Ho risolto con il reindex! Ci ha impiegato circa 5 ore e mezza per ultimarlo... ora è tutto ok. Grazie a tutti
|
|
|
Cancella il file "peers.dat" e fai ripartire il client Niente, nemmeno così ho risolto Ho aperto il file di log dalla finestra di debug e ho notato messaggi poco rassicuranti come ad esempio: "ERROR: ProcessBlock() : already have block 295862" "CheckForkWarningConditions: Warning: Large valid fork found forking the chain at height 295862 lasting to height 295870 Chain state database corruption likely" Che significa e soprattutto perché il client non mi dice che ci sono problemi? Da quanto ho letto cercando su Google non si risolve nemmeno riscaricando la blockchain... ma pare essere un problema di client/ubuntu... può essere?
|
|
|
Nell'angolino in basso a destra, le barre tipo il segnale dei cellulari, ti dicono con quanti peer è connesso, se ci sono delle barre gialle/arancioni va bene, se cè anche l'ultima barra verde ottimo, se c'è solo la rossa, male. Inoltre se rimani fermo un po' con il mouse sulle barre ti appare il popup con il numero di peer connessi, cosa dice ?
Problemi di firewall ? Magari il provider filtra le porte associate a Bitcoin ? Ecco l'output: Effettivamente oltre 295862 non va... Firewall non ne uso e non penso sia un problema di provider... finora ha sempre funzionato. L'unico cambiamento che ho fatto è qualche aggiornamento di Ubuntu ma non capisco cosa possa essere stato inibito...
|
|
|
Salve, ho riaperto Bitcoin-QT dopo una decina di giorni e mi ha chiesto di effettuare l'upgrade alla versione 0.9.1. L'ho effettuato e ho lasciato aperto il client per fargli terminare la sincronizzazione con la blockchain: 9 giorni rimanenti. In mezza giornata è arrivato a 7 giorni e poi ho spento il pc. Il giorno successivo invece è rimasto sempre su 7 giorni mancanti, nonostante io abbia lasciato il pc acceso tutto il giorno! Addirittura oggi dice 8 giorni mancanti. E' come se non andasse avanti con la sincronizzazione. Ho controllato lo spazio libero sul disco e ci sono circa 60 GB.
Quale può essere il problema?
Utilizzo Ubuntu 14.04.
|
|
|
Hello, what is the recommended frequency i can set for cgminer? I'm currently using 650... what is the maximum and what is the recommended?
Moreover, what is it "chips=5"?
|
|
|
Long time i didn't buy here. I see that the shop is changed and my account seems not to exist anymore. Have i to register again?
|
|
|
Hello, how to use "Pools" button in the web panel?
the pools button swaps between the first pool and second pool you have specified. unless you are using a cloud proxy, your pool address will be your own network proxy in both instances. clicking pools, will switch from 1st pool to 2nd pool. Since i'm connetting to my stratum proxy server, how to configure it to use two differente pools?
|
|
|
Hello, how to use "Pools" button in the web panel?
|
|
|
Prova con due alimentatori.
|
|
|
Hello, my Cube is just arrived, but it seems to have some problems As i power on it the power consuption quickly reach about 260W... is this normal? After about 1 minute: - it starts to make a strange noise (it seems to be the fan that make the noise) - the power consumption slows down till up 25W - the web panel became unreachable What could be the problem? Could be the fan? If i am right, is this the safe mode of Cube to power off in case of fan failure? Thank you and sorry for my english. I solved using 2 power supply! So what could be that noise?
|
|
|
Hello, my Cube is just arrived, but it seems to have some problems As i power on it the power consuption quickly reach about 260W... is this normal? After about 1 minute: - it starts to make a strange noise (it seems to be the fan that make the noise) - the power consumption slows down till up 25W - the web panel became unreachable What could be the problem? Could be the fan? If i am right, is this the safe mode of Cube to power off in case of fan failure? Thank you and sorry for my english.
|
|
|
Do you know what the command node do?
|
|
|
That’s all folks. If you have any problems let me know. I will do my best to help. Where are you?
|
|
|
I solved all my problems using absolute paths, even in miningserver.sh file. Anyway i had to remove node command, otherwise stratum proxy doesn't start.
What the node command do? Besides it was not included with Raspian and i had to install it.
|
|
|
I solved using Raspian, instead of Occidentalis. I have just a problem if i want to run the mining comand at the startup. I added the code to /etc/rc.local, but at every boot i get this error: /etc/rc.local: 20: cd: can't cd to mining-stratum-proxy [FAIL] startpar: service(s) returned failure: rc.local ... failed! How to fix it?
|
|
|
I tried to use Fedora ARM Installer on Windows 7 and on Ubuntu but in both cases it can't find the SD. No device appears in the menu. So i used dd command under Ubuntu and i obtained the SD with 2 partition, but when i switch on raspberry with the SD inside it doesn't work. It just doesn't run. What could be the problem?
|
|
|
out of stock again...
Will you sell again them?
|
|
|
Hello, will this price be lowered?
1 Cube = 3 Blades
2 months ago the price for 1 Blade was about 270€. So now you are selling a Cube at the same price of 3 Blades with price of 2 months ago!
Any other here agree with me?
|
|
|
|