I am pretty sure the answer is no, but would it be possible to run 1 S1 (possible OC) and 1 BE Cube (on low) with a Corsair Builder 750 PSU?
What is the wattage requirements for the BE Cube? |
|
|
|
So you want to buy coins through Paypal?
How many?
You do realize you have to pay first and sent the payment as "to a friend" right?
I cannot send "to a friend" from the country that I'm currently in but I can pay the additional fees. I need 0.12BTC Good luck. Nobody will accept to sent you BTC with the fear of a chargeback. Pointless post is pointless Well said. So why did you post in the first place? |
|
|
|
So you want to buy coins through Paypal?
How many?
You do realize you have to pay first and sent the payment as "to a friend" right?
I cannot send "to a friend" from the country that I'm currently in but I can pay the additional fees. I need 0.12BTC Good luck. Nobody will accept to sent you BTC with the fear of a chargeback. |
|
|
|
12.7 btc is ~$7k
Most people doublecheck(the last 3 numbers/letters or whatever) when they send a $7k transfer
Why didn't u doublecheck?
^^^ True. I check first five and last five to make sure. |
|
|
|
|
So you want to buy coins through Paypal?
How many?
You do realize you have to pay first and sent the payment as "to a friend" right?
|
|
|
|
can anyone explain to me what is going on this unit has only been running for like a 4 days at stock settings
AntMiner
Chain# ASIC# Frequency Fan Temp ASIC status
1 2 350 1200 41 xxxxxxxx xxxxxxxx xxxxxxxx xxxxxooo
2 32 350 0 42 oooooooo oooooooo oooooooo oooooooo
Have you tried powering down? Mine did that a couple of days ago. I lost 16 of them. I just powered down the psu and waited for a couple of minutes, and powered it back up. Everything was fine. ^^^ What he said. Try it. Also if you get xxxxx yet your hashing speeds are normal then you are fine. |
|
|
|
Is this the value that I have to look "Average generation time for a block (solo)" to know how time I need to close a block? or what? Yeap |
|
|
|
Trying to troubleshoot an issue I've been having with mine. Once every few hours, my S1 will start a fairly quiet beeping session that lasts for 30-60 seconds. Hashing speed is degraded at this time. There is sometimes a louder beep announcing the end of the cycle.
It does not appear to be related to internet connectivity, as I monitor my pings fairly closely, and it seems stable during these outages. The miner is overclocked, but the issue happens even at stock speeds. The temps on the board seem fairly stable at around 45-46, though it drops into the 30s during these cycles. Overall HW errors fluctuate from .5-1%. Any ideas of what could be going on?
I used to have this same issue. Happened to all my Ants and no, it was not a problem in my network. Got it fixed with a firmware update, you should give it a try. It's been in my possession about two weeks, and I updated the firmware first-thing from here. I'll update again - just to be sure. It's not a firmware problem. What version have you got? v1.4 or v1.5? can you ping properly? Do you get ntp errors in your system log? How can I determine what version I have? Pings work fine currently (currently not beeping). No NTP errors in the log. OK, go to your wan settings through - Network - Interfaces. Then EDIT wan connection. Change DNS to: 8.8.8.8 and add another one as: 8.8.4.4 I think you should be set  EDIT: The version is shown on your Ants Boards. Pool settings are correct. It's been hashing to them fine - except once an hour or so. I applied the fix remotely. I'll let you know if it worked. What PSU are you using? I'm using the EVGA 1000w P2. Currently only powering one, will eventually be powering two. Still happening. Ping stats from the computer on the same switch show no network outage. Try using the WiFi connection. |
|
|
|
I sent support a message mid hack as the failed attempts were coming in. best they said to do was change my email and password. all attempts were different ip address so the probably had control of a botnet. That kind of makes sense but my password held up so maybe i shouldn't change it.
anyway there is no way to change my username, thats part one of what they need to hack in.
cex should be using a unique id instead of user names in their referral links imo.
They were using Tor |
|
|
|
|
Yeah and the coins were mixed yesterday. GONE.
I hope it wasn't BTC from forum members.
I warned everyone from the start.
|
|
|
|
and how would they get your usernames to even try it...
think long and hard about the possibiities
It's in his sig  |
|
|
|
Trying to troubleshoot an issue I've been having with mine. Once every few hours, my S1 will start a fairly quiet beeping session that lasts for 30-60 seconds. Hashing speed is degraded at this time. There is sometimes a louder beep announcing the end of the cycle.
It does not appear to be related to internet connectivity, as I monitor my pings fairly closely, and it seems stable during these outages. The miner is overclocked, but the issue happens even at stock speeds. The temps on the board seem fairly stable at around 45-46, though it drops into the 30s during these cycles. Overall HW errors fluctuate from .5-1%. Any ideas of what could be going on?
I used to have this same issue. Happened to all my Ants and no, it was not a problem in my network. Got it fixed with a firmware update, you should give it a try. It's been in my possession about two weeks, and I updated the firmware first-thing from here. I'll update again - just to be sure. It's not a firmware problem. What version have you got? v1.4 or v1.5? can you ping properly? Do you get ntp errors in your system log? How can I determine what version I have? Pings work fine currently (currently not beeping). No NTP errors in the log. OK, go to your wan settings through - Network - Interfaces. Then EDIT wan connection. Change DNS to: 8.8.8.8 and add another one as: 8.8.4.4 I think you should be set EDIT: The version is shown on your Ants Boards. Pool settings are correct. It's been hashing to them fine - except once an hour or so. I applied the fix remotely. I'll let you know if it worked. What PSU are you using? |
|
|
|
Trying to troubleshoot an issue I've been having with mine. Once every few hours, my S1 will start a fairly quiet beeping session that lasts for 30-60 seconds. Hashing speed is degraded at this time. There is sometimes a louder beep announcing the end of the cycle.
It does not appear to be related to internet connectivity, as I monitor my pings fairly closely, and it seems stable during these outages. The miner is overclocked, but the issue happens even at stock speeds. The temps on the board seem fairly stable at around 45-46, though it drops into the 30s during these cycles. Overall HW errors fluctuate from .5-1%. Any ideas of what could be going on?
I used to have this same issue. Happened to all my Ants and no, it was not a problem in my network. Got it fixed with a firmware update, you should give it a try. It's been in my possession about two weeks, and I updated the firmware first-thing from here. I'll update again - just to be sure. It's not a firmware problem. What version have you got? v1.4 or v1.5? can you ping properly? Do you get ntp errors in your system log? How can I determine what version I have? Pings work fine currently (currently not beeping). No NTP errors in the log. OK, go to your wan settings through - Network - Interfaces. Then EDIT wan connection. Change DNS to: 8.8.8.8 and add another one as: 8.8.4.4 I think you should be set EDIT: The version is shown on your Ants Boards. EDIT 2: Are your pool setting correct? |
|
|
|
OK, all my Ants had NTP errors. After disabling them, both from interface and SSH and after giving the right details in connection interface they all worked like a charm Also, disabling NTP through SSH for v1.4 to v1.5 is different. That's why I was asking. |
|
|
|
Trying to troubleshoot an issue I've been having with mine. Once every few hours, my S1 will start a fairly quiet beeping session that lasts for 30-60 seconds. Hashing speed is degraded at this time. There is sometimes a louder beep announcing the end of the cycle.
It does not appear to be related to internet connectivity, as I monitor my pings fairly closely, and it seems stable during these outages. The miner is overclocked, but the issue happens even at stock speeds. The temps on the board seem fairly stable at around 45-46, though it drops into the 30s during these cycles. Overall HW errors fluctuate from .5-1%. Any ideas of what could be going on?
I used to have this same issue. Happened to all my Ants and no, it was not a problem in my network. Got it fixed with a firmware update, you should give it a try. It's been in my possession about two weeks, and I updated the firmware first-thing from here. I'll update again - just to be sure. It's not a firmware problem. What version have you got? v1.4 or v1.5? can you ping properly? Do you get ntp errors in your system log? |
|
|
|
Trying to troubleshoot an issue I've been having with mine. Once every few hours, my S1 will start a fairly quiet beeping session that lasts for 30-60 seconds. Hashing speed is degraded at this time. There is sometimes a louder beep announcing the end of the cycle.
It does not appear to be related to internet connectivity, as I monitor my pings fairly closely, and it seems stable during these outages. The miner is overclocked, but the issue happens even at stock speeds. The temps on the board seem fairly stable at around 45-46, though it drops into the 30s during these cycles. Overall HW errors fluctuate from .5-1%. Any ideas of what could be going on?
If you have beeping that means you have connection problems. Check that your connection is stable. EDIT: Lan or WiFi? |
|
|
|
|
Show Posts
