I believe it's the same story as for 5XXXs, you must be using Catalyst 12.8 drivers.

expiry only works in junction with submit-no-stales. As I understand it if you've had the data longer than expiry then your cgminer considers it stale, even though it might not really be stale. I deleted --expiry and --submit-no-stales from my config file.

I've tried queue from 0 to 10 and see no effect. I've tried scan-time from 5 to 120 and see no effect. I think kslavik is right that they do not work for stratum servers. I'm going to delete them and see.

I tried switching pools from cgminer by selecting "P" then "S" then the pool number from the list. However, when I check MP the miner is still mining the same pool as the first pool listed in my configuration URL list. Anyone noticed that 

I bought a new fan for $14 on ebay and fixed my 5970 with just a screwdriver.

I love you man!!! 

BTW, I can't open the webpage today. Behind in my reading too.

CosmosCoin (CMC) gets my vote 

I want to solo mine with 10 miners on a home network. Do I need to leach a longpoll from someone's pool on each miner, or just the miner hosting my coin wallet 
TIA

C4meyHgbDT5sKWKyMCpVXgWvA7TL3PrtWR

Thanks 

Maybe it should be named BottledCrap (CRP)  

He's blind drunk 
I think he meant "seem" and not "see."

Thanks for the tip. I'm going to get CGWatcher.

I'm still plagued by unrecoverable stratum disconnects when I try to mine one of the embryonic coins. I just can't afford to use MP until a new release of cgminer fixes this bug. It never happens on LTC or NVC and I think FTC. I sure wish there was a MultiPort just for LTC, NVC and FTC.

I see folks are mining CAPS again, are they going to get to keep their earnings or are they just spinning their wheels mining orphans?

I cannot connect to either TRC server.

You'd think you'd be grateful that your NanoCoin got the endorsement of MultiPool. Too bad Big Vern doesn't have the quality control we do and should be orphaned for causing the fork.

If Cryptsy and Big Vern caused the fork then their chain should be orphaned.

How can you tell where to set queue, expiry and scantime. I've tried all kinds of values, except the very low ones you use, and do not see any change. Do these parameters actually do anything? I asked in the cgminer forum and never got an answer.

I suspect there's a bug in the Profit Snapshot. I used Burnside's LTC Profitability Calculator and enter my donation as the fee and zero for electricity and my average scrypt hashrate to get a daily value and converted to BTC. The Profit Snapshot is 2.5x higher.

A few days ago it was pretty reasonable so I think the bug is recent.

Has anybody lost coin depositing it to CampBX? I just discovered they dispose of their deposit addresses within a week. My last BTC deposit vaporized.

I'm going to deposit all BTC to my own wallet so I'll have an audit trail. It surprised me that there's no record at Cryptsy or BTC-e of my BTC withdrawals.

Caveat emptor 

Love the new Account page. In an instant I discovered one of my miners asleep on the job 

How do I pick the difficulty that will make the most money for me? By maximizing U

"Without setting ANY parameter..." So you don't any *.conf in your cgminer folder?
"All 3 GPUs are set to OFF..." How did you set the GPUs to off if you didn't set any parameters?

As for memory, I keep hearing how scrypt mining is very RAM intensive. I've heard you need more RAM than you have video memory. I don't see that with my miners, e.g.:
Dedicated 4x7970 miner has 12 GB GDDR5 plus 10 GB DDR3 and I still have 8.69 GB available.
Dedicated 3x7970 miner has 9 GB GDDR5 plus 4 GB DDR3 and I still have 3.02 GB available.
2x7970 on my workstation, several other programs running, has 9 GB GDDR5 plus 8 GB DDR3 and I still have 5.36 GB available.
You might want to go to 4 GB but I suspect your problem is elsewhere.

What TC, I, temp-target and are you changing GPU Vddc
1050/1500 won't even run on my 7970s.