Is there some more support documentation out there on how to set these things up? I'd like to know a little bit more about how the controller interfaces with the Pi. I'd prefer to start with a stock Rasbian Wheezy image. I've got cgminer 4.3.3 building now, but I'm assuming some kind of configuration is required for the Pi to communicate with the controller.
Thanks!
Chad
BlackArrow Bitfury devices need the --enable-bab option when compiling cgminer. just include this when compiling and the boards and chips will be detected on startup of cgminer. |
|
|
|
|
i can offer you 0.2 posted to eu
|
|
|
|
thanks i will check it out my power connections.
seems a dodgy board has killed my controller. im wondering if you have power plugged into your 4x controller or if its just powered by the pi? previously i only had power plugged into the controller and this was also powering the pi, maybe that also contributed.
Try pulling one of your barrel connectors directly into the controller board; the controller should be supplying power to the pi via the 26 pin ribbon cable. ok thanks, thats how it was setup until i connected a bad board and fried it. waiting on a replacement board to get hashing again  |
|
|
|
are you powering the controller with a barrel lead or something else or does it get power from the pi?
I'm currently using PCI-E to 3 barrel connectors for all my power needs at the moment one word of caution and the reason for why I am replacing my cables; one of the pairs for the PCI-E to barrel connectors frayed every so slightly and caused a brief short. Not sure how it occurred but I've order screw connectors for all of my units and intend to replace all the power connectors (better safer than sorry). I recommend giving your PCI-E connectors a once over to make sure none of the power (red) or ground (black) are frayed and if they are you should at the very least isolate the damaged cables with small stripe of electrical tape or re solder / re-shrink wrap the cable. thanks i will check it out my power connections. seems a dodgy board has killed my controller. im wondering if you have power plugged into your 4x controller or if its just powered by the pi? previously i only had power plugged into the controller and this was also powering the pi, maybe that also contributed. |
|
|
|
any one else getting a lot of duplicate shares? pool reports around 33k for 750gh, is this normal for these boards?
I'm seeing some high dupe as well. going to take a look at how cgminer performs once I tweak it. please share your settings, i am using 4.3.3 on default which is supposed to auto tune but saw no improvement over 24 hours. |
|
|
|
|
are you powering the controller with a barrel lead or something else or does it get power from the pi?
|
|
|
|
|
are you also selling them in airtites?
|
|
|
|
Stone is taxed now, worth at least 719,20$
Willing to sell for less
taxed meaning valued? What else could it mean? so then can we see the valuation? |
|
|
|
Stone is taxed now, worth at least 719,20$
Willing to sell for less
taxed meaning valued? |
|
|
|
|
any one else getting a lot of duplicate shares? pool reports around 33k for 750gh, is this normal for these boards?
|
|
|
|
our A2 based scrypt miner  looks good, will there be a new tp link bin to support this? |
|
|
|
can someone post the pi image they are using for this? tried the black arrow one but reports error with mining_proxy and still doesnt work after updating it.
I made a support thread / setup guide for the black arrow bitfury 16 chip board. I'll post my cgminer setup guide later. Here's the thread: https://bitcointalk.org/index.php?topic=615118. thanks, looks like it was more my wiring than software. |
|
|
|
|
my boards are running, happy to help anyone having problems.
|
|
|
|
I get that too. Very little documentation on that.  would be very interested if you can solve it, otherwise will have to try again with chainminer.... |
|
|
|
|
running cgminer 4.3.3 and compiling with --enable-bab i get BaB0: Delay getting work reply ...
chips are detected at startup and connected to pool, can any cgminer users help?
|
|
|
|
can someone post the pi image they are using for this? tried the black arrow one but reports error with mining_proxy and still doesnt work after updating it.
You can use any pi image with the newest version of CGMiner, kano added code for these a while back. any idea on configs? running cgminer latest version i get BaB0: Delay getting work reply... |
|
|
|
|
can someone post the pi image they are using for this? tried the black arrow one but reports error with mining_proxy and still doesnt work after updating it.
|
|
|
|
We successfully tested Live Baseball, Cricket and more and finish last tasks to release it during the week.  play tennis missed . tennis matches will be opened when ?
These in play side markets come back tomorrow. when will dividend be paid?
Friday, because on this day the last big open bet slip will be decided which was sent End of last month. assume friday was missed? Any answer to this? payment made, thanks |
|
|
|
|
Show Posts
