Latest posts of: rageprone

Show Posts
Pages: « 1 [2]

on: December 11, 2017, 03:08:11 AM

Quote from: mkmfins on December 06, 2017, 06:37:41 PM Hello, my miner has been like this and after a few seconds everything goes to "X". Can anyone tell me what to do? https://i.imgur.com/KNPutSz.png See if the information here helps : https://support.bitmain.com/hc/en-us/articles/220872007-Possible-problems-for-Antminer-Troubleshooting-for-S7-S9-L3-

on: December 11, 2017, 01:00:30 AM

I couldn't find a single post dealing with GPU rigs which have both nVidia and AMD cards. I have tried again and again to add a profitability miner but it never detects all the cards. I have2x 1080ti, 2x 1050ti and 1x RX570. I click on new Miner > managed profit miner > select nVidia GPU (for profit switching profile) This shows all the 4 nvidia cards (sometimes). Then I add another managed profit manager and select AMD GPU and it will show the 1x RX570 sometimes or mostly it just shows 'interface offline'. The help document isn't very helpful for a software which cost me $70. Can anyone help me configure my "awesome" miner, please?

on: December 03, 2017, 05:21:47 PM

Quote from: blissz on November 01, 2017, 09:41:56 PM Quote from: shaninium on November 01, 2017, 09:34:31 PM Impressive, well done. Undervolting would void the warranty prob like with oc. Yes I will add this to the topic as this definitely voids the warranty on the mining boards On the other hand, this will improve efficiency and heat problems, so on average this will improve the lifetime of the miner Is it possible to detect modded firmware or clock changes if the device is hard reset?

on: November 19, 2017, 08:43:04 AM

Is there any discord/slack/reddit page for interzone? Need help with setting my second ITZ masternode.

on: November 11, 2017, 06:16:38 AM

How's this coming along? I'm using the same instructions but can't seem to get past the sentinel stage. When I do ./venv/bin/py.test ./test, I get an error saying - No such file or directory: '/root/.monacoCoinCore/monacoCoin.conf' monacoCoinCore must be installed and configured, including JSONRPC access in monacoCoin.conf Quote from: bambambam on October 30, 2017, 10:49:56 AM Noob alert I'm about to set up my first masternode and have a quick question before I start. I'm following this guide: https://cryptomat.com/setup-monaco-masternode-xmcc/ Is there any reason why I shouldn't follow this guide? Also, just want to confirm that can I close my wallet on my laptop after activating masternode and unlocking my wallet? Thanks!

on: November 09, 2017, 04:04:44 AM

Hi all! I'm trying to setup a das masternode. I have the Das Core version v0.12.1.5-g55a53cc (32-bit) running on Windows 10 Pro 64bit It shows: No block source available - 2 days behind for over 20 hours now. Any suggestions to make the wallet sync? Thanks!

on: November 05, 2017, 05:39:19 PM

Hi freetrax, could you please point me towards a good resource which explains how to GPU mine XMCC either solo or in a pool? Thanks in advance! Quote from: freetrax on August 12, 2017, 05:23:45 PM Quote from: lupanar on August 12, 2017, 05:05:54 PM - Max coin available : unllimited A little bit scarry spec, unlim coin can be worth nothing in future. Hi lupanar, thank's four your note Actually block generation rule : 1 MCC per block after 6 years generation after is possible only POS and stop POW.

on: November 05, 2017, 05:01:40 PM

can you please point me to a guide to setup xmcc mining? thanks!! Quote from: nvMiner10 on August 12, 2017, 07:00:14 PM Hi dev, this looks exciting! new to this, so bare with me.... I am setting up my 4x nvidia gpu miner now. Will report with feedback EDIT: I am using sgminer and getting an error Pool 0 slow/down or URL or credentials invalid. I get the correct response when i go to 127.0.0.1:PORT but my miner doesn't want to mine?

Pages: « 1 [2]