Una dudilla jejeje podria pasar la carpeta de bloques de un PC a otro sin copiar los wallet, y asi tendria los clientes sincronizados con diferentes wallet pudiendolos abrir a la vez sin tener problemas verdad??
Saludos
edito:Las direcciones donde he enviado Btcs tambien se guardan en el wallet? porque nunca lo he restaurado.
|
|
|
Pues suerte entonces compañero, espero q vaya bien.
|
|
|
Muy caro, por la mitad me lo quedo
|
|
|
Hola chicos,
me gustaría saber si es posible conectar un equipo de minado bitcoin KNC Jupiter de 550 Kh/s casi anticuado a una pool actual de monedas SHA-256. Supongo que muchos equipos dejarán de ser rentables en poco tiempo y sería una muy buena forma de aprovechar la inversión.
¿Alguíen está en la misma situación?
Saludos y gracias.
por cuanto te lo venden jajaja, con buena refrigeracion llega a 700Gh/s...... Te lo compro jajajajjaja
|
|
|
somebody can explain me how change cgminer for bfgminer?
|
|
|
150€ las 5 placas, envió a cargo del comprador
|
|
|
Hi, I have 2 butterflylabs single sc 60 gh / s, I think this post is aimed for the jalapeno, but it could make the single 60gh Oc / s?
Forgive my English I'm Spanish.
regards
|
|
|
The Bermod 0.4 operates in the firm 1.0? Júpiter october 4vrm
|
|
|
Since the post Hacking The KNC Firmware: Overclocking is very extensive and configurations when comparing a very slow task is done, we can put our configuration each with screenshots, version firmware, etc and the problems we have found when doing so.
So it would be easier for new users inexperienced.
I am Spanish, forgive my English, use google translator :-)
|
|
|
Edit to say, after to put again the firm 0.99.1 tune, i have a little problem with voltages.. it was crazy.. now is working well after reset to factory defaults in advanced but a line 12v of my 1100w PSU now is dead, i got a screenshot, any idea of this? The VRM are designed for 40W, many of us regularly push them to between 50-60W. At 70W per VRM I think you are on your own in new territory! Your screenshot shows 70W per die (per VRM also). 70W x 4 die = 280W per ASIC Add AT LEAST 10% to that because the VRM's use that much before even cooking them by overclocking. OVER 300 Watt per ASIC is what your power supply was asked to do before failure. (you were asking for >1200W from a 1100W supply) I suggest 300W per ASIC is possibly too much. Almost definately too much for a single PCIe 6 pin power connector. You can install another on each module, KnCMiner provided for that on the PCB. YMMV The power supply was broken, leaving to run a 12v rail. Now he's running a cooler master 1300w, and it seems that everything works normally. have if I can get more power, which would secure V for each die since I have high temperatures.
|
|
|
I used the method of flashing 99.2E then back to 99.2, this enables the 8vrm's and then i just proceeded to tune and OC. Been running very stable with low HW and some buzzing noise for about a week.
the volts are pretty even among each pair, nothing additional done, no problems here.
ok, so my jupiter vrm October 4, 8vrms could change, I am not very clear about this.
|
|
|
clock setting 271, been running fr over a week now
As voltage has to die each orient?
|
|
|
780 gh
What is November or October Jupiter?
It is a Octember Unit, or maybe it was a Novober you can put your configuration?
|
|
|
I will start with a warning. It is unknown if this is safe. KnC may have turned off the VRMs due to that there is a problem with the design. You board might burn! On the other hand they ran with all VRMs turned on for a few weeks when they were new without any major issues. I have run a few machines with 8VRMs for almost 2 weeks without problems. Some machines will start buzzing pretty loud, I have no idea why.
bondus thx ! Is the buzzing 1 VRM, ALL VRM's, or just a few? DISCLAIMER: I have Oct 4 VRM hardware. I have extra VRM's(and associated parts) that I thought to install, that is why I have studied it. At this point not cost effective, at over .25 BTC ( >USD$125 ) per ASIC in VRM's alone. I have 'ideas' why 8 VRM's MIGHT misbehave. (notice the lack of absolutes in the above sentence!) ** Massive text with ideas to explain buzzing and safety *** Too bad I do not have access to a proper electronics lab Most of your ideas could be easily tested with a scope and some other basic tools. But I have made some other observations that might be interesting: Iout and Vout from the two VRMs in the pairs are not even. Typical values (as reported by the VRMs): table] VRM Nr | V | A | 0 | 0.8154 | 24.8750 | 1 | 0.7998 | 27.6250 | 2 | 0.8066 | 30.3125 | 3 | 0.8164 | 26.8125 | 4 | 0.8184 | 30.5000 | 5 | 0.8096 | 30.0000 | 6 | 0.8235 | 27.6250 | 7 | 0.8164 | 31.8750 |
0,3 and 6 have slightly higher voltage that the other VRM in each pair. The pair 4,5 is pretty even. Current is a bit higher on the VRMs with lower voltage. It looks the same on many different boards. You would expect voltage and current to be the same on both VRMs in a pair. Odd. The buzzing gets louder the more power you use. You can clearly hear when a block is found I haven't had time yet to open a box and check what VRMs are buzzing. Since you have ordered the parts you must know the value of then RTUNE and RTrim resistors for the VRMs? hmm maybe you should copy my 8vrm board then i have to stick my ear next to it to hear a faint buzzing.... tiozes: ppl been having problems going from 1.0 to 99.1 tune or i think any tune...should go back to 99fw then 99.1 tune yes, with 0.99.1 has returned everything to normal, go fuck have you done for 4Vrms jupiter of October. I was hoping to pass my jupiter 221 as 231 dies. That could put a V max each die? temperatures are at 56 ° C maximum and have sinks in the vrms. 654Gh avg a 221 regards
|
|
|
I copy cgminer.sh run but did not work, but the firm was 0.99.1tune. 0.99 will use the copied file and will update the firm 1.0 how do I put the bfgminer and not cgminer? regards Edit to say, after to put again the firm 0.99.1 tune, i have a little problem with voltages.. it was crazy.. now is working well after reset to factory defaults in advanced but a line 12v of my 1100w PSU now is dead, i got a screenshot, any idea of this?
|
|
|
You think leave it as it is
Hashing at 640 gh Code 211
And firmware 1.00
How did you overclock 1.0? The cgminer.sh file is different. +1 I have a jupiter October 4vrm to 647Gh using 221 firm 0.99.1 tune, I've updated to 1.0 and now firm not give OC, the lines are different from 0.99.1 tune. help please
|
|
|
Con una CPU intel 3930k de 6 cores y 12hilos a 4,5ghz, cuantos€ se podrían sacar aprox al mes?
Porque no se si me compensara...
Saludos
|
|
|
Buenas a todos, con tanta moneda como hay ahora no tengo ni idea de cual podria minar usando solo CPU y que merezca la pena.
A ver si alguien puede contar sus experiencias usando solo CPU.
Saludos
|
|
|
Buenas a todos, hace tiempo que estoy intentado validar mi cuenta y no soy capaz, les he presentado dni, certificado de empadronamiento y recibo de pago del seguro de coche que es lo que tenia a mano y nada, no hay forma, alguien sale alguna alternativa para verificarla?
Porque me pongo en contacto con ellos y no hay manera....
Saludos y perdón por el Offtopic
Lo que quieren es una factura de la luz o del agua, o el gas. Son así... Sobre la gente que estais pensando en meter pasta en Gox, no metáis mas de lo que estéis dispuestos a perder. Es más arriesgado de lo que parece. Pues mal asunto, porque vivo con mis viejos y claro todo va a nombre de ellos, porque el movil lo meto por el negocio de mi padre por lo que ni eso puedo mandarles....
|
|
|
|