the_joey_o (OP)
Newbie
Offline
Activity: 40
Merit: 0
|
|
August 26, 2012, 02:35:33 AM |
|
Hi all, I have 3 ATI 5770 Juniper GPUs in in a Win7 64-bit system. All 3 are detected and properly running in device manager, but when I try to use mining software, only 1 card is seen. This is a new phenomenon. There was a time when all 3 were detected. Then it went down to 2. Now just the 1. It doesn't appear that there are any driver updates that have come down (as the drivers are dated back to 2011). I've tried using guiminer & ufasoft.
Any suggestions?
|
|
|
|
|
|
Bitcoin addresses contain a checksum, so it is very unlikely that mistyping an address will cause you to lose money.
|
|
|
Advertised sites are not endorsed by the Bitcoin Forum. They may be unsafe, untrustworthy, or illegal in your jurisdiction.
|
|
|
|
segabtc
|
|
August 26, 2012, 03:10:10 AM |
|
need to check log of miners to see if one GPU locked up, because it will disable the GPU the next time you restart, and then check to see if the 2nd GPU locked up or hung up. That would explain how the cards are there but the miner doesn't see them. check in /BAMT/CONTROL/ACTIVE/ see what files are in there for the GPU that are missing.
|
|
|
|
the_joey_o (OP)
Newbie
Offline
Activity: 40
Merit: 0
|
|
August 26, 2012, 03:35:05 AM |
|
need to check log of miners to see if one GPU locked up, because it will disable the GPU the next time you restart, and then check to see if the 2nd GPU locked up or hung up. That would explain how the cards are there but the miner doesn't see them. check in /BAMT/CONTROL/ACTIVE/ see what files are in there for the GPU that are missing.
I don't think I'm following. I don't have a directory or file called BAMT. I found guiminer's log file, but I'm not sure what I should be looking for.
|
|
|
|
segabtc
|
|
August 26, 2012, 03:46:39 AM |
|
download cgminer and install that program, see if cgminer see the gpu's
|
|
|
|
the_joey_o (OP)
Newbie
Offline
Activity: 40
Merit: 0
|
|
August 26, 2012, 05:17:16 AM |
|
download cgminer and install that program, see if cgminer see the gpu's
Um. Am I missing something? Or do I need to compile cgminer from source to install it? I have been diligently RTFMing for compiling cgminer, but at the part where you first start to build the miner (after downloading and installing all the dependencies and source code and whatnot), I get the following error: The Joey-O@Mr_Compy ~/cgminer-2.7.4 $ adl.sh /bin/adl.sh: /bin/adl.sh: cannot execute binary file Now, when I first typed that command, I got an error saying something along the lines of: no such file exists. So, I went down to the "Optional - See Below" section mentioned in the WindowsBuild.txt file. I then followed those directions. I closed out the command line interface and opened it again, just in case. Tried the command adl.sh again, and got the above mentioned error. Suggestions?
|
|
|
|
|
the_joey_o (OP)
Newbie
Offline
Activity: 40
Merit: 0
|
|
August 26, 2012, 02:03:46 PM |
|
Yeah. I read through the readme about Windows builds. I don't see anything about that .sh file.
|
|
|
|
segabtc
|
|
August 26, 2012, 04:59:47 PM |
|
are you using windoze or *nix?
|
|
|
|
the_joey_o (OP)
Newbie
Offline
Activity: 40
Merit: 0
|
|
August 26, 2012, 05:13:13 PM |
|
are you using windoze or *nix?
Windows 7 64bit
|
|
|
|
the_joey_o (OP)
Newbie
Offline
Activity: 40
Merit: 0
|
|
August 26, 2012, 07:00:28 PM |
|
Still not getting anywhere with the cgminer .sh issue. I tried using the "File" command to see what info I can get on the adl.sh file, and this is what I got: The Joey-O@Mr_Compy ~ $ cd cgminer-2.7.4
The Joey-O@Mr_Compy ~/cgminer-2.7.4 $ adl.sh /mingw/bin/adl.sh: /mingw/bin/adl.sh: cannot execute binary file
The Joey-O@Mr_Compy ~/cgminer-2.7.4 $ file adl.sh adl.sh: ERROR: cannot open `adl.sh' (No such file or directory) Anybody know what I'm doing wrong?
|
|
|
|
segabtc
|
|
September 06, 2012, 02:15:13 AM |
|
Still not getting anywhere with the cgminer .sh issue. I tried using the "File" command to see what info I can get on the adl.sh file, and this is what I got: The Joey-O@Mr_Compy ~ $ cd cgminer-2.7.4
The Joey-O@Mr_Compy ~/cgminer-2.7.4 $ adl.sh /mingw/bin/adl.sh: /mingw/bin/adl.sh: cannot execute binary file
The Joey-O@Mr_Compy ~/cgminer-2.7.4 $ file adl.sh adl.sh: ERROR: cannot open `adl.sh' (No such file or directory) Anybody know what I'm doing wrong? in ~/cgminer-2.7.4 dir see if it list files look for adl.sh or ADL as directory. If not you dont have it installed/installed correctly. check that and get back to us.
|
|
|
|
GernMiester
|
|
September 17, 2012, 01:37:22 AM |
|
Use CGMiner.. Problems will likely just go away when you switch.
|
|
|
|
segabtc
|
|
September 19, 2012, 12:43:16 AM |
|
http://ck.kolivas.org/apps/cgminer/2.7/cgminer-2.7.0-win32.zipdownload that file unzip that file to a directory cgminer (remember where) go to that dir in windoze, look for cgminer.exe file right click on cgminer.exe look for "send to" click "desktop" click close window look on desktop for ICON named shortcut to cgminer double click on that and then get back to us.
|
|
|
|
|