My board is just arrived too! First screenshot from hashing :
|
|
|
I have ordered from the 30' piece hex8 with the better express shipping, this shipping was 46 euro. But my package is still in sofia soon 2 days. . Why is this express delivery? For more price i want much more speed ^^ i know very well that technobit cannot do anything with this, but i want answers. The shipping destination is hungary.
Shipment number: 60074379593 (DPD Parcel Label No: 16602410229650) Date Operation Settlement 2014-02-11 18:32:14 Courier Pick-up SOFIA 2014-02-11 19:23:32 Received in Office SOFIA * A delay in the shipment status update may be expected for international deliveries.
Before this i have hex8a2 ordered with regurar shipping and was 4day: Shipment number: 60067117726 (DPD Parcel Label No: 16602410220681) Date Operation Settlement 2014-01-10 17:34:22 Courier Pick-up SOFIA 2014-01-10 18:13:45 Received in Office SOFIA 2014-01-10 19:47:28 Processed in Office 0068-Sofia, BULGARIA 2014-01-13 08:27:17 Processed in Office 0066-Budapest, HUNGARY 2014-01-14 06:23:27 Arrival Scan 1657-Kapuvar, HUNGARY 2014-01-14 07:02:04 Out for Delivery 1657-Kapuvar, HUNGARY 2014-01-14 12:13:27 Delivered Recipient RAJCI 1657-Kapuvar, HUNGARY * A delay in the shipment status update may be expected for international deliveries
When the hex8 not arrive in this week, i fall from many btc..
|
|
|
So, today is 10. feb. You would today post the boards?
|
|
|
Yeah i wanna know this too. Marto are the 30x pre-production units ready to ship on Monday 10th Feb? I've got 2 in that batch. Hoping no delays this time! If you put them in the same box you can keep the extra shipping fee.
|
|
|
Marto please answer to my friend ^^ @Marto74 (1) I would like to ask for a refund for my order that is more than 2 months old now. Order reference: UICAWGFJD OR I would like to get a HEX8A1 card as a form of consolation (2) Why don't you react to messages sent to technobit.eu? Best regards, W
|
|
|
Sajna nem kell a kutyanak se mar kozel 2 honap kesessel. Arrol nem is beszelve hogy kell egy nagyon eros tap(vagy tobb kicsi) hogy megtudd hajtani, meg egy tplink vagy rpi hogy hasheljen is. hex16a2 vel rengeteg gondom van, egyfolytaba aramtalanitanom kell, mert egyszeruen lecsokken a sebessege _0_ ra ! Most vettem az rpihez egy rele kapcsolot, csak az a masik bajom, hogy a boardok USB-n at aramot adnak egymasnak (Fingom sincs miert, teljesen egy balfasz tervezes lehetett? hisz 5v nem kell neki..) S igy szegeny RPInek kene elvinnie az egesz USB hubot es a boardokat mikor aramtalanitok.. szegenyke pislakol csak:D Elkell vagnom mind a 6 kabelon a testet es az 5 voltot.. szep kis melo lesz.. Szerintem jó áron el tudod adni Egyébként üdv mindenki, remélem nem gond ha idézek majd egy pár Petőfi költeményt az elkövetkezendő napokban, hogy kitörjek a bezártságból, és használhassam a fórumokat..
|
|
|
I have 6 hexC too, this can work together? So when i understand correct, i should use this for cgminer.conf: "hexminer8-voltage" : "955, "hexminer8-options" : "8:240", I use this too: "set_default_to_c" : true, That would work with this? Thanks. A few question for Loshia and Marto: #1 Its possible to ship it out on 10. feb? #2 Can you say me a configuration for cgminer? Is there something like this: --hexminer8-options x,x,x ?
Thanks!
First question is for marto about second one: --hexminer8-set-diff-to-one 1 --hexminer8-chip-mask 255 --hexminer8-voltage 955 --hexminer8-options 8:240 One by one --hexminer8-set-diff-to-one 1/0 the diff when set to 1 like mine - am testing it now brings a lot pressure between UB-HOST and PIC/ASIC communication Coin crafts can filter their response based on difficulty configured. When you set to one you got all nonces match diff 1 which has to be filtered and not send to the pool amusing you mine at diff greater than one. The only real advantage setting it to one is the cgminer 5 secs stats not moving up/down like crazy and average stats are settling down more quickly. Assume that you mine at diff 128. Cgminer sets it individually for each work passed to asic so it stays in sync with your pool always. Even if it is 1! When you set it to zero - ASIC send to the pic only nonces matching the diff 128 and back to host so you have about 128 times less data transfer, and cgminer shorts the time for submitting the nonce not checking against pool diff if it is a HW and all nasty stuff inside. the only disadvantage is that each nonce is counted not as one like before but as work difficulty itself which causes the stats variation. I suggest to use --hexminer8-set-diff-to-one 0 and configure your worker to mine at some constant higher difficulty. for instance when btcguild changes difficulty some old work may become stale oldddiff even though it is valid. In general if you happen to be in between two pools difficulties and your pool changing it up and down frequently you can have higher pool reject ratio - not good --hexminer8-chip-mask 255 - this was for development you can enable/disable chips based on binary mask bin 11111111 - 255 dec all chips enabled. Obviously zero is not a good choice here --hexminer8-voltage 955 the core voltage in milivolts. Do not go above one volt 1000 or do it on your risk --hexminer8-options 8:240 8 is chip count - used for some internal usb timing calculations , 240 is the frequency. The actual chip frequency is multiplied by four so 240 means 880 actually. the maximum value as far as know is 275. But try to stay below 260 in general And finally use --quiet when you have seen enough of course
|
|
|
A few question for Loshia and Marto: #1 Its possible to ship it out on 10. feb? #2 Can you say me a configuration for cgminer? Is there something like this: --hexminer8-options x,x,x ?
Thanks!
|
|
|
I got a tracking number. It was 3day from bulgari to hungary shipping. The tracking number can you see on the website in order details. I have a question for the users who have already gotten their products: how long does it take until you got your trackingcode for DPD-website. Once the status has changed to Shipped?
Never got a tracking code, got an e-mail, but the tracking bit was blank. My items shipped from Bulgaria to UK in about 5-7 days after the order system went from "payment accepted" to "shipped".
|
|
|
mudge! [Enabled] => N Ur device is disabled, dont know why. Try enable it.
|
|
|
Oh sorry, then i target Loshia with this:D I have brought a newer USB wifi for the RPI, i have replaced a nano usb wifi with a Tplink: http://www.tp-link.us/products/details/?categoryid=240&model=TL-WN822N . I had to install new driver for that and now works all great. I have many problem with the nano wifi, i think its soon broke. That hub was recommend by loshia , he already test it. I don't own that one. My hub using FE1.1S & cause so many problem
|
|
|
can I HEXMINER 2 or 3 start times and different pool register?
Use BALANCE pool option for cgminer.
|
|
|
Great news! Please, give me answer: Is there anything changed for Hex16A2? Duplicates? Chip0 bug?
|
|
|
Same error here but one from six board. Helps only when i shut down the psu. Other five board work well with 20gh. Hi,
my HEX16A2, which was delivered on thursday, went down from about 20HG/s to 5HG/s last night. It did that for the third time. I have a powered USB HUB and a 600W power supply, that is only for this miner. Restart of cgminer does not help, when i turn off the 12v and then turn it on again, the miner goes back to normal work. Is there a command to reset the miner hardware?
Bye Michael
|
|
|
I have used this "new" patch, and the bug is still available, the chip 0 dont send jobs:( Hello guys, Saw the error you were describing and it seems that I get an identical behavior. It seems that my Hex16A2 miner slowly degrades at a point where it doesn't hash at all. Did try to restart the process only but didn't manage to do anything. Today I did shutdown all miners (3 Hex16A + 1 Hex16A2) after I got an email from btc-guild that my miners where off. Turned them back on and everything started ok but got many duplicate errors (only from my Hex16A2 miner) and also noticed that the speed is degrading again. BTW I'm using cgminer 3.8.5 on a linux mint laptop. Should I manually apply this: Guy's, I found a bug for hex16A2 boards loosing woork of chip 0 - 87f0213112a3c69e2c55160b9c674b9de2cde996_u_1d.patch
while waiting for fix you can change
driver-hexminerc.c line 363 if (libhexc_cachenonce(&array_nonce_cache[0], nonce) && libhexc_cachenonce(&array_nonce_cache[lastchippos], nonce)) { to if ( libhexc_cachenonce(&array_nonce_cache[lastchippos], nonce)) {
This will bring back some dupes but will increase the performance with 1/16 Best, Twisted
|
|
|
Website is under maintenance. What is the price?
|
|
|
Was my faulty, i have selected a other tag on the git site. Now works perfect.
|
|
|
|