I mined on mineshaft 1.0 but when 2.0 launched there have been no pools for decent coins so I was forced to go elsewhere. It would be nice if you had at least Eth, and Zec, I would like to see true stratum pools for Music and UBQ.

Go nitro + or PowerColor I have heard a ton of bad things about the non + cards.

For $1600 I can fully setup 2 4 Card Rigs using 775 Motherboards, Core 2 Duo's, 4GB DDR2, 60GB SSD, 1000W PSU
Which would be making about $600-$700/M right now all Bios Modded Mining ETH pulling from 670W - 780W at the wall per Rig Depending on the Card Quality.

I don't know were you Live but I am in Ohio USA and I run a small Investment Group for Locals. My Groups Terms are as follows.
(**After Power is Deducted**)
10% of Profits are set back for potential Maintenance
15% cut of Profit for 24/7 Rig Monitoring/Troubleshooting
75% Goes to you until 100% ROI
After 100% ROI (Equipment Ownership reverts to the Group)
10% of Profits are set back for potential Maintenance
15% cut of Profit for 24/7 Rig Monitoring/Troubleshooting
8% Goes to the Groups Management
67% Goes to you until the rig is no longer profitable


If Maintenance Has not been used by the time the rig is no longer profitable it will be split 50/50 or can be used 100% to Upgrade the Rig with a renewed investment.

We are responsible for maximizing uptime and * also ensuring that the equipment is the most profitable *
*(Unless you are mining to hold a Coin VS Fiat)*

ROI is calculated at the time of coin payout so if eth is $60 at the time of a 1 ETH payout your ROI amount would be $45 and It is not re-calculated If say the value of eth goes up or down after the time of payout so you could achieve more than 100% ROI by the time we calculate that your full ROI has been returned.

Only 2 Rigs are using 2.9 the others are all still on 2.8.1 so I am guessing there was a issue on the server side were for some reason it had some null values returned from the Database or the json whichever is being used to calculate most profitable coin.

I am using 16.11.5 I have a mixed rig with RX 470's (4GB Cards) and R9 270X (2GB cards) and when setup this way I am still getting 15MH/s out of the 270X's but without 1 470 per 270X the 270X's won't mine. My guess is that the Dag is being shared from the 4GB cards.

I have both Red Devil and Red Dragon's all are 470 4GB cards

From my experience the Red Devil cards do not Undervolt very well and run hotter than the Red Dragon cards.

Example (All Bios Modded Cards):

Red Devil Samsung Memory (4 card Rig)
Core: 1150MHZ
Mem: 2010MHZ
Voltage: 980mv
Temps: 74 °C|69 °C|77 °C|72 °C|
FANS: 97 %|90 %|99 %|100 %|
Rig Speeds (Dual Mining)
Ethereum: 118MH/s
Decred: 2161MH/s
Kill-A-Watt Power Usage: 780W for the Rig

Same Configuration / Setup the same all the way down to the same room / but Red Dragon Samsung Memory cards (4 card Rig)
Core: 1150MHZ
Mem: 2010MHZ
Voltage: 920mv
Temps: 59 °C|62 °C|65 °C|68 °C|
FANS: 78 %|98 %|97 %|100 %|
Rig Speeds (Dual Mining)
Ethereum: 121MH/s
Decred: 2421MH/s
Kill-A-Watt Power Usage: 720W for the Rig

Auto Algo Broken
One rig switched to mining zcl which is disabled, another switched to Pasc which is disabled, a third switched to stating unknown which I'm guessing was zcl based on it running opyiminer again Disabled

http://www.awesomescreenshot.com/image/2446868/bf61c9c642bddaedd3a79e7b5aeb8919

I returned all my XFX RX 470 4GB cards as they were dropping like flies However I have not had a single powercolor card fail.

Request:

You already have a graph for the rig speeds but I would like to have a graph to monitor the temps of the cards in each rig.

Note: Claymore-Eth 9.3 has been released have done testing on a single card and it is more stable so far.

3 options
1. Use DDU to remove drivers and then install 16.11.5
2. If using this driver or a lower revision simply re-install
3. If you want to use newer drivers make sure they are pixelpatched to bypass the driver signature check.

Pair your 2GB cards with 4GB cards in a 1 to 1 fashion and they will then be able to mine the devfee.

I have 5 rigs with 3 2GB 7870XT's paired with 3 4GB 280X cards in each rig and have had no issues.

v9.2 is more stable speeds so far but with a small hash rate reduction however the more stable speeds should out weigh the slower shown performance. Will know in about 24 Hrs.

Do some bench-marking or just use the nicehash miner, the other option is to do some research that will tell you what you need to know.

Estimated Claymore update in a few hours.

Looks like you may have to have another update tonight, DCR changed the headers so at least claymore will have a fix out pretty soon for dual mining.

I am still running my 2GB cards for eth You just have to pair them 1 to 1 with 4gb cards and use claymores miner I'm still getting 15MH/s out of my old 270's

Samsung you use the 1750 Strap and all my samsung 470 4gb cards are doing 29.5 to 32 MH/s

Fantastic.

New Feature request:
Ability to Group Rigs to mine different coins

Example
Rig with 2GB cards can't mine eth or etc but can mine music, ubiq ETC
then
2 Rigs with 4GB cards that can mine everything

Request support for FireIce XMR-Stak-AMD, XMR-Stak-NVIDIA, XMR-Stak-CPU
CPU
https://github.com/fireice-uk/xmr-stak-cpu
AMD
https://github.com/fireice-uk/xmr-stak-amd
NVIDIA
https://github.com/fireice-uk/xmr-stak-nvidia

I am getting better hashrates for XMR using this over all other Cryptonight Miners Getting 750 vs 620 per rx 470 and it uses a web interface for stats.