Just config 2 miner (or and reconf) to mine 1 coin on same pool to different wallets. After 24 hours compare the income indicators.
good idea i'll try it later
|
|
|
I believe there is no pool paying according heat radiated from miners, so what is pool saying about hashrate?
:-D ^
I think pool show good information from baikal sgminer. but its hard to tell if I really got an gain in reward since reward itself move so much day to day.
some point out that sgminer and pool tiself might show correct value but physically its not overclock at all it seems
physic and science tell rise in clock result of gain in caloric heat that I don't have actually. 20% rise should definitively be visible.
So at this point overclocking on giant B is false imo
Don`t think so much about wattage and temp, the fact is that if you`re seeing higher hashrate on pool side, then your Giant B is overclocked! what if poolside take good information from sgminer baikal ? share rate move alot intra day or day to day due to nicehash miner movement and luck. I find it wrong that 20% gain in clock cannot result of any increase in heat,strongly suggest that overclock didn't apply physically but only on software part
|
|
|
^
I think pool show good information from baikal sgminer. but its hard to tell if I really got an gain in reward since reward itself move so much day to day.
some point out that sgminer and pool tiself might show correct value but physically its not overclock at all it seems
physic and science tell rise in clock result of gain in caloric heat that I don't have actually. 20% rise should definitively be visible.
So at this point overclocking on giant B is false imo
|
|
|
utility falls to 5.5 too,with temperature same I don't think there's any overclocking really apply on it.
Whats if baikal just told us truth and its really not possible overclock those miner ?
Can't believe 20% rise to clock can't get up the temperature even 1% greater,they are literally same.impossible any overclockk have apply,physic say it must be hotter lol.
|
|
|
There are some changes needed in sgminer code in order to allow for changing frequency, so for now its preset to 480 mhz, which gives a slight OC.
hello, temperature still suggest that overclock didn't apply now utility is around 5.2 to 5.7 for (3) flashed machine vs (+10) 5.5 look like it might stabilize more with time. supernova suck at verifying stats,this site is bad as 2014 lol
|
|
|
I flash 2 machine I'll try to compare Utility work over 12-24h see if there's difference with my other non-flash baikal
after 2-3 hours at least WU is around 6 while my other miner are more 5.5-5.6. For now share seems more consistent after flashing,will see later.
|
|
|
''cd sgminer-baikal''
Where do I find this folder ? Can't found the path
thanks alot
As xxALEXANDRxx says, follow the instructions. Sure, BFGMiner will work, but you will need to create a new set of USB drivers/library to communicate with baikal asic. Obviosly - BFGMiner will not be an easy way. "cd sgminer-baikal" means that you will open folder named "sgminer-baikal", which is there as long as you have cloned git repository sucessfully. Just a tip: If you`re not sure of what you are doing, i suggest that you do a little research before you mess up your machine, and don`t know how to get it back :-) Alright so everything when well. except one thing,it show 480mhz when I put 415 mhz,did you know why? I've read entire thread again and I see 1-2 ppl asking for same thing and nobody seems able to answer to their question about this exact situation.it is predetermined overclock or something else ? it seems strange to me,temperature is the same with +80mhz thanks
|
|
|
''cd sgminer-baikal''
Where do I find this folder ? Can't found the path
thanks alot
|
|
|
Do we think Giant N will eventually get new CN algos?
No. If they did - Baikal would never have their 5 for 1 offer. did your github oc image still work for BKB ? I try installing BFGminer as someone pointed out it might work so I take the easiest way but all update or installing become a fail process ''Killedg package lists... 99%/20%'' So I wonder if baikal setup some auto delete stuff or thing like that,im worried even your image might not work for me. just want to know before start trying if its something 'serious' or not( I see possible hardware issue on some forum) thanks There is no auto-deletion. About the error look at README.md for compilation errors. BFGminer need correct driver for your baikal device, otherwise it will not work. Wow thanks for fast answer ! I will try this asap !
|
|
|
Do we think Giant N will eventually get new CN algos?
No. If they did - Baikal would never have their 5 for 1 offer. did your github oc image still work for BKB ? I try installing BFGminer as someone pointed out it might work so I take the easiest way but all update or installing become a fail process ''Killedg package lists... 99%/20%'' So I wonder if baikal setup some auto delete stuff or thing like that,im worried even your image might not work for me. just want to know before start trying if its something 'serious' or not( I see possible hardware issue on some forum) thanks
|
|
|
Temperature input would relate to suitable ambient temperate , room temperature prior to active operation. You'd be pretty uncomfortable standing in a room below zero or above 40c. So operating it in sub zero conditions could be a problem by that advice I think, its possible it would lead to condensation and cause further problems. Especially cold air can carry excess moisture into what is basically a kind of space heater with fine electronics also. If your device is indicating operating at 45c thats fine, the actual input temperature must be far lower. I cant think of any chips recently upset by such a low operating onboard temp
thanks buddy for input I tried my ass to keep those machine under 40 but it seems impossible when you scale this up lol what do you consider as a bad temps ? It seems when the air temperature gets above 97 Fahrenheit my miners will reach 56 Celsius and start to go into flashing mode (no production). This is what I have found. Acceptable air temp in = 32 - 95 degrees Fahrenheit Chip temp should be below 55 Celsius. thanks alot for information ! btw I dont think we gonna ROI our mining equipment lol... All those coin network keep growing insanely while price keep diving,make no sense. mining gold rush is done now seem
|
|
|
This token causes only one desire, never to buy it and similar tokens, one of my most unprofitable transactions is LBRY
funny, one of my most profitable transaction was lbry.
|
|
|
who know maybe sia will hit 1$ one day,remember when people was saying XRP or XEm was impossible to reach a dollars cause big supply? ahah... look like its maybe good time to get in stack a milion share and lets sleep on that ![Grin](https://bitcointalk.org/Smileys/default/grin.gif)
|
|
|
Is Baikal B headed to doorstopper category? I'm just wondering if Baikal could update algos, or if the market could ever shift the earnings into a positive direction. Right now if makes much more sense to buy GPUs as they occasionally earn more for the dollar, even @ the new discounted price of $1000 + shipping.
Baikal are good to their customer and its time to prove it. I and all miners think Baikal should make customers happy by announcing new algos updates for Giant B. This way they can sell new unit as well and keep existing customers on board so they buy more units from them in future in addition to the positive marketing and image. More costumization would be very appreciate,like overclocking
|
|
|
So overclocking really work at this moment on Giant B ?
|
|
|
well I think community have to do his job too to keep it more alive, we have result from dev,but its time to be more active now
|
|
|
Temperature input would relate to suitable ambient temperate , room temperature prior to active operation. You'd be pretty uncomfortable standing in a room below zero or above 40c. So operating it in sub zero conditions could be a problem by that advice I think, its possible it would lead to condensation and cause further problems. Especially cold air can carry excess moisture into what is basically a kind of space heater with fine electronics also. If your device is indicating operating at 45c thats fine, the actual input temperature must be far lower. I cant think of any chips recently upset by such a low operating onboard temp
thanks buddy for input I tried my ass to keep those machine under 40 but it seems impossible when you scale this up lol what do you consider as a bad temps ?
|
|
|
Hello im interested into temperature input for BKB on website it say 0-40,this is chips fonctionnality or ambian temp ? Mine going around 40-45 so im not sure if its good,substainable or bad.
Thanks alot
|
|
|
|