|
Title: ANTMINER S7 BATCH 2 - VS - ANTMINER S7 BATCH 3 Post by: marvykkio on October 03, 2015, 06:59:02 PM ANTMINER S7 BATCH 3
S7 Specifications: 1. Hash Rate: 4.86 TH/s ±5% 2. Power Consumption: 1210 W (at the wall, with APW3, 93% efficiency, 25C ambient temp) 3. Power Efficiency: 0.25 J/GH (at the wall, with APW3, 93% efficiency, 25°C ambient temp) 4. Rated Voltage: 12.0V+5%, should not be less than 12.0V 5. Chip quantity per unit: 162x BM1385 6. Dimensions: 301mm(L)*123mm(W)*155mm(H) 7. Cooling: 2x 12038 fan 8. Operating Temperature: 0 °C to 40 °C 9. Network Connection: Ethernet 10. Default Frequency: 600M _______________________________________________________________________________ _______________________________________- ANTMINER S7 BATCH 2 S7 Specifiche tecniche: 1. Hash Voto: 4.66 TH / s ± 5% 2. Consumo: 1160 W (il muro, con APW3, efficienza 93%, 25C ambient temp) 3. Efficienza energetica: 0.25 J / GH (il muro, con APW3, efficienza 93%, 25 ° C temperatura ambiente) 4. Tensione nominale: 12.0V + 5%, non deve essere inferiore a 12.0V 5. Chip quantità per unità: 162x BM1385 6. Dimensioni: 301mm (L) * 123 millimetri (W) * 155 millimetri (H) 7. Raffreddamento: 2x 12038 fan Temperatura 8. esercizio: 0 ° C a 40 ° C 9. Connessione di rete: Ethernet 10. Default Frequency: 575M who tells us that buying antminer s7 batch 3 (4.86 th / s They send antminer s7 batch 2? (4,66 th / s) amount of chips are equal, the difference is in default frequency 575 MB vs. 600 MB? so if I buy the second batch, and put the firmware of batch 3? I can do it? Since the amount of the chips are equal? correct me if I'm wrong. Title: Re: ANTMINER S7 BATCH 2 - VS - ANTMINER S7 BATCH 3 Post by: notlist3d on October 03, 2015, 07:03:19 PM who tells us that buying antminer s7 batch 3 (4.86 th / s They send antminer s7 batch 2? (4,66 th / s) You might merge this with the other S7 thread as it is not really needed a thread of its own. But that is up to you. As far as who tells you it would be bitmain. You would get a email if it's like batch one and they asked if it was ok to send a lower speed miner. But I suspect with different batches they do pretty good at getting the right speed to people that order. Title: Re: ANTMINER S7 BATCH 2 - VS - ANTMINER S7 BATCH 3 Post by: RichBC on October 03, 2015, 08:25:09 PM amount of chips are equal, the difference is in default frequency 575 MB vs. 600 MB? so if I buy the second batch, and put the firmware of batch 3? I can do it? Since the amount of the chips are equal? correct me if I'm wrong. Not quite sure why you are raising this in a new thread as it's all covered in the main thread? However it's not a firmware issue, all batches 1,2 & 3 can be run at 600MHz or 575MHz. The issue is that some units, Batch 2, Bitmain have decided to derate to 575MHz presumably because the HW error rate at 600MHz was unacceptable? Rich Title: Re: ANTMINER S7 BATCH 2 - VS - ANTMINER S7 BATCH 3 Post by: marvykkio on October 04, 2015, 08:57:06 AM rate of hardware failures? same materials, same amount of chips,? assembled by the same people? but what you're saying?You tell me how do you to realize if they send you after you buy 2 batch 3 batch? that the difference are 20 gh / s?
PS: do not worry about the thread, you can quit at any time Title: Re: ANTMINER S7 BATCH 2 - VS - ANTMINER S7 BATCH 3 Post by: Tupsu on October 04, 2015, 09:52:10 AM ... that the difference are 20 gh / s? PS: do not worry about the thread, you can quit at any time Why do you feel concerned about it, if the difference is only 20 gh / s ? Your math is terrible. Make yourself clear , how many GH/s is in one TH/s. The best you can do with your thread, is to put it in the lock. Title: Re: ANTMINER S7 BATCH 2 - VS - ANTMINER S7 BATCH 3 Post by: marvykkio on October 04, 2015, 11:30:45 AM batch 2 4,66 th/s
batch 3 4,86 th/s what is the difference? Title: Re: ANTMINER S7 BATCH 2 - VS - ANTMINER S7 BATCH 3 Post by: SunnyIgor on October 04, 2015, 12:11:03 PM Will batch 1 (still waiting :-X) at least be the 4.86?
Because i heard some were getting commpensation because of only 4.66... Title: Re: ANTMINER S7 BATCH 2 - VS - ANTMINER S7 BATCH 3 Post by: notlist3d on October 04, 2015, 06:29:17 PM batch 2 4,66 th/s batch 3 4,86 th/s what is the difference? The difference is some miners under preform. It was enought that it did not fit in standard +/- of hashrate. So... they split it into two batches. One is cheaper and slower. Other is higher and faster. Some in batch one got the slower and got a little compensation. But speed is the difference along with price. |