Bitcoin Forum

Hello Guys,

i mined LBRY for 21 hours with arround 500 mh/s.

on whattomine it says i should get 11,23 LBRY in 24 Hours meaning around 400k satoshi.
After 21 hours of mining i end up with 6,74 LBRY. (arround 220k satoshi)
Im mining on suprnova with the EWBF miner.

Where is my mistake why do i get so much less as i expected to get on whattomine.

Please help me out :).

Thanks

Is that counting unconfirmed LBC on suprnova? Do you have it set to pay out automatically every so many LBC on suprnova? What is your .bat file for your miner?

difficulty is going up so hard and down so whattomine isn't as accurate as you can see

No i didnt set an automatic payout im pretty sure im fine with my settings at suprnova it was my first time mining LBRY and in  have total earning of 6,6 LBRY till now.
 
The Bat im using is the following:

ccminerAlexis78  -a lbry -o stratum+tcp://lbry.suprnova.cc:6256  -u Astasu.Astasu -p x -i 25

Im getting pretty close to 500 mh/s all the time.


Okay i understand that and i think so too. But i averange nearly half not even close to whattomine this cant be the difficulty only or?

When i mine DGB on Skein im getting nearly exactly that amount, thats displayed on whattomine.

Sounds like the rest could still be unconfirmed on suprnova. Check your unconfirmed coins on your dashboard.

I have 0,16 unconfirmed.

Is someone else mining LBRY on suprnova? Since there is so much hashpower on it i think im wrong but i dont know where?
Is my miner or suprnova pool an issue here?

Even though my hashrate on the miner stays at a constant 500-505 the reported hashrate on the supernova dashboard seems to vary wildly from 200-600 and averages around the 350... not sure why still trying to find answers on this one

Same exact scenarion, i just moved to Nicehash so they can decide what is more profitible for my TI card and get paid in BTC.

the 'realtime' hash rate that you get from the mining pools, bet it surprnova or otherwise, will never be accurate.  My guess is that the latency, confirmed numbers, dropped packets, etc all contribute to a real time stat that ends up being 50-150% off.   You need to take the avg of a 12-24 hour period so that the numbers are more reflective of real numbers.   I have a sneaking suspicion that the inaccurate real time numbers are either by design (for nefarious reasons) or lazy programming.

Myself, I have a local real time hash rate of 3600 (7 1080 TI's) and avging about 100 LBC's/day using suprnova, which seems about right.   Was using zpool before and using their auto exchange to BTC, another layer of complexity that I wasn't sure of.

I'm getting about 10 LBC/day with each 1080 ti at 470.
80%tdp.
Core+120
Mem 0
Temp 60°
200w
How is your setup to get +500?

I bought the beastly, overclocked 1080 TI AMP Extreme's.  These things run quiet, cool, and fast.


85% TDP
core +75 (on top of being OC'ed out of the box)
mem -502
temp 58-68
260w <---sucking more juice

each card is getting 515-535 mh/s

Iv got the same problem with supernova pool and ccminer.
Yestarday was the worst day i mine 15 LBC less then the day before, same options. About 450-500 Mh/s per card.
This is my setup https://i.imgur.com/Qdx5ca4.png and it mine only 35-40 LBC per day on supernova, i dont know whats the problem it shoulde be way more.

Try coinmine.pl

It may be difficulty change

experiment with difficulty setting in your miner program. It makes a huge difference. try setting it to d=4 or d=8 or d=16 and see which pays out more for you. ccminer x64 d=2 on my settings.

Hi, may I know how to set the difficulty in miner? I am using ccminer 2.0, 5x gtx 1060 6gb hashrate 990mh/s

What diff amount should I set in miner base on this spec?

you can set your worker diff by using the password field in your bat file.  instead of the usual -p x, use -p d=256 etc. 

they actually have a note explaining it that is always on top of the dashboard, just look up :)

You can now use d=? in worker password field for static diff. For example "d=16" gives you a static diff of 16:
./sgminer -k lbry -o stratum+tcp://lbry.suprnova.cc:6256 -u suprnova.1 -p d=16 -I 21 -g 4 -w 256

500mh one single 1080ti? Why whattomine says 46 mh on 1080ti?

500 is correct i'm getting 515-520 with each of my Asus Strix.

Idk.... are u sure 500?
Because i get 18.6 mh on my 1060 and 23 on my rx 480
Too much difference


Whattomine and nicehash profit calculation they both say 1080ti hashrate is 46mh 🤔🤔

Dude are you serious? It's LBC not ETH...

Hmm, the calculators say its 470Mh/s or 0.47Gh/s

Yes sorry my bad i was watching lbr2 or something
Instead it is lbry my 1060 is 128mh

Well 500 is a good profit i think is better than eth which u do about 37?

Lbry is totally different than Lyra2Rev2.

This algorithm is profitable right now, since the coin is 45% up in coinmarketcap.

it's because of two things one is the diff that continue to go up and the other is because of the variance of the hashrate if the pool, suprnova can't find all the block

Right now running d=8 with 3 evga gtx 1080...approximately 23-27 coins per day.

I don't think d=8 is good, that's too low. d=32 is the lowest I think for whole rig I would say you need more. I think CCminer recommend for whole rig d=256, default is d=128. You can play with intensity. I've post some info on FB LBRY mining page https://www.facebook.com/groups/1961052344127892/

I get 315MHASH stable with oc on the gtx 1070. You should be able to get 550MHASH on the 1080ti.

use LBRY sp-mod

-500 on the memory clock 100% tdp or higher. 120%. And then overclock the core as much as possible.

IDK what hashrates are on 10 series, but I've tested LBRY with my laptop's 860m and I get 51MH/s with CCminer 2.0 but with your SP mod only 41MH/s. I've used both newest release maybe it could be better if I've build it with Cuda 8.0?

Hello all,  im new in mining and my 1080 ti in Claymore Dual Eth- Lbry shows me 32 Mhs on eth, and only 17mh on LBC, this is very far from the 470 mh that sais whattomine, and the speeds that all of you report on LBC.

¿Please can anyone help me?, any advice would be very appreciated.
Thank you

That's dual. Mine it solo with ccminer if you want the big hashrate. I pull around 245 mh/s on gtx 1070's.

Another question. Would dual zec/lbc ever be possible? Seems would be very profitable for gtx 1070s, 1080s, and 1080 tis.

LBC is able to be dual mined because ETH is memory intensive while both ZEC and LBC is core intensive.

NiceHash calc for 1080Ti on Lbry is 0.47Gh/s... so thats 470MH/s yea?

*edit* - someone posted this already

yeah here is hoping someone picks up on this due to zec diff increase

i get 760h/s from mine and would love to see them dual mine and use more of these epic cards

Yes, I love LBRY!

It has an active community, lots of content publishers and unlike most other crypto projects, LBRY has working software! (it is in beta, but has come a pretty long way)

You can see the bitcointalk-thread of our LBRY community-page at:
https://bitcointalk.org/index.php?topic=2665793 (https://bitcointalk.org/index.php?topic=2665793)

Or just go to https://LBRY.Community (https://LBRY.Community)

You can win contests now! (up to 8000 LBC which is over 5000$ as of 29. Dec 2017)