|
ok, I just re-read your post above, so your saying your pulling 60 Watt at the wall, and getting 80% efficiency at the power brick? 60Watt -> 48watt (225Mhz)?
|
|
|
|
Wow 60 Watts? what frequency are you running at? According to SideHack's power chart, 60 watts is 275MHz 100MHz (44GH) 660mV/node 2.64V total; 12V 1.4A for 16.8W/0.38J/GH
125MHz (55GH) 660mV/node 2.64V total; 12V 1.7A for 20.4W/0.37J/GH
150MHz (66GH) 660mV/node 2.64V total; 12V 2.0A for 24.0W/0.36J/GH
175MHz (77GH) 693mV/node 2.77V total; 12V 2.5A for 30.0W/0.39J/GH
200MHz (88GH) 715mV/node 2.86V total; 12V 3.1A for 37.2W/0.42J/GH
225MHz (99GH) 755mV/node 3.02V total; 12V 3.8A for 45.6W/0.46J/GH
250MHz (110GH) 770mV/node 3.08V total; 12V 4.4A for 52.8W/0.48J/GH
275MHz (121GH) 770mV/node 3.08V total; 12V 4.9A for 58.8W/0.49J/GH Ill pick up a P3 Killawatt on my way home from work tonight and see what I'm pulling per pod. But even so, then just jump to a 750Watt, its still the same common slot power supply, still under $40 https://www.amazon.com/HP-599383-001-Common-Platinum-Supply/dp/B00719064I/I've used the 1200Watt and Sidehacks break out board for GPU builds and AntMiners, its a solid reliable design. (those are just crazy expensive right now) |
|
|
|
|
I get a solid 225 out of the ones I've tested, they heat up quick but the fans kick in hard and the bottom of the Terminus only hits around 65C (infrared thermometer). Its stable and the Hashrate actually fluctuates between around 77Gh and 140Gh (averages 96)
"0: GSE 10030054: BM1384:8 225.00MHz (1/19/43/0) | 110.2G / 96.41Gh/s"
I run from a 6A powerbrick. From a stack of China made test units, its the most reliable Ive used so far. It gets a little hot so I know its not that efficient.
I have that and a 5A that is reliable to, not sure what the exact pull is, I dont have a clamp meter and im too lazy to buy a KillaWatt.
the 6A is a "LX1206" made in china and the 5A is a "HTY-1205000"
|
|
|
|
Are you sure the reset line stays pulled high? If the controller sees a problem it pulls reset low for one second, then high for two seconds, then rechecks, so if the problem persists the reset line cycles low and back to high every 3 seconds.
yes, I let it sit for a while, it has a VERY minor fluctuation 1.409 to 1.410 volts but it never drops. while writing this, it just kicked off a single cycle of work then failed again. [2018-03-03 13:00:31.406] GSE 402: Terminus BM1384 Bitcoin Miner (10030050)
[2018-03-03 13:00:31.408] GSE 402 TX: 84:00:00:11
[2018-03-03 13:00:31.411] GSE 402 TX: 84:00:00:11
[2018-03-03 13:00:31.612] GSE 402: found 0 chip(s)
[2018-03-03 13:00:31.612] Hotplug: GekkoScience added GSE 402
[2018-03-03 13:00:31.613] GSE 402 failure, disabling!
[2018-03-03 13:00:31.613] GSE 402: setting frequency to 100.00MHz
[2018-03-03 13:00:31.615] GSE 402 TX: 82:07:83:1C
[2018-03-03 13:00:31.617] GSE 402 TX: 84:00:04:00
[2018-03-03 13:00:35.705] Testing pool stratum+tcp://pool.ckpool.org:3333
[2018-03-03 13:00:36.981] GSE 403: Terminus BM1384 Bitcoin Miner (10030050)
[2018-03-03 13:00:36.982] GSE 403 TX: 84:00:00:11
[2018-03-03 13:00:36.984] GSE 403 TX: 84:00:00:11
[2018-03-03 13:00:37.186] GSE 403: found 0 chip(s)
[2018-03-03 13:00:37.186] Hotplug: GekkoScience added GSE 403
[2018-03-03 13:00:37.186] GSE 403 failure, disabling!
[2018-03-03 13:00:37.186] GSE 403: setting frequency to 100.00MHz
[2018-03-03 13:00:37.188] GSE 403 TX: 82:07:83:1C
[2018-03-03 13:00:37.190] GSE 403 TX: 84:00:04:00
[2018-03-03 13:00:40.706] Testing pool stratum+tcp://pool.ckpool.org:3333
[2018-03-03 13:00:42.649] GSE 404: Terminus BM1384 Bitcoin Miner (10030050)
[2018-03-03 13:00:42.650] GSE 404 TX: 84:00:00:11
[2018-03-03 13:00:42.652] GSE 404 TX: 84:00:00:11
[2018-03-03 13:00:42.861] Hotplug: GekkoScience added GSE 404
[2018-03-03 13:00:42.863] GSE 404 TX: 84:00:00:11
[2018-03-03 13:00:42.870] GSE 404 RX: 13:82:90:FF:0F
[2018-03-03 13:00:42.870] GSE 404 RX: 13:82:90:BF:12
[2018-03-03 13:00:42.870] GSE 404 RX: 13:82:90:FF:0F
[2018-03-03 13:00:42.870] GSE 404 RX: 13:82:90:FF:0F
[2018-03-03 13:00:42.870] GSE 404 RX: 13:82:90:FF:0F
[2018-03-03 13:00:42.870] GSE 404 RX: 13:82:90:FF:0F
[2018-03-03 13:00:42.870] GSE 404 RX: 13:82:90:FF:0F
[2018-03-03 13:00:42.870] GSE 404 RX: 13:82:90:FF:0F
[2018-03-03 13:00:42.972] GSE 404: found 8 chip(s)
[2018-03-03 13:00:43.088] GSE 404: setting frequency to 81.25MHz
[2018-03-03 13:00:43.090] GSE 404 TX: 82:06:03:18
[2018-03-03 13:00:43.092] GSE 404 TX: 84:00:04:00
[2018-03-03 13:00:43.093] GSE 404: sending chain inactive for 8 chip(s)
[2018-03-03 13:00:43.094] GSE 404 TX: 85:00:00:0F
[2018-03-03 13:00:43.096] GSE 404 TX: 01:00:00:19
[2018-03-03 13:00:43.098] GSE 404 TX: 01:20:00:01
[2018-03-03 13:00:43.098] GSE 404 RX: 80:0C:00:03:00
[2018-03-03 13:00:43.098] GSE 404: chip reported frequency of 81.25MHz
[2018-03-03 13:00:43.098] GSE 404 RX: 80:0C:00:03:00
[2018-03-03 13:00:43.098] GSE 404: chip reported frequency of 81.25MHz
[2018-03-03 13:00:43.098] GSE 404 RX: 80:0C:00:03:00
[2018-03-03 13:00:43.098] GSE 404: chip reported frequency of 81.25MHz
[2018-03-03 13:00:43.098] GSE 404 RX: 80:0C:00:03:00
[2018-03-03 13:00:43.098] GSE 404: chip reported frequency of 81.25MHz
[2018-03-03 13:00:43.098] GSE 404 RX: 80:0C:00:03:00
[2018-03-03 13:00:43.098] GSE 404: chip reported frequency of 81.25MHz
[2018-03-03 13:00:43.099] GSE 404 RX: 80:0C:00:03:00
[2018-03-03 13:00:43.099] GSE 404: chip reported frequency of 81.25MHz
[2018-03-03 13:00:43.099] GSE 404 RX: 80:0C:00:03:00
[2018-03-03 13:00:43.099] GSE 404: chip reported frequency of 81.25MHz
[2018-03-03 13:00:43.099] GSE 404 RX: 80:0C:00:03:00
[2018-03-03 13:00:43.099] GSE 404: chip reported frequency of 81.25MHz
[2018-03-03 13:00:43.100] GSE 404 TX: 01:40:00:0C
[2018-03-03 13:00:43.103] GSE 404 TX: 01:60:00:14
[2018-03-03 13:00:43.105] GSE 404 TX: 01:80:00:16
[2018-03-03 13:00:43.107] GSE 404 TX: 01:A0:00:0E
[2018-03-03 13:00:43.109] GSE 404 TX: 01:C0:00:03
[2018-03-03 13:00:43.111] GSE 404 TX: 01:E0:00:1B
[2018-03-03 13:00:43.112] GSE 404: open cores @ 81.25MHz
[2018-03-03 13:00:45.329] GSE 404: start work @ 81.25MHz
[2018-03-03 13:00:45.706] Testing pool stratum+tcp://pool.ckpool.org:3333
[2018-03-03 13:00:50.348] GSE 404 TX: 84:00:04:00
[2018-03-03 13:00:50.707] Testing pool stratum+tcp://pool.ckpool.org:3333
[2018-03-03 13:00:55.420] GSE 404 TX: 84:00:04:00
[2018-03-03 13:00:55.707] Testing pool stratum+tcp://pool.ckpool.org:3333
[2018-03-03 13:00:55.763] Work update message received
[2018-03-03 13:01:00.428] GSE 404 TX: 84:00:04:00
[2018-03-03 13:01:00.707] Testing pool stratum+tcp://pool.ckpool.org:3333
[2018-03-03 13:01:14.751] Testing pool stratum+tcp://pool.ckpool.org:3333
[2018-03-03 13:01:19.752] Testing pool stratum+tcp://pool.ckpool.org:3333
[2018-03-03 13:01:19.821] GSE 404 TX: 84:00:04:00 R:0 HW:0 WU:0.0/m
[2018-03-03 13:01:24.752] Testing pool stratum+tcp://pool.ckpool.org:3333
[2018-03-03 13:01:24.847] GSE 404 TX: 84:00:04:00
[2018-03-03 13:01:26.755] Work update message received
[2018-03-03 13:01:29.753] Testing pool stratum+tcp://pool.ckpool.org:3333
[2018-03-03 13:01:29.881] GSE 404 TX: 84:00:04:00 R:0 HW:0 WU:0.0/m
[2018-03-03 13:01:34.753] Testing pool stratum+tcp://pool.ckpool.org:3333
[2018-03-03 13:01:34.895] GSE 404 TX: 84:00:04:00
[2018-03-03 13:01:39.753] Testing pool stratum+tcp://pool.ckpool.org:3333
[2018-03-03 13:01:39.966] GSE 404 TX: 84:00:04:00 R:0 HW:0 WU:0.0/m
[2018-03-03 13:01:44.754] Testing pool stratum+tcp://pool.ckpool.org:3333
[2018-03-03 13:01:45.026] GSE 404 TX: 84:00:04:00
[2018-03-03 13:01:49.754] Testing pool stratum+tcp://pool.ckpool.org:3333
[2018-03-03 13:01:50.031] GSE 404 TX: 84:00:04:00 R:0 HW:0 WU:0.0/m
[2018-03-03 13:01:54.755] Testing pool stratum+tcp://pool.ckpool.org:3333
[2018-03-03 13:01:55.046] GSE 404 TX: 84:00:04:00
[2018-03-03 13:01:58.772] Work update message received
im going to build a quick jumper connector so i can watch the voltage for an extended period so i can catch it again when it starts responding(without having to hold the meter leads to the 2 pins by hand). |
|
|
|
just had a failure. interesting its not respecting the --gekko-start-freq 80 command. @Sidehack, I checked the reset header, its still showing 1.4v event though it says 0 chips. [2018-03-03 12:05:27.645] GSE 0: Terminus BM1384 Bitcoin Miner (10030050)
[2018-03-03 12:05:27.647] GSE 0 TX: 84:00:00:11
[2018-03-03 12:05:27.649] GSE 0 TX: 84:00:00:11
[2018-03-03 12:05:27.853] GSE 0: found 0 chip(s)
[2018-03-03 12:05:27.853] Probing for an alive pool
[2018-03-03 12:05:27.855] GSE 0 failure, disabling!
[2018-03-03 12:05:27.855] Testing pool stratum+tcp://pool.ckpool.org:3333
[2018-03-03 12:05:27.855] GSE 0: setting frequency to 100.00MHz
[2018-03-03 12:05:27.857] GSE 0 TX: 82:07:83:1C
[2018-03-03 12:05:27.859] GSE 0 TX: 84:00:04:00
[2018-03-03 12:05:27.993] Pool 0 difficulty changed to 4000
[2018-03-03 12:05:28.045] Pool 0 message: Authorised, welcome to ckpool.org 1DtRzACnDAr2SPXMyAp3pLMfREPch3PbhA!
[2018-03-03 12:05:28.045] Stratum authorisation success for pool 0
[2018-03-03 12:05:28.047] Pool 0 stratum+tcp://pool.ckpool.org:3333 alive
[2018-03-03 12:05:28.102] Pool 0 difficulty changed to 32
[2018-03-03 12:05:28.102] Network diff set to 3.01T
[2018-03-03 12:05:28.103] New block: 00000000000000000000e499bf7fa30e87a9d2542885276cb80fb2fdeab1ffdb... diff 3.01T
[2018-03-03 12:05:28.855] Testing pool stratum+tcp://pool.ckpool.org:3333
[2018-03-03 12:05:28.855] Work update message received
[2018-03-03 12:05:32.857] Work update message received
[2018-03-03 12:05:33.856] Testing pool stratum+tcp://pool.ckpool.org:3333
[2018-03-03 12:05:34.115] GSE 1: Terminus BM1384 Bitcoin Miner (10030050)
[2018-03-03 12:05:34.116] GSE 1 TX: 84:00:00:11
[2018-03-03 12:05:34.120] GSE 1 TX: 84:00:00:11
[2018-03-03 12:05:34.321] GSE 1: found 0 chip(s)
[2018-03-03 12:05:34.322] Hotplug: GekkoScience added GSE 1
[2018-03-03 12:05:34.323] GSE 1 failure, disabling!
[2018-03-03 12:05:34.323] GSE 1: setting frequency to 100.00MHz
[2018-03-03 12:05:34.325] GSE 1 TX: 82:07:83:1C
[2018-03-03 12:05:34.326] GSE 1 TX: 84:00:04:00
[2018-03-03 12:05:38.857] Testing pool stratum+tcp://pool.ckpool.org:3333
[2018-03-03 12:05:39.688] GSE 2: Terminus BM1384 Bitcoin Miner (10030050)
[2018-03-03 12:05:39.689] GSE 2 TX: 84:00:00:11
[2018-03-03 12:05:39.694] GSE 2 TX: 84:00:00:11
[2018-03-03 12:05:39.897] GSE 2: found 0 chip(s)
[2018-03-03 12:05:39.897] Hotplug: GekkoScience added GSE 2
[2018-03-03 12:05:39.900] GSE 2 failure, disabling!
[2018-03-03 12:05:39.900] GSE 2: setting frequency to 100.00MHz
[2018-03-03 12:05:39.901] GSE 2 TX: 82:07:83:1C
[2018-03-03 12:05:39.902] GSE 2 TX: 84:00:04:00
[2018-03-03 12:05:43.857] Testing pool stratum+tcp://pool.ckpool.org:3333
[2018-03-03 12:05:45.262] GSE 3: Terminus BM1384 Bitcoin Miner (10030050)
[2018-03-03 12:05:45.264] GSE 3 TX: 84:00:00:11
[2018-03-03 12:05:45.267] GSE 3 TX: 84:00:00:11
[2018-03-03 12:05:45.468] GSE 3: found 0 chip(s)
|
|
|
|
Hey VH, I saw some wierdness with one of my units yesterday during testing. It spun up great on the first try and was chugging along at 150Mhz. I closed and restarted cgminer and the damn thing just crapped out. It was weird because the only change was restarting cgminer. It ran through hundreds of re-enumerations until it randomly just started working again. Any idea on what I can give you for diganostics? I've already talked with sidehack about it and know what he needs the next time it happens. "When it drops out, check the voltage across the two pins on the reset header. If it's flatlined at zero volts, that indicates an issue with the temperature sensor. The onboard controller won't enable the mining chips without valid temperature data. If it cycles between zero and around 1.4 volts, there's an issue with the chips and the string isn't turning on right."[2018-03-02 18:41:45.728] Started cgminer 4.10.0
[2018-03-02 18:41:46.048] GSE 0: Terminus BM1384 Bitcoin Miner (10030050)
[2018-03-02 18:41:46.050] GSE 0 TX: 84:00:00:11
[2018-03-02 18:41:46.052] GSE 0 TX: 84:00:00:11
[2018-03-02 18:41:46.457] GSE 0: found 0 chip(s)
[2018-03-02 18:41:46.457] Probing for an alive pool
[2018-03-02 18:41:46.457] Testing pool stratum+tcp://pool.ckpool.org:3333
[2018-03-02 18:41:46.457] GSE 0 failure, disabling!
[2018-03-02 18:41:46.462] GSE 0: setting frequency to 100.00MHz
[2018-03-02 18:41:46.464] GSE 0 TX: 82:07:83:1C
[2018-03-02 18:41:46.465] GSE 0 TX: 84:00:04:00
[2018-03-02 18:41:46.728] Pool 0 difficulty changed to 4000
[2018-03-02 18:41:46.775] Pool 0 message: Authorised, welcome to ckpool.org 1DtRzACnDAr2SPXMyAp3pLMfREPch3PbhA!
[2018-03-02 18:41:46.775] Stratum authorisation success for pool 0
[2018-03-02 18:41:46.775] Pool 0 stratum+tcp://pool.ckpool.org:3333 alive
[2018-03-02 18:41:46.828] Pool 0 difficulty changed to 32
[2018-03-02 18:41:46.828] Network diff set to 3.01T
[2018-03-02 18:41:46.828] New block: 0000000000000000002915f5244780934423a32d8f97d795a1606d964586849a... diff 3.01T
[2018-03-02 18:41:47.458] Testing pool stratum+tcp://pool.ckpool.org:3333
[2018-03-02 18:41:47.458] Work update message received
[2018-03-02 18:41:49.459] (5s):0.000 (1m):0.000 (5m):0.000 (15m):0.000 (avg):0.000h/s
[2018-03-02 18:41:52.458] Testing pool stratum+tcp://pool.ckpool.org:3333
[2018-03-02 18:41:52.768] GSE 1: Terminus BM1384 Bitcoin Miner (10030050)
[2018-03-02 18:41:52.771] GSE 1 TX: 84:00:00:11
[2018-03-02 18:41:52.773] GSE 1 TX: 84:00:00:11
[2018-03-02 18:41:53.176] GSE 1: found 0 chip(s)
...
restart pc
...
change usb ports
...
reset Terminus power
...
restart cgminer
...
[2018-03-02 20:35:33.093] Testing pool stratum+tcp://pool.ckpool.org:3333
[2018-03-02 20:35:37.086] GSE 29: Terminus BM1384 Bitcoin Miner (10030050)
[2018-03-02 20:35:37.088] GSE 29 TX: 84:00:00:11
[2018-03-02 20:35:37.091] GSE 29 TX: 84:00:00:11
[2018-03-02 20:35:37.495] GSE 29: found 0 chip(s)
[2018-03-02 20:35:37.497] Hotplug: GekkoScience added GSE 29
[2018-03-02 20:35:37.499] GSE 29 failure, disabling!
[2018-03-02 20:35:37.500] GSE 29: setting frequency to 100.00MHz
[2018-03-02 20:35:37.504] GSE 29 TX: 82:07:83:1C
[2018-03-02 20:35:37.505] GSE 29 TX: 84:00:04:00
[2018-03-02 20:35:38.094] Testing pool stratum+tcp://pool.ckpool.org:3333
[2018-03-02 20:35:42.867] GSE 30: Terminus BM1384 Bitcoin Miner (10030050)
[2018-03-02 20:35:42.868] GSE 30 TX: 84:00:00:11
[2018-03-02 20:35:42.873] GSE 30 TX: 84:00:00:11
[2018-03-02 20:35:43.081] Hotplug: GekkoScience added GSE 30
[2018-03-02 20:35:43.089] GSE 30 TX: 84:00:00:11
[2018-03-02 20:35:43.094] Testing pool stratum+tcp://pool.ckpool.org:3333
[2018-03-02 20:35:43.094] GSE 30 RX: 13:82:90:FF:0F
[2018-03-02 20:35:43.095] GSE 30 RX: 13:82:90:FF:0F
[2018-03-02 20:35:43.096] GSE 30 RX: 13:82:90:FF:0F
[2018-03-02 20:35:43.097] GSE 30 RX: 13:82:90:FF:0F
[2018-03-02 20:35:43.097] GSE 30 RX: 13:82:90:FF:0F
[2018-03-02 20:35:43.098] GSE 30 RX: 13:82:90:FF:0F
[2018-03-02 20:35:43.099] GSE 30 RX: 13:82:90:FF:0F
[2018-03-02 20:35:43.100] GSE 30 RX: 13:82:90:FF:0F
[2018-03-02 20:35:43.203] GSE 30: found 8 chip(s)
[2018-03-02 20:35:43.311] GSE 30: setting frequency to 81.25MHz
[2018-03-02 20:35:43.312] GSE 30 TX: 82:06:03:18
[2018-03-02 20:35:43.316] GSE 30 TX: 84:00:04:00
[2018-03-02 20:35:43.317] GSE 30: sending chain inactive for 8 chip(s)
[2018-03-02 20:35:43.319] GSE 30 TX: 85:00:00:0F
[2018-03-02 20:35:43.322] GSE 30 TX: 01:00:00:19
[2018-03-02 20:35:43.322] GSE 30 RX: 80:0C:00:03:00
[2018-03-02 20:35:43.323] GSE 30: chip reported frequency of 81.25MHz
[2018-03-02 20:35:43.324] GSE 30 TX: 01:20:00:01
[2018-03-02 20:35:43.325] GSE 30 RX: 80:0C:00:03:00
[2018-03-02 20:35:43.327] GSE 30: chip reported frequency of 81.25MHz
[2018-03-02 20:35:43.327] GSE 30 RX: 80:0C:00:03:00
[2018-03-02 20:35:43.328] GSE 30: chip reported frequency of 81.25MHz
[2018-03-02 20:35:43.329] GSE 30 RX: 80:0C:00:03:00
[2018-03-02 20:35:43.329] GSE 30 TX: 01:40:00:0C
[2018-03-02 20:35:43.330] GSE 30: chip reported frequency of 81.25MHz
[2018-03-02 20:35:43.334] GSE 30 TX: 01:60:00:14
[2018-03-02 20:35:43.334] GSE 30 RX: 80:0C:00:03:00
[2018-03-02 20:35:43.336] GSE 30: chip reported frequency of 81.25MHz
[2018-03-02 20:35:43.337] GSE 30 RX: 80:0C:00:03:00
[2018-03-02 20:35:43.338] GSE 30: chip reported frequency of 81.25MHz
[2018-03-02 20:35:43.338] GSE 30 RX: 80:0C:00:03:00
[2018-03-02 20:35:43.339] GSE 30 TX: 01:80:00:16
[2018-03-02 20:35:43.339] GSE 30: chip reported frequency of 81.25MHz
[2018-03-02 20:35:43.340] GSE 30 RX: 80:0C:00:03:00
[2018-03-02 20:35:43.341] GSE 30: chip reported frequency of 81.25MHz
[2018-03-02 20:35:43.343] GSE 30 TX: 01:A0:00:0E
[2018-03-02 20:35:43.350] GSE 30 TX: 01:C0:00:03
[2018-03-02 20:35:43.352] GSE 30 TX: 01:E0:00:1B
[2018-03-02 20:35:43.354] GSE 30: open cores @ 81.25MHz
[2018-03-02 20:35:45.099] Work update message received
[2018-03-02 20:35:45.643] GSE 30: start work @ 81.25MHz
[2018-03-02 20:35:45.888] GSE 30 RX: C5:38:04:81:84
[2018-03-02 20:35:45.889] GSE 30: Device reported nonce: c5380481 @ 04
its been running strong since (~11 hours now) but I want to make sure you have everything you need for diagnostics. |
|
|
|
Sorry I've been busy and It old but still important Can you tell me why you think this unit is junk? and/or provide a link to a single unit PSU? I actually run my personal rigs on 92% efficient HP1200 w/Gekko break out boards but I need a PSU for single unit sales. |
|
|
|
Hey VH/Sidehack. Super excited for this release. For the barrel jack connector, i saw on the announcement release, it uses about 4.5 amps at 12V. So based on that, a standard LED strip light power pack should work. something like this? http://amzn.to/2FsOMP1100MHz (44GH) 660mV/node 2.64V total; 12V 1.4A for 16.8W/0.38J/GH 125MHz (55GH) 660mV/node 2.64V total; 12V 1.7A for 20.4W/0.37J/GH 150MHz (66GH) 660mV/node 2.64V total; 12V 2.0A for 24.0W/0.36J/GH 175MHz (77GH) 693mV/node 2.77V total; 12V 2.5A for 30.0W/0.39J/GH 200MHz (88GH) 715mV/node 2.86V total; 12V 3.1A for 37.2W/0.42J/GH 225MHz (99GH) 755mV/node 3.02V total; 12V 3.8A for 45.6W/0.46J/GH 250MHz (110GH) 770mV/node 3.08V total; 12V 4.4A for 52.8W/0.48J/GH 275MHz (121GH) 770mV/node 3.08V total; 12V 4.9A for 58.8W/0.49J/GH |
|
|
|
Featuring Fast Same Day U.S. Shipment of Instock Hardware from East Coast for Direct Sales. Accepting Paypal, Bitcoin, most major Credit Cards Same Day shipping of all eBay and Amazon Channel sales. Featuring Instock Assorted USB Stick Miners, Server PSU Adapters & More Products are being Added Daily! Custom built GPU miners, both open-air and Rackmounted. Currently building a public mining facility in Ohio, more rates to come. Registered in the State of Ohio and with the United States SBA https://www.419mining.com/shop/http://stores.ebay.com/419mining/http://amzn.to/2El4ZnArunning a special on instock GekkoScience 2PAC USB Miners - use coupon code 'gekkoship' at checkout for free shipping. Thank You! You can PM me for more info or email me at: nick@419mining.com or on fFacebook: https://www.facebook.com/419mining |
|
|
|
|
Show Posts
