|
zOU
|
 |
December 15, 2015, 11:27:21 PM |
|
Hi
I get:
USB management [P]ool management Settings [D]isplay options [Q]uit
0: AU3 0 : 225MHz 775mV | 56.95G / 55.49Gh/s WU:775.3/m
1: AU3 1 : 225MHz 775mV | 56.23G / 55.36Gh/s WU:772.6/m
is good?
They do zombie every 24 hours i have to power on/off though..
seems ok to me, but I'm 800km from mine so i can't check :p |
|
|
|
|
|
|
|
|
|
|
|
|
"The nature of Bitcoin is such that once version 0.1 was released, the
core design was set in stone for the rest of its lifetime." -- Satoshi
|
|
|
Advertised sites are not endorsed by the Bitcoin Forum. They may be unsafe, untrustworthy, or illegal in your jurisdiction.
|
|
|
|
|
|
|
Mikestang
Legendary
 Offline
Activity: 1274
Merit: 1000
|
|
December 15, 2015, 11:37:50 PM |
|
You think the Voltage i use is to high? I heared from another person that iam using a quit high voltage for this I think you should try 800 max voltage and see how it runs. Should be about as fast and a bit cooler. You can also add a fan to the bottom of the U3 to help cool it, here's mine:  [U]SB management [P]ool management [S]ettings [D]isplay options [Q]uit
0: AU3 0 : 225MHz 775mV | 56.95G / 55.49Gh/s WU:775.3/m
1: AU3 1 : 225MHz 775mV | 56.23G / 55.36Gh/s WU:772.6/m
is good?
They do zombie every 24 hours i have to power on/off though.. Yes, that looks good, although we could tell more if you did: then we could see your accepted shares and errors. Zombie is normal for the U3, I suggest you check out the R1 as a controller and get it from CrazyGuy with his custom firmware, https://bitcointalk.org/index.php?topic=612390.0, it basically solves the zombie problem. |
|
|
|
|
christiansenn
Newbie
Offline
Activity: 25
Merit: 0
|
|
December 16, 2015, 07:46:10 AM
Last edit: December 16, 2015, 07:49:02 AM by -ck |
|
[ U]SB management [P]ool management [ S]ettings [D]isplay options [Q]uit
0: AU3 0 : 225MHz 775mV | 60.62G / 56.73Gh/s WU:792.6/m A:495608 R:0 HW:13
1: AU3 1 : 225MHz 775mV | 58.98G / 56.73Gh/s WU:792.5/m A:522232 R:0 HW:10
|
|
|
|
|
durandal
Newbie
Offline
Activity: 4
Merit: 0
|
|
December 16, 2015, 11:22:35 AM |
|
Using the latest CGminer on linux compiled from git with --enable-icarus, I use --au3-freq 250 --au3-volt 810, which gets me a stable ~63ghs, without getting more than warm to the touch.
I've had a couple of zombie moments in the last week which seem to be precipitated by pool reboots. Might be coincidental!
|
|
|
|
|
|
zOU
|
|
December 20, 2015, 08:12:11 AM |
|
it looks like one of my U3 is dead:
- no hashing at all
- the red LED that used to blink when hashing is now permanently ON
- U3 is detected in windows/Linux
- windows cgminer sees it but says there's no drivers even though zadig has been installed
- linux: cgminer -n sees it, cgminer --benchmark just hangs....
I swapped power and USB cable with the same result
|
|
|
|
philspain
Newbie
Offline
Activity: 22
Merit: 0
|
|
December 20, 2015, 08:29:42 PM |
|
I'm new to mining I have just bought an Antminer U3 but can't seem to get it working it keeps saying
Probe of port com4 failed: timeout
Any help would be great
Thanks
|
|
|
|
|
|
|
philspain
Newbie
Offline
Activity: 22
Merit: 0
|
|
December 20, 2015, 09:00:26 PM |
|
Hello I have Windows 10 and an Antminer u3 I have been trying with cgminer but was getting frustrated so I'm trying BitMinter neither are working |
|
|
|
|
|
zOU
|
|
December 20, 2015, 09:06:39 PM |
|
Bitminter doesn't support the U3 Cgminer will work just fine, but you need to install the zadig driver before, check the post I linked earlier  |
|
|
|
philspain
Newbie
Offline
Activity: 22
Merit: 0
|
|
December 20, 2015, 09:13:09 PM |
|
Bitminter doesn't support the U3 Cgminer will work just fine, but you need to install the zadig driver before, check the post I linked earlier I used install the zadig drivers and tried with cgminer with no luck either getting no devices detected I don't know what i'm doing wrong |
|
|
|
|
|
zOU
|
|
December 20, 2015, 09:22:01 PM |
|
You're using cgminer 4.9.* ?
You can run
Cgminer -n (to list current devices)
Cgminer --benchmark (to test the device)
You can try reinstalling zadig drivers as administrator maybe.
You have the 2 solid Red LED on your U3 ?
|
|
|
|
philspain
Newbie
Offline
Activity: 22
Merit: 0
|
|
December 20, 2015, 09:37:26 PM
Last edit: December 20, 2015, 09:50:29 PM by philspain |
|
You're using cgminer 4.9.* ?
You can run
Cgminer -n (to list current devices)
Cgminer --benchmark (to test the device)
You can try reinstalling zadig drivers as administrator maybe.
You have the 2 solid Red LED on your U3 ?
I'm using cgminer 4.9.2 tried a few reinstalled the drivers no difference and rebooted tried with cgminer -n seems to see it but close window down can only see one red led |
|
|
|
|
|
zOU
|
|
December 20, 2015, 10:12:24 PM |
|
Run it from a command line, not from start menu |
|
|
|
philspain
Newbie
Offline
Activity: 22
Merit: 0
|
|
December 20, 2015, 10:21:57 PM
Last edit: December 21, 2015, 05:34:54 AM by philspain |
|
Run it from a command line, not from start menu when I run cgminer - n this is what i get Microsoft Windows [Version 10.0.10240] (c) 2015 Microsoft Corporation. All rights reserved. cgminer -n [2015-12-20 23:19:40] USB all: found 7 devices - listing known devices .USB dev 0: Bus 2 Device 2 ID: 10c4:ea60 Manufacturer: 'Silicon Labs' Product: 'CP2102 USB to UART Bridge Controller' [2015-12-20 23:19:41] 1 known USB devices Any Ideas anyone please it is frustrating me now |
|
|
|
|
durandal
Newbie
Offline
Activity: 4
Merit: 0
|
|
December 21, 2015, 12:17:00 PM |
|
Have you read the manual? It lists the following command (but I've edited out the pool options - see if that works, and then add the pools from inside CGMiner and then 'w'rite the config file when it's up and running): cgminer --bmsc-options 115200:0.54 --bmsc-voltage 0830 --bmsc-freq 0982 The voltage/freq values can be modified according to the tables listed in the manual, but stick with the given ones for the moment. Just to be sure, you are hitting the windows key, typing 'cmd' and using the command line that way? |
|
|
|
|
|
zOU
|
|
December 21, 2015, 12:30:52 PM |
|
The bsmc option has been deprecated a while ago.
Cgminer --benchmark should detect and hash at 56Ghs if the zadig driver has been installed and the device visible with cgminer -n.
Cgminer ReadMe lists the new options for the U3
(--au3-freq or something like this)
|
|
|
|
|
Jake36
|
|
December 21, 2015, 01:06:21 PM |
|
The bsmc option has been deprecated a while ago.
Cgminer --benchmark should detect and hash at 56Ghs if the zadig driver has been installed and the device visible with cgminer -n.
Cgminer ReadMe lists the new options for the U3
(--au3-freq or something like this)
If I remember right, cgminer defaults to --au3-freq 225 and --au3-volt 775, so no need to add that in "yet". Also I think there was a problem where cgminer 4.9.1 (or was it 4.9.0) did not work with the U3's for some, so philspain make sure you are using cgminer 4.9.2. And lastly (anyone else that has tried), didn't Windows 10 change something, to where zagdig would not work??? |
|
|
|
|
philspain
Newbie
Offline
Activity: 22
Merit: 0
|
|
December 21, 2015, 02:21:40 PM |
|
Thank you all for your help I will try these this afternoon and get back to you.
|
|
|
|
|
philspain
Newbie
Offline
Activity: 22
Merit: 0
|
|
December 21, 2015, 02:48:37 PM |
|
this is what happens when I try cgminer --benchmark
cgminer version 4.9.2 - Started: [2015-12-21 15:47:08]
--------------------------------------------------------------------------------
(5s):0.000 (1m):0.000 (5m):0.000 (15m):0.000 (avg):0.000h/s
A:0 R:0 HW:0 WU:0.0/m
Connected to Benchmark diff ? without LP as user Benchmark
Block: ... Diff: Started: Best share: 0
--------------------------------------------------------------------------------
SB management [P]ool management ettings [D]isplay options [Q]uit
--------------------------------------------------------------------------------
[2015-12-21 15:47:01] Started cgminer 4.9.2
[2015-12-21 15:47:08] No devices detected!
[2015-12-21 15:47:08] Waiting for USB hotplug devices or press q to quit
|
|
|
|
|
philspain
Newbie
Offline
Activity: 22
Merit: 0
|
|
December 21, 2015, 03:16:34 PM |
|
Sorry tried all this still no luck
cgminer version 4.9.2 - Started: [2015-12-21 16:13:51]
--------------------------------------------------------------------------------
(5s):0.000 (1m):0.000 (5m):0.000 (15m):0.000 (avg):0.000h/s
A:0 R:0 HW:0 WU:0.0/m
Connected to Benchmark diff ? without LP as user Benchmark
Block: ... Diff: Started: Best share: 0
--------------------------------------------------------------------------------
SB management [P]ool management ettings [D]isplay options [Q]uit
--------------------------------------------------------------------------------
[2015-12-21 16:13:44] Started cgminer 4.9.2
[2015-12-21 16:13:51] No devices detected!
[2015-12-21 16:13:51] Waiting for USB devices or press q to quit
|
|
|
|
|
|
