|
Title: zadig driver no longer working... Failed to initalise (Incorrect device) Post by: spazzdla on August 05, 2015, 10:23:20 PM I've been mining with an Rbox for some time.. I just formated my computer.. now after I installed the driver via zadig it's giving me some crazy ass errors...
"Icarus detect <8.2> failed to initialise <incorrect device?> anyone know wtf this means? I followed https://www.youtube.com/watch?v=cATJVLb1P1A&list=UUcqRbsp96-Z3BAu_oSG-TCA worked every time except now...... UPDATE Got it!!!!!! ahh yaaaa ROLL BACK THE DRIVER IF THIS HAPPENS TO YOU!!!! Title: Re: zadig driver no longer working... Failed to initalise (Incorrect device) Post by: KWH on August 05, 2015, 10:26:59 PM I've been mining with an Rbox for some time.. I just formated my computer.. now after I installed the driver via zadig it's giving me some crazy ass errors... "Icarus detect <8.2> failed to initialise <incorrect device?> anyone know wtf this means? I followed https://www.youtube.com/watch?v=cATJVLb1P1A&list=UUcqRbsp96-Z3BAu_oSG-TCA worked every time except now...... Had the same issue. I unplugged all miners but 1, reinstalled the Zadig drivers and one at a time, plugged the devices back into the PC. Look in your Device Manager to confirm they are all there. If not, go through the procedure again, one at a time. Sometimes I have to unplug power, wait a few seconds then plug back in. Usually they start again with in 1-3 minutes. EDIT: Hat tip to dogie Title: Re: zadig driver no longer working... Failed to initalise (Incorrect device) Post by: spazzdla on August 05, 2015, 10:34:48 PM I've been mining with an Rbox for some time.. I just formated my computer.. now after I installed the driver via zadig it's giving me some crazy ass errors... "Icarus detect <8.2> failed to initialise <incorrect device?> anyone know wtf this means? I followed https://www.youtube.com/watch?v=cATJVLb1P1A&list=UUcqRbsp96-Z3BAu_oSG-TCA worked every time except now...... Had the same issue. I unplugged all miners but 1, reinstalled the Zadig drivers and one at a time, plugged the devices back into the PC. Look in your Device Manager to confirm they are all there. If not, go through the procedure again, one at a time. Sometimes I have to unplug power, wait a few seconds then plug back in. Usually they start again with in 1-3 minutes. did you uninstall them via computer manager? Title: Re: zadig driver no longer working... Failed to initalise (Incorrect device) Post by: KWH on August 05, 2015, 10:35:46 PM No, but when they were not working, they did not show in DM. Once they show in DM, they should work.
Title: Re: zadig driver no longer working... Failed to initalise (Incorrect device) Post by: spazzdla on August 05, 2015, 10:39:42 PM It keeps fucking moving it to the fucking ports.. it's.. how do I stop the POS from thinking it's a fucking serial connection?\
It keeps changing it's dumbass self to "Silicon labs CP210x USB toUART bridge(COM3) Title: Re: zadig driver no longer working... Failed to initalise (Incorrect device) Post by: KWH on August 05, 2015, 10:40:41 PM It keeps fucking moving it to the fucking ports.. it's.. how do I stop the POS from thinking it's a fucking serial connection? Are you seeing this before or after the Zadig installation? Title: Re: zadig driver no longer working... Failed to initalise (Incorrect device) Post by: spazzdla on August 05, 2015, 10:42:25 PM It keeps fucking moving it to the fucking ports.. it's.. how do I stop the POS from thinking it's a fucking serial connection? Are you seeing this before or after the Zadig installation? It just keeps auto installing something.... :S I don't think the zadig is taking effect... Title: Re: zadig driver no longer working... Failed to initalise (Incorrect device) Post by: KWH on August 05, 2015, 10:43:16 PM It keeps fucking moving it to the fucking ports.. it's.. how do I stop the POS from thinking it's a fucking serial connection? Are you seeing this before or after the Zadig installation? It just keeps auto installing something.... :S Plug 1 in and run the Zadig driver. Check DM and confirm the miner is there under USB devices. Title: Re: zadig driver no longer working... Failed to initalise (Incorrect device) Post by: spazzdla on August 05, 2015, 10:45:09 PM It keeps fucking moving it to the fucking ports.. it's.. how do I stop the POS from thinking it's a fucking serial connection? Are you seeing this before or after the Zadig installation? It just keeps auto installing something.... :S Plug 1 in and run the Zadig driver. Check DM and confirm the miner is there under USB devices. It keeps jumping to the serial port..... Every time I run the program Title: Re: zadig driver no longer working... Failed to initalise (Incorrect device) Post by: spazzdla on August 05, 2015, 10:49:54 PM Removed all drivers,
hard shutdown computer re-install driver... keeps moving to port section.. "Silicon labs cp210x USB to UART Bridge (Com4)" still failing on it doesn't know device Title: Re: zadig driver no longer working... Failed to initalise (Incorrect device) Post by: KWH on August 05, 2015, 10:50:29 PM It keeps fucking moving it to the fucking ports.. it's.. how do I stop the POS from thinking it's a fucking serial connection? Are you seeing this before or after the Zadig installation? It just keeps auto installing something.... :S Plug 1 in and run the Zadig driver. Check DM and confirm the miner is there under USB devices. It keeps jumping to the serial port..... Every time I run the program Are you going to the Options menu and select List All Devices? Then reinstall? Mine show as: CP2102 USB to UART Bridge Controller. Title: Re: zadig driver no longer working... Failed to initalise (Incorrect device) Post by: KWH on August 05, 2015, 10:52:34 PM Removed all drivers, hard shutdown computer re-install driver... keeps moving to port section.. "Silicon labs cp210x USB to UART Bridge (Com4)" still failing on it doesn't know device You can try to uninstall the drivers, and remove the actual driver from the system then reinstall. Title: Re: zadig driver no longer working... Failed to initalise (Incorrect device) Post by: spazzdla on August 05, 2015, 11:06:54 PM Removed all drivers, hard shutdown computer re-install driver... keeps moving to port section.. "Silicon labs cp210x USB to UART Bridge (Com4)" still failing on it doesn't know device You can try to uninstall the drivers, and remove the actual driver from the system then reinstall. Via the device manager?? I have it running now on my second hard drive... This "silicon labs" bullshit is messing up my stuff.. Do I have to regedit.. god I hope not. Title: Re: zadig driver no longer working... Failed to initalise (Incorrect device) Post by: KWH on August 05, 2015, 11:07:53 PM Removed all drivers, hard shutdown computer re-install driver... keeps moving to port section.. "Silicon labs cp210x USB to UART Bridge (Com4)" still failing on it doesn't know device You can try to uninstall the drivers, and remove the actual driver from the system then reinstall. Via the device manager?? I have it running now on my second hard drive... This "silicon labs" bullshit is messing up my stuff.. Do I have to regedit.. god I hope not. I didn't have to, just removed from DM and it had an option to completely remove (uninstall). |