lbr (OP)
|
|
January 03, 2017, 12:04:44 PM |
|
6 x RX470, 16.10.2 driver, win7 x64 works with mod, but with newer drivers only 5 cards (sixth with 43 error code).
Where did you get 16.10.2 driver, from AMD site?
|
|
|
|
|
|
|
"I'm sure that in 20 years there will either be very large transaction volume or no volume." -- Satoshi
|
|
|
Advertised sites are not endorsed by the Bitcoin Forum. They may be unsafe, untrustworthy, or illegal in your jurisdiction.
|
|
|
|
lbr (OP)
|
|
January 03, 2017, 02:29:27 PM |
|
I've compared inf from this driver to 16.10.1(which I could not make to work with 6x470) They differ in those three settings under Polaris10(RX 480, RX 470) config [ati2mtag_Polaris10_SoftwareDeviceSettings] HKR,,BDEFF89820EFD7EFFD30, %REG_BINARY%,62,30,06,E1 HKR,,BDEFF99820EFD7EFFD30, %REG_BINARY%,62,30,06,E1 HKR,,BDEFFA9820EFD7EFFD38, %REG_BINARY%,62,36,06,E2
Wtf is this, I've no idea ; ) Next step would be - add those to latest driver, including all changes done by 6xGPU mod and see what happens on 6x470/480 rig.
|
|
|
|
IojkinKot
Newbie
Offline
Activity: 63
Merit: 0
|
|
January 03, 2017, 07:21:42 PM |
|
Hi lbr! My hardware: 6x RX470 8G Gigabyte z170 gaming k3 8G RAM G4400 CPU
AMD drivers 16.11.5
In windows 7 x64 two GPUs have code 43 error. After i use your program and patch registry only 5 GPUs work fine and one - code 43 error. In Windows 10 work all 6 GPUs, but win10 unstabe, and telemetry, and updates... Can you wrote new program, which can run all 6 GPUs on Win7? I'll donate you, if you can.
This program works very well with 6 gpu, win 7 64bit, Crimson 16.10.2 Driver. With 6 x RX480's? I tried that, no go. 6 x RX470, 16.10.2 driver, win7 x64 works with mod, but with newer drivers only 5 cards (sixth with 43 error code). NO! 16.10.2 driver don't work! I tried clean install Win 7x64 with AMD 16.10.2 driver and install mod - only 5 GPU work!
|
|
|
|
avirdoz
Legendary
Offline
Activity: 1191
Merit: 1001
|
|
January 03, 2017, 08:34:39 PM |
|
Hi lbr! My hardware: 6x RX470 8G Gigabyte z170 gaming k3 8G RAM G4400 CPU
AMD drivers 16.11.5
In windows 7 x64 two GPUs have code 43 error. After i use your program and patch registry only 5 GPUs work fine and one - code 43 error. In Windows 10 work all 6 GPUs, but win10 unstabe, and telemetry, and updates... Can you wrote new program, which can run all 6 GPUs on Win7? I'll donate you, if you can.
This program works very well with 6 gpu, win 7 64bit, Crimson 16.10.2 Driver. With 6 x RX480's? I tried that, no go. 6 x RX470, 16.10.2 driver, win7 x64 works with mod, but with newer drivers only 5 cards (sixth with 43 error code). NO! 16.10.2 driver don't work! I tried clean install Win 7x64 with AMD 16.10.2 driver and install mod - only 5 GPU work! https://i.imgur.com/KML9UEI.png
|
|
|
|
Hadmart
Newbie
Offline
Activity: 56
Merit: 0
|
|
January 05, 2017, 01:16:37 PM |
|
Hi lbr! My hardware: 6x RX470 8G Gigabyte z170 gaming k3 8G RAM G4400 CPU
AMD drivers 16.11.5
In windows 7 x64 two GPUs have code 43 error. After i use your program and patch registry only 5 GPUs work fine and one - code 43 error. In Windows 10 work all 6 GPUs, but win10 unstabe, and telemetry, and updates... Can you wrote new program, which can run all 6 GPUs on Win7? I'll donate you, if you can.
This program works very well with 6 gpu, win 7 64bit, Crimson 16.10.2 Driver. With 6 x RX480's? I tried that, no go. 6 x RX470, 16.10.2 driver, win7 x64 works with mod, but with newer drivers only 5 cards (sixth with 43 error code). NO! 16.10.2 driver don't work! I tried clean install Win 7x64 with AMD 16.10.2 driver and install mod - only 5 GPU work! https://i.imgur.com/KML9UEI.pngYou need to run the mod with administrator rights.
|
|
|
|
h311m4n
|
|
January 06, 2017, 09:35:19 AM |
|
@Hadmart, have you tried with 16.10.3?
I've lost about 2 hours trying to get my 470s to work on Win 10. I kept getting freezes and cards weren't recognized properly. I think it also has to do with the fact that I heavily undervolted my cards. They work fine on my Win 7 (classic theme, black background).
I'm running 5 of them on my Win 7 now, haven't tried 6 cards yet. All with driver 16.10.3 (21.19.155.257).
|
|
|
|
h311m4n
|
|
January 06, 2017, 08:31:36 PM |
|
Hmmm, I'm having a weird issue.
On an H97 Anniversary, running 5x RX470s on a Windows 7 x64, no issues. I connect the 6th, getting to the Windows loading screen and I here one card after the other spinning it's fan then stopping, I'm counting 6. But soon after, the card in the last PCIe slot starts spinning again and the computer freezes. Removing one of the 6 cards and the computer boots fine.
I'm using driver 16.10.2, tried gen 1 and 2, no difference. Any advice?
|
|
|
|
m1n1ngP4d4w4n
Full Member
Offline
Activity: 224
Merit: 100
CryptoLearner
|
|
January 06, 2017, 08:41:26 PM |
|
Hmmm, I'm having a weird issue.
On an H97 Anniversary, running 5x RX470s on a Windows 7 x64, no issues. I connect the 6th, getting to the Windows loading screen and I here one card after the other spinning it's fan then stopping, I'm counting 6. But soon after, the card in the last PCIe slot starts spinning again and the computer freezes. Removing one of the 6 cards and the computer boots fine.
I'm using driver 16.10.2, tried gen 1 and 2, no difference. Any advice?
does this card work in another slot ? have you tried a different riser ? is another of the working card does the same in that 6th slot ? are you using stock bios ? if you flashed, maybe something went wrong. Have you used the 6x gpu mod before installing the 6th card, because it's needed on w7.
|
|
|
|
h311m4n
|
|
January 06, 2017, 10:27:16 PM |
|
Hmmm, I'm having a weird issue.
On an H97 Anniversary, running 5x RX470s on a Windows 7 x64, no issues. I connect the 6th, getting to the Windows loading screen and I here one card after the other spinning it's fan then stopping, I'm counting 6. But soon after, the card in the last PCIe slot starts spinning again and the computer freezes. Removing one of the 6 cards and the computer boots fine.
I'm using driver 16.10.2, tried gen 1 and 2, no difference. Any advice?
does this card work in another slot ? have you tried a different riser ? is another of the working card does the same in that 6th slot ? are you using stock bios ? if you flashed, maybe something went wrong. Have you used the 6x gpu mod before installing the 6th card, because it's needed on w7. Card is modded, but it's a solid mod so to speak. Different riser, different cable work. However yes, it's always is that last slot that the card has an issue (the bottom one). It'll work fine on 5 cards though. Yes I did install the mod once the 5 cards are working properly. Kinda out of ideas. I could try a bios update. Tomorrow I'll try a complete driver uninstall and then reinstall cards one at a time, see what's what. I gave a shot at Windows 10 the other day but ran into a whole bunch of issues...
|
|
|
|
h311m4n
|
|
January 07, 2017, 01:51:27 PM |
|
Ok so I got all 6 cards running on Windows 10, but initially, I was having the same issue: as soon as the 6th card was plugged in, the one in the slot closest to the CPU would start spinning again after Windows found it, and the computer would hang.
I fixed it by disabling the onboard lan in the BIOS, turning the computer back on, let Windows see and install the drivers for the card and boom, I could log on and all 6 cards were there. I then restarted, re-enabled the onboard lan and I'm now mining with 6 gpus.
I have a feeling that if I replug my Win7 SSD and do the same procedure, i'll get the 6 cards running.
|
|
|
|
m1n1ngP4d4w4n
Full Member
Offline
Activity: 224
Merit: 100
CryptoLearner
|
|
January 07, 2017, 05:34:33 PM |
|
Ok so I got all 6 cards running on Windows 10, but initially, I was having the same issue: as soon as the 6th card was plugged in, the one in the slot closest to the CPU would start spinning again after Windows found it, and the computer would hang.
I fixed it by disabling the onboard lan in the BIOS, turning the computer back on, let Windows see and install the drivers for the card and boom, I could log on and all 6 cards were there. I then restarted, re-enabled the onboard lan and I'm now mining with 6 gpus.
I have a feeling that if I replug my Win7 SSD and do the same procedure, i'll get the 6 cards running.
Just wondering, did you disabled the integrated onboard GPU if your motherboard have one ?
|
|
|
|
Dowper
|
|
January 08, 2017, 10:35:35 AM |
|
I have a feeling that if I replug my Win7 SSD and do the same procedure, i'll get the 6 cards running.
Test if you can, please.
|
|
|
|
h311m4n
|
|
January 08, 2017, 04:55:11 PM |
|
I have a feeling that if I replug my Win7 SSD and do the same procedure, i'll get the 6 cards running.
Test if you can, please. Sadly, that wasn't it. @m1n1ngP4d4w4n I did yes. I'me now mining on Windows 10. However, my rig would crash after about 30 minutes. Went to check on it, and it was off which indicated a shutdown had happened. Turns out, I had put 2 sticks of 4GB on that board and a BSOD was happening (Memory_management). Removed the second stick, put the first stick back in slot A1 and it's been mining for 6 hours straight now. So, it could be that this faulty ram was also causing the Windows 7 problem. I'll test it to see when I have some time on my hands. I must say, I didn't want to migrate to Win 10 but the fact that it can recognise 6 GPUs natively is pretty nice...
|
|
|
|
m1n1ngP4d4w4n
Full Member
Offline
Activity: 224
Merit: 100
CryptoLearner
|
|
January 08, 2017, 05:46:58 PM |
|
I have a feeling that if I replug my Win7 SSD and do the same procedure, i'll get the 6 cards running.
Test if you can, please. Sadly, that wasn't it. @m1n1ngP4d4w4n I did yes. I'me now mining on Windows 10. However, my rig would crash after about 30 minutes. Went to check on it, and it was off which indicated a shutdown had happened. Turns out, I had put 2 sticks of 4GB on that board and a BSOD was happening (Memory_management). Removed the second stick, put the first stick back in slot A1 and it's been mining for 6 hours straight now. So, it could be that this faulty ram was also causing the Windows 7 problem. I'll test it to see when I have some time on my hands. I must say, I didn't want to migrate to Win 10 but the fact that it can recognise 6 GPUs natively is pretty nice... Cool nice you got it to work Yeah W10 is pretty cool with big rig, make work so much easier
|
|
|
|
Lakici
Newbie
Offline
Activity: 23
Merit: 0
|
|
February 08, 2017, 01:45:11 PM |
|
Hi, I'm having troubles with win 10 as well. I've tried a bunch of different combinations, but I'm not able to run 6x470 with modded BIOS, only 4 of them are working.
On default BIOS everything is ok, but crimson 16.12.2 can't recognize modded BIOS, so I had to downgrade drivers. I'm trying a couple of drivers, but all with the same problem, only 4 with modded bios can run.
Any advice would be highly appreciated.
|
|
|
|
lbr (OP)
|
|
February 09, 2017, 02:01:41 PM |
|
Hi, I'm having troubles with win 10 as well. I've tried a bunch of different combinations, but I'm not able to run 6x470 with modded BIOS, only 4 of them are working.
On default BIOS everything is ok, but crimson 16.12.2 can't recognize modded BIOS, so I had to downgrade drivers. I'm trying a couple of drivers, but all with the same problem, only 4 with modded bios can run.
Any advice would be highly appreciated.
Afaik you need special driver for BIOS-modded 470 cards.
|
|
|
|
ntrader
|
|
February 09, 2017, 04:06:52 PM |
|
Hi, I'm having troubles with win 10 as well. I've tried a bunch of different combinations, but I'm not able to run 6x470 with modded BIOS, only 4 of them are working.
On default BIOS everything is ok, but crimson 16.12.2 can't recognize modded BIOS, so I had to downgrade drivers. I'm trying a couple of drivers, but all with the same problem, only 4 with modded bios can run.
Any advice would be highly appreciated.
Use 16.9.1 drivers, or atikmdag-patcher-1.4.4 for other versions.
|
|
|
|
avirdoz
Legendary
Offline
Activity: 1191
Merit: 1001
|
|
February 10, 2017, 12:18:16 AM |
|
Hi, I'm having troubles with win 10 as well. I've tried a bunch of different combinations, but I'm not able to run 6x470 with modded BIOS, only 4 of them are working.
On default BIOS everything is ok, but crimson 16.12.2 can't recognize modded BIOS, so I had to downgrade drivers. I'm trying a couple of drivers, but all with the same problem, only 4 with modded bios can run.
Any advice would be highly appreciated.
Use 16.9.1 drivers, or atikmdag-patcher-1.4.4 for other versions. 16.10.x work without patch too, not sure about 16.11.x
|
|
|
|
Lion BItcoin Shop
|
|
February 10, 2017, 02:31:00 AM |
|
just ask, do you use cpu miner too? during gpu mining? because i want to use my cpu to mining too, so i can get double profit.
which is better cpu for mining ?
|
|
|
|
|