|
Hi Guys,
Do we have any mining profitability calculator?
now I'm running 24core @ 27Kh/s each ? any idea how much MAC/month
Cheers
|
|
|
|
|
Hey,
already did a ticket, in fact isn't the real problem, because 2000confirmation huge but okay...
but look like i'm stuck @1680confirmation since this morning ( 10hours)
will let you know the feedback from cryptopia
|
|
|
|
|
question guys,
why 2000 confirmation needed on Cryptopia???
|
|
|
|
|
Hi Guys,
My MN working for several day, I would like to know how much XCXT I "should get" by day?
I'm on something like 0.5-2XCXT by day.
thanks
|
|
|
|
|
HOw to get the 20 SUB1x to start a MN?
|
|
|
|
|
Does someone want some coin? got enough to start a MN
|
|
|
|
|
so since coinsmarket is down, no more exchange right?
|
|
|
|
Hi Guys,
Just setup a MN, look like working but how I can't check if everything is OK?
Thanks
type this command: SkeletonRevive masternode status If the line "notCapableReason" is empty like this: "notCapableReason" : "" You should be Okay and see your balance increase in couple hours  Thanks, it's look exactly like this ^^, will update you tomorrow |
|
|
|
|
got question on MN,
when I check status I got this:
13669df6e4139c4bed9859cded177f59ddd42f0bc5d4ce3ddbf96532dc74210a-1": " ENABLED 70206 AM1RP8nEGZv6KMoxJ3DH1m78j2faLsNkyJ 1514990413 76648 0 0 92.167.32.110:7209",
not sure it's good to have the 2 last value at 0 ?
|
|
|
|
ok I found my problem after debug.log check in fact wallet still check on 33220 on internal network.... so into firewall need to do external port 50001 to 33220 internal now the value is increasing  |
|
|
|
When i list masternode list full
I got one value stay at 0, it's the masternode rating, it stay at 0 for hours now...
"eff9c31601fxxxxxxxxxxxxxxxxxxxxxxxce4fb7d4ffb3f58dd-0" : " ENABLED 60026 SffzvuqWxxxxxxxxxxxxxxxZ2HkpfXRbq 92.167.32.110:50001 1514987975 0 1514988058",
je port is closed ! open port finder Remote Address 92.167.32.110 Use Current IP Port Number 50001 Check Closed Port 50001 is closed on 92.167.32.110. thanks but I double check and port is open in my router & firewall it mark at close like nothing is "answering" on this port. deos the skeletonrevive.conf should have something? |
|
|
|
|
When i list masternode list full
I got one value stay at 0, it's the masternode rating, it stay at 0 for hours now...
"eff9c31601fxxxxxxxxxxxxxxxxxxxxxxxce4fb7d4ffb3f58dd-0" : " ENABLED 60026 SffzvuqWxxxxxxxxxxxxxxxZ2HkpfXRbq 92.167.32.110:50001 1514987975 0 1514988058",
|
|
|
|
|
Hi Guys,
Just setup a MN, look like working but how I can't check if everything is OK?
Thanks
|
|
|
|
|
Hello Guys,
Still sync wallet since yesterday....
Now I'm on the 29Dec17 Beta 2 it the best version to stay or a new release is available?
or maybe the blockchain is available to download?
Thanks
|
|
|
|
oh crap my antminer goes to ultra high fan speed every hour just after ending dev fee , pls someone how to avoid this? , and i noticed that the prority is 1 on devfee so if the pool goes down i loose mining? , have someone the original firmware??
you can find original firmware here https://shop.bitmain.com/support.htm?pid=00720170915192851224mJ36J1ap066EI also think to rollback, i'm not sat about the dev fee, honnestly I would prefer to pay few bucks to have the firmware without this |
|
|
|
Flash OK... look fine at the moment what is the 'default asic voltage' Value? good to hear. I don't know what the default value is to be honest as I modified my hardware and don't know the hardware defaults. That's why I need your guys feedback about wattages I mean in your modified interface you have the option asic voltage with range 200-460, was is the default value, to know where to start and decrease it |
|
|
|
Flash OK... look fine at the moment what is the 'default asic voltage' Value? |
|
|
|
First milestone is reached: the first flashable firmware image is a fact.  Please give a reply in this thread if you're willing to test it. It's really experimental so here are the terms:- I am not responsible for any damage to your miner, flash at your own risk - You're not in panic when you see HW errors because of the low voltage - You do have a watt meter - You're willing to test and give me feedback for improvement. - You're not going to complain about the 1.5% mining fee. what you will get:- no more high speed fan's during startup - no more low fan warnings (the fan speed is fully unlocked) - a first version of the unlocked voltage. If you do join this beta test, please test the following:set the speed to 400Mhz on your bitmain firmware and measure the amount of watts needed. flash the beta firmware and set fan speed to manual at 20% set the speed to 400Mhz and try to get as low as you can on the voltage settings before you see hardware errors. PM me then the following information:- your batch - the wattage at 400mhz on the bitmain firmware - the lowest possible voltage setting for 400mhz on the custom firmware - the wattage at the new voltage - your fan RPM speed at 20% ofcourse if you run in any other problems please PM me as well. Of course I agree with all your condition, I'm ready to test thanks man! |
|
|
|
Maybe easier to share just the modified file?
we can then push with a winscp..
This is how I ran it at first, but as the linux rootfs is loaded into RAM, the modded files are gone after a reboot... Therefore I tried to modify / rebuild the u-boot ramdisk image with the modded files included, but something went wrong I imagine you also try to take the latest firmware on bitmain site, and just add your file into it? |
|
|
|
|
Maybe easier to share just the modified file?
we can then push with a winscp..
|
|
|
|
|
Show Posts
