Bitcoin Forum

i'm building and selling these if someone is interested

price: 0.08 btc + shipping

https://ip.bitcointalk.org/?u=https%3A%2F%2Fs10.postimg.org%2Fjxx7gj9qx%2FRIG_FINALE.jpg&t=572&c=ldNZRaTMux4F-w

you can screw both psu and ssd to the rig, MB is screwed with M3 nylon screw, 100% insulated, that white wireway is for insulating the bottom of the gpu when you place over it

Got one from this guy through ebay (didn't know he operated here) and it's really good quality stuff :)

Just be carefull with Nitro 470 you'll have to bend the riser usb cable, no problem with ref 480

you are the french guy? good, perhaps the risers usb cables touched the "white" bar? i can change that if this is a problem, i don't use usb risers so i did not know about this possible issue

That's me, here's what I'm talking about : https://drive.google.com/file/d/0B1pT04MB3X0aSUo5NkFvMlZwaDQ/view?usp=sharing

Don't have a picture of the 470 because it was a shitty series and burned out, it's in the shop now :)

yeah i knew about that possible issue, in fact i moved that bar 2 cm toward the right, but it seems that it was not enough, those risers are very long

mh i'll think about a new solution or just move even more that bar on the right(i didn't this because for small gpu it would be an issue to have that bar too far away, i don't want that the gpu angle toward the bottom)

can you tell me if 2cm would be enough so the risers will not bend that way?

Well IMO there are 2 options, either you move the bar 2_3cm to the back, or you put a les thick (>1cm) bar at this place, option 2 is better because then you won't have smaller cards hangign :)

I hope this was clear, I'll make a drawing if it's not

Cheers,
Q.

yeah those were my two options at least, but the small bar can not be attached to the connectors, so you need to screw it, but not above the other side bars, or you will end up with the card not on the same plane, due to the thickness

Okay actually I'm a moron, I just have tu put the card a little up so that it's the USB and not the card resting on the frame, it's still all fine :)

PS : enjoy the bump mate !

anyway i fixed that issue, with the next design, better placement for the psu and a flat bar instead of square one, i only have this bad resolution image for now

https://s10.postimg.org/jxx7gj9qx/RIG_FINALE.jpg

I'd like to leave a big vouch for this man. Received my frame and assembled. The frame itself is aesthetically pleasing, and I seated my rig components with no issues. Will be buying more from him in the future.

tnx for the opinion, and the bump

pictures are also welcome for others to see how it looks assembled, i can't do it because ironically i don't have this frame, mine is different because it was my first design

price reduced to 0.12 due to btc rise

Here are some pictures :
(still don't know how to put them in the body)

https://drive.google.com/open?id=0B1pT04MB3X0adl9jalpSdXg5Rkk
https://drive.google.com/open?id=0B1pT04MB3X0acUtReUdWcVBsVnc

Cheers !

Can you make them stackable?

Been wondering this myself

yes but it need more materials, it will be like mine

https://s3.postimg.org/w7wii80eb/rig_1.jpg

but to be honest it's better if you buy a shelf like this

https://www.amazon.com/Gracious-Living-4-Shelf-Light-Shelf/dp/B0083ESFAM/ref=sr_1_5?ie=UTF8&qid=1477031788&sr=8-5&keywords=plastic+shelf

that can handle many of them, than stacking one on top of each other, it's more easy to move in this way

Option 3:

Make the bar that holds the back part of the gpu adjustable with a simple cut out on the inside the frame so you can slide it to the position you need and tighten a screw :)

thanks!

Where are you located? Just wondering about the shipping cost to Toronto, Canada - postal code M6S 3T8?

i'm just sending to a same location in canada, shipping is a bit high, but it depend on how many you order, maybe it can be around $35 only...just checked again, it's 47 euro


but then it would look ugly with the fissure in the alluminium bar, i think the last design do not have any problem anymore

interested. willing to buy!! whats the awesome total price inc post to aus. will buy alot more in the future, like to see how this will go out about. pm if you can

ok tell me in pm about how many you are interested and i'll build and ship them to you, just tell me your country so i can tell you the shipping cost

up

Where are you shipping from?

I'd also like to know where you're shipping from, and I will definitely take at least one as a test for now, more later if the test goes well. let me know. Thanks!

from italy, bears in mind that i don't have them ready so you need to wait for the pieces to be bought first

but since with the last order i ordered two(and he want one only) i'll have at least one ready to be shipped this week

Ahh. TY. Too far.

Damn, Italy may kill the deal for me... I'm pretty sure it will actually... if that was in the OP sorry I didn't see it. Thanks anyway!

it depend where do you live, but for america it's 50 euro the shipping, so yes in that case it would kill it, still the total would be 120 euro, i see users on ebay selling for the same price frame that are worse than mine

Hi, can you do a bar or something to be able to hold 3 120mm/140mm fans in front of the gpu's?
https://s3.postimg.org/w7wii80eb/rig_1.jpg
Instead of zip ties. (Good idea)

hi, it's already there, it's the bar in front of the white bar, what i used to secure the 3 x 140mm fan are cable ties, not screw, you just pass one inside the screw hole of the fan and wrap it to the aluminium bar, it's pretty simple and do not require drilling

https://s27.postimg.org/wi65qt00j/download_2.jpg

in that image you posted you can't see the cable ties, because they are wrapped to the 6 pin pcie, look closely to see them

here

https://s27.postimg.org/c8hcsxyyr/download_3.jpg

price updated to reflect btc value

This guy built many frames for me, all of very good quality. Here is a picture of one of my rigs:

https://i.imgur.com/oHujivF.jpg

so you really have 72 gpu?  ;D

A bit less than that, as I haven't mounted cards on two frames yet :) Might plan on getting more frames from you in the future if mining profitability looks better.

is the "last design" pictured in this thread, curious to see it.

thanks!

yeah the photo is in the first page scroll down a bit

...ok i've added it in the first post, that is the final product that you will receive, when you order one


what is your electricity 5 cent? this might explain why you you are going big

My electricity cost is 18.5 cents/kWh with additional data center fees. My profit margin is minimal, but alright.

still available if someone is interested

How much for one frame incl. shipping cost to Germany?

i missed this post, was busy lately...70 euro for the frame + 15 euro for shipping, 85 euro total, that is 0.078, i can do 0.075 depend on the btc price