|
Title: Newbie here has a few questions. Post by: Magicmike514 on November 15, 2013, 11:29:55 PM Hi there my name is Mike,
I was wondering about the MiniRig from butterfly labs. Does anyone know which torx is used to take off the case? Thanks, Mike Title: Re: Newbie here has a few questions. Post by: CoinGeneral on November 15, 2013, 11:35:39 PM Hey Mike you don't have to post like it's a letter to someone, it's just a random forum
so you there's no formatting rules or anything Title: Re: Newbie here has a few questions. Post by: Magicmike514 on November 15, 2013, 11:39:14 PM Hey Mike you don't have to post like it's a letter to someone, it's just a random forum so you there's no formatting rules or anything oh ok sorry :/ just trying to figure out how to open the case LOL. But i can't post in the technical mining section Title: Re: Newbie here has a few questions. Post by: CoinGeneral on November 15, 2013, 11:44:31 PM Hey Mike you don't have to post like it's a letter to someone, it's just a random forum so you there's no formatting rules or anything oh ok sorry :/ just trying to figure out how to open the case LOL. But i can't post in the technical mining section Yeah I'm not sure what torx it is, they should have just used Phillip's screwdriver sizes, that would have made the most sense Title: Re: Newbie here has a few questions. Post by: hieroglyph on November 16, 2013, 02:41:51 PM I couldn't guess but I'd contact there customer support for a question like that if I were you.
Title: Re: Newbie here has a few questions. Post by: Magicmike514 on November 16, 2013, 05:52:33 PM I couldn't guess but I'd contact there customer support for a question like that if I were you. [/quot They don't have a customer support Title: Re: Newbie here has a few questions. Post by: duravello on November 16, 2013, 05:57:07 PM Try
https://forums.butterflylabs.com/ Not many BFL fans here in Newbie section Title: Re: Newbie here has a few questions. Post by: Maxbet on November 16, 2013, 06:03:56 PM Hey Mike you don't have to post like it's a letter to someone, it's just a random forum so you there's no formatting rules or anything oh ok sorry :/ just trying to figure out how to open the case LOL. But i can't post in the technical mining section Yeah I'm not sure what torx it is, they should have just used Phillip's screwdriver sizes, that would have made the most sense In fact, I don't even buy philips screws anymore if I can get my hands on the same size torx scews. More on topic: most hardware stores have sets of ~10 torx bits for a couple of bucks. Since you probably need to buy 1 bit for your rig anyway why not buy the set. Title: Re: Newbie here has a few questions. Post by: Magicmike514 on November 16, 2013, 06:21:04 PM Hey Mike you don't have to post like it's a letter to someone, it's just a random forum so you there's no formatting rules or anything oh ok sorry :/ just trying to figure out how to open the case LOL. But i can't post in the technical mining section Yeah I'm not sure what torx it is, they should have just used Phillip's screwdriver sizes, that would have made the most sense In fact, I don't even buy philips screws anymore if I can get my hands on the same size torx scews. More on topic: most hardware stores have sets of ~10 torx bits for a couple of bucks. Since you probably need to buy 1 bit for your rig anyway why not buy the set. I bought a whole set of hex and torx bits but the torx was only able to take two off the back. The side screws appear to be hexagonal and i get a 3/32 to fit inside and there is good tension but when i turn i hear a snap noise and there is no tension after sort of like the feeling when a screw becomes stripped. |