps 3 to 6 c.

So I do not like them.

[smaxz]

yeah but you could always drop some ducting down from a ventilation fan that is pulling upwards of 150cfm and split to multiple miners to draw away the heat.. ambient would benefit and the result would be a push/pull for the S7F1 at minimal cost.

thanks for the link

[xxcsu]

Im using this one from ebay on two S7 :
http://www.ebay.com/itm/201527240893

Did not noticed any temp change , ambient temp is around  20-22C , fan speed set to 55% , miner temp 58/55/58 another one from different bach is 64/58/63

[philipma1957]

Im using this one from ebay on two S7 :
http://www.ebay.com/itm/201527240893

Did not noticed any temp change , ambient temp is around  20-22C , fan speed set to 55% , miner temp 58/55/58 another one from different bach is 64/58/63

your ambient is a lot lower  ( I am 27-31)   which may be why you are good.

My miners are 62/61/63 with fans at 3000 rpm