|
i am a php & ajax programmer and first time i saw Kano when i still a beginner on bitcoins i closed it after a minute and said ( What is this shit )
after i understood the different between PPLNS & PPS i tested more than 5 pools with Kano then i am here now
Kano not a site for the beginner so its difficult to gain more people
|
|
|
|
|
Kano need a powerfull interface design like BTC.com pool ant it will get more users every day
|
|
|
|
|
can i buy heatsink and use it with this Arctic Silver on S9 550 Chips which not have heatsink on it to be like 600 batches?
|
|
|
|
Transaction fees are included in the miner reward. thanks  |
|
|
|
|
did Kano take TX fees or divided it between miners or send it to who's find the block
|
|
|
|
  antpool get 0.0012% BTCpool get more than 0.003% |
|
|
|
|
i have 2 S9 powered by 2 APW5 on 220V
one of them start to get XXXX on all ASIC status after less than hour from restarting
so i powered 2 boards only for 5 days now without a problem
i can't send it to warranty because it will cost me a lot of money
|
|
|
|
|
i get HW errors with Kano on one S9 (0.0001%) and another (0.0005%)
i tried BTC.com and get a huge HW errors (0.0023%) and (0.0031%)
Chinese and USA ports tested
Kano get the lower HW errors i have ever seen
|
|
|
|
the machine is running for 10-15 minutes sometime 30-40 minutes with perfect hashrate and perfect temp and then suddenly it stops and starts within second and then the machine is not able to mine it is running miner fan is running at faster speed then slower speed again the same and not mining
this happen to me before and i found the reason is internet cable after more than 2 hours of restart and try happen again after a month from that and found the reason is my sister using torrent to download something and get all internet speed to her check your internet and try another pool too |
|
|
|
Fortunately for me, I've had a very solid last 6 weeks. No real problems, I don't turn them off unless absolutely necessary. Just let them run and don't mess with them seems to work great.
so we need to celebrate when something should happen is happen |
|
|
|
In 2 weeks of mining in a 70F warehouse I have now lost 3 boards out of 6 in the 2 S9's that I just got 2 weeks ago.
Is this normal?
I have bought over 150 S7's, 250 S5's and 300 S3's and never had this kind of failure rate.
Is anyone else experiencing this?
that's why they don't have S9 on hashnest until now |
|
|
|
|
they removed this heatsinks to make it heater and cannot overclock on the future
so they have more temp than B600 all the time
cgminer display maximum chip temp on the panel and they removed many of it to make PCB temp get high too
so you can't overclock it
|
|
|
|
|
this heatsinks existing on my B600 boards and not existing on my B550 boards
|
|
|
|
|
bitmain remove about 8 from this small pieces used to dissipate Chip temperature ( i don't know it's name )
on S9/550 to make it higher temp than S9/600 and sell it on different batch
that what i saw when i opened my B12 today
|
|
|
|
today one of my 2 antminer s9 B12 get dead board with XXX status after restart it work for 15 minutes and stop again any idea ??  You can swap the psu's for each machine. then check and see if the problem follows the psu if the problem follows the psu it is a psu issue. So swap psus and get back to us if the same board fails or not . i moved the board to another machine and it failed also after 30 minutes i sent it to them, it's second board dead from 3 S9 that mean 20% damages |
|
|
|
today one of my 2 antminer s9 B12 get dead board with XXX status after restart it work for 15 minutes and stop again any idea ??  |
|
|
|
|
my 3 S9 get dead on pool status
i traveled to antpool until it fixed
|
|
|
|
one of my both B12 get all 3 ASIC's XXX and reboot solve it why this happen ? my temp less than 82 all the time and freq lowered to 500  |
|
|
|
|
i powered 2 boards on each miner using 18AWG cable until i get the new one
it can handle 850W easily
|
|
|
|
|
Show Posts
